Wayne-Dalton WDTC-20 Pull the wires through the wire hole in the base, Mounting Base Screws

Page 8

Installation

8

Step 3: Mounting Thermostat

Tools required:

Phillips or Slotted Screwdriver Drill

3/16 inch drill bit Hammer Pencil

1.Separate the control unit (front) of the thermostat from the mounting base (back.) Grasp the thermostat and pry the control unit away from the base, lift up to remove the control unit from the base as shown. Set aside the control unit.

2.Pull the wires through the wire hole in the base.

Note: Be careful, do not allow bare wires to touch, or short, each other.

3.Hold the base against the wall with the wires coming through the opening below the terminal block, and position the base for best appearance. Mark the hole positions with a pencil or mount directly to the wall with the two screws provided.

If mounting the base to sheetrock or if using the existing mounting holes, use the plastic anchors provided. Drill a 3/16 in (4.8 mm) hole for the anchors at each screw location. Use a hammer to tap the screw anchors into the hole. Mount the base with the two screws provided.

Note: This thermostat does not require leveling for proper operation.

4.Be certain all wires are threaded through the hole in the thermostat base. Leave wires loose in the opening.

Note: Be careful, do not allow bare wires to touch, or short, each other.

Thermostat

Control Unit

Thermostat

 

Mounting

Base

 

 

Lift up Control

 

unit from Base

Thermostat

 

Wall Opening

Mounting

 

 

 

 

Base

 

 

G

w

 

B

 

Screws

Continued Next Page

Page 7 Page 9
Image 8
Page 7 Page 9
Contents This manual should be retained for future reference For Model WDTC-20Important Notice Table of Contents Table of ContentsManual Operation Programming Target Temperatures 23-25 WaveProgrammingBasics GlossaryWaveEnabled Thermostat Basics Tools required Package ContentsGeneral Information Installation NextPencil to prevent Wires from falling Removing Existing ThermostatWall Into wall openingMounting Base Screws Pull the wires through the wire hole in the baseThermostat Control Unit Mounting Base Opening. Do not allow wiring between Connect labeled wires only to a terminalMatches your wiring needs. a needle-nose Thermostat mounting base and wallOW2 W Y RH RC G a Wiring InformationHeat Pump Systems Reset IMPORTANT! Additional Wiring NotesJumper Reference Guide JP5 JP3 JP4 JP1 JP2Wire Heat/Cool + C Wire RH YWire W2 W RH Y WireCross Reference Chart Modify Label SchemeCommon Designations for Zoned Hot Water Systems Common Designations for Lennox Heat Pump SystemsWire Heat + C Wiring and Jumper Configuration JP5RH RC G a RH GWire Heat/Cool + C Wiring and Jumper Configuration Step B Connect your wires to the correspondingTerminals on the thermostat base. Wrap wire around JP5 JP3 JP4 JP1Or O Y RH G O W2 W Y RH RC G aJP5 JP3 JP4 JP1 JP2 JP2Your Labeled Wires Box to the left Securely using a Phillips or slotted screwdriverW2 W Y W2 W Slotted screwdriverLow Battery Icon Located on Thermostat LCD Display + AACheck Heat Return to Auto position for Normal operationAdvanced Installation Information Temperature OffsetCelsius/Fahrenheit Readout JP1General Operation Reference Guide OperationGeneral Operation Basics   Programming Target temperatures ProgrammingProgramming Save Heat target temperature Programming Normal Cool target temperatureButton. Target Temp will appear in the display ProgrammingHeat mode, if the temperature falls more than Programming Cool Save target temperatureWaveProgramming WaveProgramming OperationPress and Release Bind button Full Z-WavelogoAlternate Programming Directions Press the ADD Device button in the ThinkEssentials window Programming ExamplesWaveProgramming ThinkEssentials Example Operating Thermostat Normal to Save EnergyDesign TAB Programming ExamplesOn the Wireless Gateway, press WaveProgramming Example with WDHA-12RRemoving Thermostat from Wireless Gateway primary controller WaveAlternate Programming Example with HA-09WD Press and release the Bind button onWaveAlternate Programming ControllerCustomer Support

WDTC-20 specifications

The Wayne-Dalton WDTC-20 is an innovative and versatile garage door opener that stands out in terms of performance, security, and user-friendliness. Designed by Wayne-Dalton, a leader in the garage door industry, the WDTC-20 incorporates modern technologies to provide homeowners with a complete solution for their garage access needs.

One of the main features of the WDTC-20 is its powerful motor which delivers reliable lifting force suitable for standard and heavier doors. The unit is engineered to ensure smooth and quiet operation, making it ideal for residential use where noise reduction is a priority. The opener is compatible with various door types, allowing for easy integration with sectional or one-piece garage doors.

The WDTC-20 incorporates advanced security technology with its rolling code feature. This system generates a new code every time the remote is used, significantly reducing the risk of unauthorized access. Additionally, the opener includes a secure manual release system, providing peace of mind in case of power outages.

A hallmark of the WDTC-20 is its user-friendly interface. The opener features a bright LED lighting system that illuminates the garage space, enhancing visibility during entry and exit. The unit also boasts a wireless keypad option that allows users to open the garage door without needing to carry a remote. This is particularly convenient for households with multiple users.

For tech-savvy homeowners, the WDTC-20 offers smartphone compatibility through its smart hub. By connecting to a home Wi-Fi network, users can control and monitor the garage door remotely via a mobile app. This feature allows notifications for door status, facilitating enhanced security and operability.

In terms of installation, the WDTC-20 is designed for easy and straightforward setup, enabling users to quickly benefit from its extensive features. Additionally, Wayne-Dalton offers robust customer support and a warranty program for peace of mind.

Overall, the Wayne-Dalton WDTC-20 combines strength, security, and technological innovation, making it a compelling choice for anyone in need of a modern garage door opener. Its blend of convenience and safety features ensures that it caters well to the dynamic needs of contemporary living.
Top Page Image Contents