Wayne-Dalton 2415, 2411 warranty Do not Grease the Inside of the Track

Page 13

Doors 16’ to 18’ use 2 intermediate hangers. Over 18’ use hangers at 6’ max. centers

Intermediate hangers for all doors over 11’ high and over 14’ wide. Positioned half way between jamb and rear hanger.

Use a 3/8” X 3/4” truss bolt for roller clearance.

Lateral brace all hanger angles.

3/8” dia. Bolt should protrude into track to serve as a roller stop.

Use 12 GA. Minimum Apply locking pliers to angle (1-5/8” X 2-3/8”)secure while attaching

hangers.

STEP 10: Attaching the Back Hanger Angles: Apply another locking pliers above the No. 2 or No. 3 roller and then remove the locking pliers from the top roller. With assistance push downward on the door and remove all locking pliers. Carefully raise door until one and a half panels are in the horizontal track, lock door into position using locking pliers.

Space the horizontal tracks 3/4” from section edge and level (or running upward). Using 1-5/8” x 2-3/8” x 12 GA. Min. Angle, secure each horizontal track to the building as shown in Fig. Using 3/8” bolts and nuts . Lateral brace all drop angles once proper spacing is determined.

Doors over 11 ft. high and over 14 ft. wide must have (1) intermediate drop hanger as shown above right side.

Doors between 16’ and 18’ high must have (2) center hanger assemblies as shown above left side. Doors over 18’ high must have center hangers placed at 6’ center max.

STEP 11: Checking the Counterbalance: Release the locking pliers from vertical track and check the door’s counterbalance. Adjust springs if necessary.

STEP 12: Vertical Track and Top Bracket Adjustments: Vertical tracks can now receive final adjustments. Open and close the door a few times, checking and adjusting side clearance (if necessary). Tighten jamb fasteners (lags, teks, and anchors) to permanently secure verticals. Adjust door in or out from jamb by loosening the track to obtain proper seal. Permanently tighten all track bolts. Adjust top bracket roller carrier so that the top section is sealed against header.

STEP 13: Lubrication: Lubricate springs, rollers, and bearings with oil.

DO NOT GREASE THE INSIDE OF THE TRACK.

PG. 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Model 2411 Operating Zone Sideroom Requirements Track 1/4 Graduation 8 Sections High or Less Track 1/4 Graduation 9 Sections High or Less Refer To Strutting Schedule Insert Standard Strutting Schedule 15.2 PSF Black RED Left Side Illus Trates Single Endcaps Hardware TWO Springs TWO Springs Split Shaft Page Spring Turn Chart Do not Grease the Inside of the Track Steel Spring Pad Applications FIG. O Model 2411

2411, 2415 specifications

Wayne-Dalton has long been recognized as a leading manufacturer of high-quality garage doors, and among their popular models are the Wayne-Dalton 2415 and 2411. These models are designed to combine durability, aesthetic appeal, and innovative technology, making them suitable for both residential and commercial applications.

The Wayne-Dalton 2415 is known for its robust construction and versatility. Constructed with superior insulation properties, this model features a three-layer construction that includes an outer steel layer, an insulation core, and an inner steel layer. This design not only enhances thermal performance, helping to maintain a consistent indoor temperature and energy efficiency, but also provides excellent soundproofing qualities. The 2415 is available in various styles and colors, allowing homeowners to customize their garage doors to fit their architectural needs.

In contrast, the Wayne-Dalton 2411 offers a more economical solution without compromising on quality. This model features a two-layer construction that still provides adequate insulation and strength, making it ideal for moderate climates. The 2411 is particularly appealing for homeowners looking for a budget-friendly option that doesn’t skimp on style. It comes with a range of finishes and decorative hardware, ensuring that it can enhance the curb appeal of any home.

Both models are equipped with Wayne-Dalton's patented TorqueMaster® system, which features an end-mounted spring design that is enclosed in a solid steel tube. This system offers enhanced safety by eliminating exposed springs, reducing the risk of injury during operation. Additionally, both the 2415 and 2411 are compatible with Wayne-Dalton’s easy-lift panel design, making them easy to operate manually or with an automatic opener.

Safety features are also a priority in these models. They come with pinch-resistant design that minimizes the risk of injury to fingers when the door is in operation. The doors are tested for durability and wear, ensuring that they can withstand the test of time and continue to function without frequent maintenance.

In summary, the Wayne-Dalton 2415 and 2411 garage doors present homeowners with excellent options tailored to varying needs, whether it is maximum insulation, cost-effective solutions, or advanced safety features. Their combination of durability, aesthetic appeal, and cutting-edge technology makes them a standout choice in today's market.
Top Page Image Contents