Wayne-Dalton 451, 452 Bottom SECTION/ Vertical Track, FIG H Stacking Sections

Page 6

BOTTOM SECTION/ VERTICAL TRACK

Center and level (or support to a known grade level) the bottom section in the opening, using shims if necessary, as seen in FIG H. Temporarily attach the wall angles to the jambs with the appropriate lag screws, as shown in FIG H-1, FIG H-2 and FIG H-3. Allow 1/2” clearance between the section and the vertical tracks as illustrated in the sidereoom requirements illustrations on page 3. It is important that the top of each track is on the same plane.

NOTE: Products being installed to precast or block must use a 3/8” x 3” sleeve anchor to attach the wall angle to the building, as shown in FIG H-3. Use the slots in the wall angle as a drill template and drill a 3/8” hole (3-1/2” deep) and secure to anchor.

Stack the bottom section into position by hooking the left hand roller into the left hand vertical track, as shown in FIG H-4. Insert a roller into the proper, uninstalled right hand end hinge, and place the roller into the right hand vertical track. Lower the roller and hinge into the proper position over the section, and attach to the section in the same manner the left hand end hinge was attached, as described on page 5.

 

 

WALL ANGLE

 

 

5/16” X 1 5/8” LAG

 

FIG H-2

SCREW FOR USE ON

 

 

WOOD JAMBS.

 

 

FIG H-1

 

FIG H-3

 

 

 

5/16” X 1” SELF

 

WALL ANGLE

DRILLING &

13”

 

TAPPING SCREW

 

FOR USE ON STEEL

 

 

 

 

JAMBS.

 

FIG H-1

 

30” OR

 

18”

 

FIG H-2

 

 

 

 

3/8” X 3” SLEEVE

 

VERTICAL TRACK

ANCHOR (BY

 

OTHERS) FOR USE

24”

 

 

ON PRE-CAST

O.C.

 

 

CONCRETE.

MAX

 

 

( DRILL A

 

 

 

 

3/8” X 3-1/2” DEEP

 

 

HOLE)

24”

 

FIG H-3

O.C.

 

MAX

 

 

 

 

STACK THE SECTION

 

 

INTO POSITION, BY

 

 

HOOKING THE LEFT

24”

 

HAND ROLLER INTO

 

THE VERTICAL TRACK

 

 

 

 

AND REPEATING FOR

 

FIG H-4

THE RIGHT HAND SIDE.

 

 

10”

NOTE: TYPICAL FASTENER SPACING.

FIG H-4

 

FIG H

STACKING SECTIONS

Locate the Lock Section (the second section) and insert a roller into the left end hinge. Stack this section into the opening by hooking the roller into the left hand vertical track and lowering the section onto the bottom section, as shown in FIG I. Insert a roller into the proper, uninstalled right hand end hinge, and place the roller into the right hand vertical track. Lower the roller and hinge into the proper position over the section, and attach to the section in the same manner the left hand end hinge was attached, as described on page 5. Verify section alignment, and flip up the upper hinge leaf(s) from the bottom section and secure to the lock section using 1/4”-20 x 7/8” self-drilling screws. Continue to stack the remaining sections in the proper sequence, except for the top section.

6

Image 6
Contents Model 451/452 Aluminum FullView Operating Zone BackroomSideroom Requirements Counterbalance CABLES/ Bottom Brackets FIG C FIG BFIG D FIG F HingesFIG E FIG GBottom SECTION/ Vertical Track FIG H Stacking SectionsTOP BRACKETS/ TOP Section FIG JFIG K Vertical Track Adjustment Horizontal TRACKS/ Adjusting TOP BracketCounterbalance FIG L FIG M-1 FIG M-2FIG N SteelFIG O TWO or More Springs 6 Split Solid Shaft FIG PSpring Turn Chart Winding SpringsFIG Q Rear Supports FIG RBack Hangers Alternate Steel Spring PAD Applications Spring AdjustmentsFinal Adjustments FIG SFIG T FIG U Inside Side Lock Installation Vertical Track Align with Slot in TrackSelf Drilling Screws Lock Section Bottom Section Step Plate InstallationFIG W Exhaust Port Installation Outside Trim RingCable Keeper Installation FIG Y Chain Hoist Installation Standard Lift ApplicationsCable Keeper Roller Holes Pusher Spring FIG ZTOP Section HEX Head Bolts NutsMaintenance and Finishing Instructions Cable ARMCAM ARM Limited Warranty Model 451, 452 & K-AL
Related manuals
Manual 4 pages 39.66 Kb

451, 452 specifications

Wayne-Dalton 451 and 452 are renowned models that stand out in the realm of residential and commercial garage doors, offering a perfect blend of functionality, durability, and aesthetic appeal. Designed to meet the diverse needs of homeowners and businesses, these models incorporate advanced technologies and features that ensure security and ease of use.

The Wayne-Dalton 451 model is particularly distinguished for its exceptional insulation properties. It boasts a 1.5-inch thick door construction, utilizing a polystyrene core that provides superior thermal efficiency. This insulation not only helps in maintaining a stable internal temperature but also enhances energy savings, making it a sought-after choice for regions with extreme weather conditions. The exterior of the door is crafted from high-quality steel that is both rust-resistant and durable, ensuring that it withstands the test of time.

Aesthetically, the 451 model offers a variety of design options, with numerous colors and finishes available. Homeowners can choose between different panel styles and decorative windows, allowing for a high degree of customization to fit any architectural look.

On the other hand, the Wayne-Dalton 452 model elevates the standards further with its unique construction features, providing sound insulation and enhanced durability. The 452 model utilizes a polyurethane core, which not only offers superior insulation but also provides a lightweight design that makes it easy to operate. This model is particularly beneficial for areas that require quieter garage doors, ensuring that daily operations are smooth and unobtrusive.

Both models come equipped with Wayne-Dalton’s signature TorqueMaster® system, which utilizes a unique spring design that is fully enclosed within the door. This innovative feature minimizes the risk of injury from exposed springs and enhances the overall safety of the doors. Additionally, the doors can be paired with various opening systems, including automatic openers, ensuring convenience for users.

In summary, Wayne-Dalton 451 and 452 models are exceptional choices in the garage door market, combining insulation efficiency, safety, and aesthetic flexibility. With advanced technologies and customizable options, these doors are designed to cater to the demanding needs of both residential and commercial environments, making them a reliable investment for years to come.