Wayne-Dalton WDTC-20 Advanced Installation Information, Celsius/Fahrenheit Readout, JP1

Page 20

Advanced Installation Information

Celsius/Fahrenheit Readout

Modify your display to read degrees C or degrees F:

To display degrees Celsius:

1.Install jumper on jumper JP1 position A shown in diagram to the right.

2.Press and release the RESET button (using a paper clip or pencil point) on the front of the control unit to activate your setting.

To display degrees Fahrenheit:

1.Do not install jumper or remove jumper on jumper JP1 as shown on position B in the diagram to the right.

2.Press and release the RESET button on the front of the control unit to activate your setting.

JP1

A

OR

B

2

 

JP1

RESET

NORMAL

SAVE

 

ENERGY

20

Temperature Offset

Your Wayne-Dalton Z-Wave®enabled Thermostat is very accurate and comes from the factory calibrated to +/- 1º of actual temperature. Temperature Offset can be used

to force the thermostat to match another thermometer in your home to a maximum of +/- 6º.

1.Remove Thermostat Control Unit from the thermostat base.

2.Slide the calibration switch to the ON position.

3.Press either the + or - button on the front of the Control Unit until the desired temperature offset factor is reached.

4.Slide the Calibration switch to the OFF position.

NOTE: If using this feature, Temperature Offset must be adjusted each time the thermostat is RESET or batteries are removed.

OFF

ON

2

ON

 

Calibrate

 

 

4

 

OFF switch

CALIB

 

3

Example: Display shows +2 degree Offset factor

Page 19 Page 21
Image 20
Page 19 Page 21
Contents This manual should be retained for future reference For Model WDTC-20Important Notice Table of Contents Table of ContentsManual Operation Programming Target Temperatures 23-25 WaveProgrammingBasics GlossaryWaveEnabled Thermostat Basics Tools required Package ContentsGeneral Information Installation NextPencil to prevent Wires from falling Removing Existing ThermostatWall Into wall openingMounting Base Screws Pull the wires through the wire hole in the baseThermostat Control Unit Mounting Base Opening. Do not allow wiring between Connect labeled wires only to a terminalMatches your wiring needs. a needle-nose Thermostat mounting base and wallOW2 W Y RH RC G a Wiring InformationHeat Pump Systems Reset IMPORTANT! Additional Wiring NotesJumper Reference Guide JP5 JP3 JP4 JP1 JP2Wire Heat/Cool + C Wire RH YWire W2 W RH Y WireCross Reference Chart Modify Label SchemeCommon Designations for Zoned Hot Water Systems Common Designations for Lennox Heat Pump SystemsWire Heat + C Wiring and Jumper Configuration JP5RH RC G a RH GWire Heat/Cool + C Wiring and Jumper Configuration Step B Connect your wires to the correspondingTerminals on the thermostat base. Wrap wire around JP5 JP3 JP4 JP1Or O Y RH G O W2 W Y RH RC G aJP5 JP3 JP4 JP1 JP2 JP2Your Labeled Wires Box to the left Securely using a Phillips or slotted screwdriverW2 W Y W2 W Slotted screwdriverLow Battery Icon Located on Thermostat LCD Display + AACheck Heat Return to Auto position for Normal operationAdvanced Installation Information Temperature OffsetCelsius/Fahrenheit Readout JP1General Operation Reference Guide OperationGeneral Operation Basics   Programming Target temperatures ProgrammingProgramming Save Heat target temperature Programming Normal Cool target temperatureButton. Target Temp will appear in the display ProgrammingHeat mode, if the temperature falls more than Programming Cool Save target temperatureWaveProgramming WaveProgramming OperationPress and Release Bind button Full Z-WavelogoAlternate Programming Directions Press the ADD Device button in the ThinkEssentials window Programming ExamplesWaveProgramming ThinkEssentials Example Operating Thermostat Normal to Save EnergyDesign TAB Programming ExamplesOn the Wireless Gateway, press WaveProgramming Example with WDHA-12RRemoving Thermostat from Wireless Gateway primary controller WaveAlternate Programming Example with HA-09WD Press and release the Bind button onWaveAlternate Programming ControllerCustomer Support

WDTC-20 specifications

The Wayne-Dalton WDTC-20 is an innovative and versatile garage door opener that stands out in terms of performance, security, and user-friendliness. Designed by Wayne-Dalton, a leader in the garage door industry, the WDTC-20 incorporates modern technologies to provide homeowners with a complete solution for their garage access needs.

One of the main features of the WDTC-20 is its powerful motor which delivers reliable lifting force suitable for standard and heavier doors. The unit is engineered to ensure smooth and quiet operation, making it ideal for residential use where noise reduction is a priority. The opener is compatible with various door types, allowing for easy integration with sectional or one-piece garage doors.

The WDTC-20 incorporates advanced security technology with its rolling code feature. This system generates a new code every time the remote is used, significantly reducing the risk of unauthorized access. Additionally, the opener includes a secure manual release system, providing peace of mind in case of power outages.

A hallmark of the WDTC-20 is its user-friendly interface. The opener features a bright LED lighting system that illuminates the garage space, enhancing visibility during entry and exit. The unit also boasts a wireless keypad option that allows users to open the garage door without needing to carry a remote. This is particularly convenient for households with multiple users.

For tech-savvy homeowners, the WDTC-20 offers smartphone compatibility through its smart hub. By connecting to a home Wi-Fi network, users can control and monitor the garage door remotely via a mobile app. This feature allows notifications for door status, facilitating enhanced security and operability.

In terms of installation, the WDTC-20 is designed for easy and straightforward setup, enabling users to quickly benefit from its extensive features. Additionally, Wayne-Dalton offers robust customer support and a warranty program for peace of mind.

Overall, the Wayne-Dalton WDTC-20 combines strength, security, and technological innovation, making it a compelling choice for anyone in need of a modern garage door opener. Its blend of convenience and safety features ensures that it caters well to the dynamic needs of contemporary living.
Top Page Image Contents