ALUMINUM FULL-VIEW 451 & 452 |
Note to specifiers: Words in parentheses indicate frequently specified and highly recommended options. |
PART I – GENERAL | | PART I I – PRODUCTS | 2.05 | Weatherstripping |
1.01 | Section Includes | 2.01 | Manufacturer | A. | Doors shall be equipped with vinyl joint seals between |
A. | Sectional overhead doors [manually] [motor] operated | A. | Wayne-Dalton or approved equal AFV 451/452 | | sections and vinyl“bulb” shaped astragal provided on |
| with accessories and components. | | overhead doors of aluminum alloy 6063-T6 | | the bottom section.Optional top seal and jamb |
1.02 | Related Work | | construction complete as specified in this section and | | seal are available. |
| as manufactured by Wayne-Dalton Corp. | 2.06 | Glazing |
A. | Opening preparation, miscellaneous or structural steel | 2.02 | Materials |
| work, access panels finish or field painting are in the | A. | Optional. |
| scope of work of other trades and divisions of these | A. | Door Sections: Shall be of aluminum alloy 6063-T6, | 2.07 | Windload |
| specifications. | | | 1 3/8" thick stiles and rails, joined with self tapping |
1.03 | Reference Standards | | screws | A. Windload – per DASMA 102-2003 and as required by |
| 1. Rails –Top and bottom rails with 3 1/2" wide, lower | | local codes. |
A. | ANSI/DASMA 102 – American National | | intermediate rail 1 3/8", upper rail 1 5/8" , minimum | PART III – EXECUTION |
| Standards Institute [A216.1] Specifications for sectional | | wall thickness 0.062”. |
| overhead doors published by Door & Access Systems | | 2. Stiles –Top, bottom, and end stiles are 3 1/2" wide, | 3.01 | Installation |
| Manufacturers Association International in bulletin | | center stile 3” wide, minimum wall thickness | A. | General: |
B. | 102-1990. | – Zinc [hot-dipped galvanized] | | 0.062”. | | 1. Install doors in accordance with manufacturer’s |
ASTM A123 | | 3. Glazing – 1/8" DSB (451) or 1/2" double insulated | | instructions and standards.Installation shall be by an |
C. | coatings on iron and steel products. | B. | SSB (452) | | authorizedWayne-Dalton representative. |
ASTM A216 | – Specifications for sectional overhead | Track:Track design shall be [standard lift] [high lift] | | 2. Verify that existing conditions are ready to receive |
D. | type doors. | – Steel wire, oil-tempered for | | [vertical lift] [low headroom].Vertical mounting angles | | sectional overhead door work. |
ASTM A229 | | shall be hot-dipped galvanized.Track size shall be [2"] | | 3. Beginning of sectional overhead door work means |
E. | mechanical springs. | | [3"].Vertical track shall be graduated to provide wedge | B. | acceptance of existing conditions. |
ASTM E330 | – Structural performance of exterior | | type weathertight closing with continuous angle | Install door complete with necessary hardware,jamb |
| windows, curtain walls, and doors by uniform static air | | mounting for [steel] [wood] jambs,and shall be fully | | and head mold strips,anchors,inserts,hangers,and |
| pressure difference. | | adjustable to seal door at jambs [bracket mounting for | | equipment supports in accordance with final shop |
1.04 | Quality Assurance | | wood jambs]. Horizontal track shall be reinforced with | | drawings,manufacturer’s instructions,and as specified |
| continuous angle of adequate length and gauge to | C. | herein. |
A. Sectional overhead doors and all accessories and | | minimize deflection. | Fit,align and adjust sectional overhead door assemblies |
| components required for complete and secure | Note: | Horizontal track applies to standard lift,high lift,low | D. | level and plumb for smooth operation. |
| installations shall be manufactured as a system from | Upon completion of final installation,lubricate,test and |
| one manufacturer. | C. | headroom and follow-the-roof designs only. | | adjust doors to operate easily,free from warp,twist or |
1.05 | Systems Description | Hardware:Hinge and RollerAssembly: | | distortion and fitting for entire perimeter. |
| 1. Hinges and brackets shall be made from hot- | Note: Architect may consider providing a schedule when |
A. | Sectional Overhead Door:Type: | | dipped,galvanized steel. |
B. | AFV 451/452 | | 2. Track rollers shall be case-hardened inner | | more than one sectional overhead door or opening |
Mounting: Continuous angle mounting for [steel] | | steel races with 10-ball [2"] [3"] rollers. | | type is required. |
C. | [wood] jambs [bracket mounting for wood jambs] | | 3. All factory authorized attachments shall be | 3.02 | Materials (See note above.) |
Operation: [manual push-up] [chain hoist] [motor] | D. | made at locations indicated. |
D. | [motor with chain hoist] | Counterbalance: | | |
Material:Aluminum Alloy 6063T6 [clear anodized] | | 1. Springs shall be torsion type,low-stress,helical | | |
| [acrylic enamel] | | wound,oil-tempered spring wire to provide | | |
1.06 | Submittals | | | minimum [10,000 standard] [25,000] [50,000] | | |
| | [100,000] cycles of use,on continuous steel [solid]. | | |
A. | Shop Drawings: Clearly indicate the following: | | 2. Spring fittings and drums made of die cast,high | | |
| 1. Design and installation details to withstand | | strength aluminum. | | |
| standard windload. | | 3. Pre-formed galvanized steel aircraft cable shall | | |
| 2. All details required for complete operation | | provide a minimum of a 5:1 safety factor. | | |
| and installation. | 2.03 | Operation | | |
| 3. Hardware locations. | | |
| 4. Type of metal and finish for door sections. | A. | Operation shall be [manual push-up] [chain hoist] | | |
| 5. Finish for miscellaneous components and | | [motor] [motor with chain hoist]. | | |
B. | accessories. | | Note: | Manufacturer does not recommend chain hoists or | | |
Product Data: Indicating manufacturer’s product | | |
| data, and installation instructions. | | jack shaft operators on the following track applications. | | |
1.07 | Delivery, Handling, Storage | | • 15" radius standard lift with roof pitch | | |
| less than 2:12 | | |
A. | Deliver products in manufacturer’s original containers, | | • Hi-lift less than 24" | | |
B. | dry, undamaged, seals and labels intact. | | • Hi-lift between 12" – 23" with roof pitch | | |
Store and protect products in accordance with | | less than 1:12 | | |
| manufacturer’s recommendations. | | • Low headroom track | | |
1.08 | Warranty | | | Special chain hoist assemblies (using a trolley rail) | | |
| | are available for the above track systems. | | |
A. | Provide manufacturer’s standard ONEYEAR warranty | 2.04 | Locks | | |
| against defects in workmanship and material. | | |
| | | A. | Locks shall engage the right-hand vertical track | | |
| | | | and utilize [an interior side lock] [standard size | | |
| | | | rim cylinder]. | | |
