Vizio TZEMT400AB32MAA warranty Wave Operation and Programming, Inclusion, Exclusion

Page 4

Z-Wave™ Operation and Programming

Z-Wave™ controllers from various manufacturers may support the Z-Wave™ Thermostat General V2 Device class used by the Trane Z-Wave™ Thermostat. The following procedure will allow the thermostat to be added to a Z-Wave™ network.

If you are using a controller that is not a Schlage bridge, consult the instructions that came with the controller to find out how to enroll a new device.

Inclusion

a.Hold the bridge within 6 feet (1.8 meters) of the thermostat throughout all of step 2.

Note: After you begin the enrollment process, you have 30 seconds to complete the remainder of the steps. Study the steps below before beginning.

b.Press and release the plus (+) button on the bridge.

c.Press the MENU button on the thermostat.

d.Scroll down to Z-Wave Install, and press the Select button.

e.Press the Yes button to enroll the thermostat.

f.Observe the lights on the bridge. The orange light will blink while enrollment is taking place. Enrollment is complete when the orange light becomes solid.

Exclusion

a.Hold the bridge within 6 feet (1.8 meters) of the thermostat throughout all of step 2.

Note: After you begin the enrollment process, you have 30 seconds to complete the remainder of the steps. Study the steps below before beginning.

b.Press and release the minus (-) button on the bridge.

c.Press the MENU button on the thermostat.

d.Scroll down to Z-Wave Install, and press the Select button.

e.Press the Yes button to exclude the thermostat.

f.Observe the lights on the bridge. The orange light will blink while exclusion is taking place. Exclusion is complete when the orange light becomes solid.

Inclusion and Exclusion

Inclusion or exclusion is started by putting the controller into add node or remove node state and performing the procedure outlined above. As part of the process, the thermostat sends a node information frame at normal power. Low power inclusion or low power exclusion is not possible.

4

Image 4
Contents Contents User GuideProduct Specifications TZEMT400AB32MAAWave Thermostat OverviewDisplay operation Wave Operation and Programming InclusionExclusion Inclusion and ExclusionOperation User Settings Screen ZWave InstallUsage Graph ESM SetpointsTemperature Display Thermostat Control ScreenSetpoint Display Clock DisplayThermostat Control Screen Buttons Heating Cooling Down Setpoint Setting ButtonsSetpoint Up and Down Buttons Menu Button Main Thermostat ScreenSystem Mode Screen Mode ButtonMode Operation Fan Mode Screen FAN ButtonRUN/HOLD/ESM Button Run/Hold/ESM ScreenLED Displays LED 1 Green System Operation displayMain Menu Menu SelectionDone Select Main MenuSelect Schedule SchedulesSchedules Screen Heat and Cool Schedules MondayDone Next Copy Schedule ScreenCopy Schedule Copy Monday ScheduleBack Copy Copy Schedule ScreenUser Settings User SettingsUser Settings Screen Menu optionsSet Clock Set ClockBack Set Set Clock ScreenFilter Service Filter Service Filter RuntimeService Interval 300 HRS Done ResetMaintenance Service Screen Maint Service3000 HRS Sensor Calibration SensorDone Sensor Calibration ScreenBacklite/Display Backlite Settings ScreenBacklite/Display Thermostat Info Thermostat InfoThermostat Info Screen Installer Settings Menu Hidden Screen System Settings Menu Mechanical Settings SubmenuInstaller Settings Menu Hidden Screen Fan Cycler SubmenuInstaller Settings Summary Setting Range DefaultInstaller Settings Installer Settings ScreenHvac System Connection Hvac System CompatibilityRemote Communications Multi-Stage Hvac CompatibilityStandard Gas/Electric Hvac System Wiring Installation Notes Standard Hvac System SetupHeat Pump Hvac System Wiring Installation Notes Heat Pump Hvac System SetupHvac System Operation and Setup SetupGeneral Heating and Cooling Operation Standard Hvac System TypesHeat Pump System Type Selection Changeover Type SelectionMinimum Run Time MRT Minimum Off Time MOTPower InstallationCommon or Split Transformer Systems Warranty A. and Canada Only