Charging Procedure, Switch, Swiveling Head, Repairs

the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit.

Charging Procedure

DANGER: Electrocution hazard. 120 volts present at charging terminals. Do not probe with conductive objects. Danger of electric shock or electrocution.

1.Plug the charger into an appropriate outlet before inserting battery pack.

2.Insert the battery pack into the charger. The red (charging) light will blink continuously indicating that the charging process has started.

3.The completion of charge will be indicated by the red light remaining ON continuously. The pack is fully charged and may be used at this time or left in the charger.

DW9115 (15 MINUTE CHARGER) ONLY

1.Plug the charger into an appropriate AC power outlet. The charger will beep twice and the red light will blink and then go off.

2.Insert the battery pack into the charger, making sure the pack is fully seated in the charger. The red light will blink and the charger will beep once indicating the charging process has started.

3.The battery pack will be fully charged in less than 15 minutes under most conditions. This will be indicated by the red light remaining ON and 3 audible beeps. The pack is fully charged and may be used at this time or left in the charger.

Installing and Removing the Battery Pack

To insert the power pack into your worklight, slide it into the end of the light until it snaps into place. To remove the power pack, depress the release buttons shown and withdraw the power pack.

Switch

To turn the light on, slide the switch forward. To turn it off, slide the switch back.

Swiveling Head (Fig. 1, 2)

Your worklight has a swiveling head. To convert your light to a right angle model, grasp the front end of the light forward of the switch and hold the back end firmly. Twist the front end clockwise (as viewed from the lens) until the head swivels 90 degrees and clicks into place. To return the head to a straight position, rotate the head (as viewed from the lens) counterclockwise until it clicks into the straight position.

Replacing the Light Bulb

Worklight Cat. No	Replacement Bulb Cat. No.
DW902	DW9023
DW904	DW9043
DW906	DW9063
DW908	DW9083

To replace the light bulb, first unscrew the lens holder. Pull the bulb out of the spring, and insert a new bulb. Reinstall lens holder.

NOTE: Do not look directly into the worklight beam.

Spare Bulb Storage (Fig. 3)

To store a bulb, unscrew the lens holder and remove it. Inside the body of the worklight is the storage socket. To remove the bulb, pull it up and out of the storage area.

NOTE: Removing a pack from the charger and immediately inserting it into the worklight may weaken bulb life.

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the nickel cadmium, nickel metal hydride or lithium ion batteries (or battery packs) indicate that the costs to recycle these batteries (or battery packs) at the end of their useful life

have already been paid by DEWALT. In some areas, it is illegal to place spent nickel cadmium, nickel metal hydride or lithium ion batteries in the trash or municipal solid waste stream and the RBRC program provides an environmentally conscious alternative.

RBRC™ in cooperation with DEWALT and other battery users, has established programs in the United States and Canada to facilitate the collection of spent nickel cadmium, nickel metal hydride or lithium ion batteries. Help protect our environment and conserve natural resources by returning the spent nickel cadmium and nickel cadmium, nickel metal hydride or lithium ion batteries to an authorized DEWALT service center or to your local retailer for recycling. You may also contact your local recycling center for information on where to drop off the spent battery.

RBRC™ is a registered trademark of the Rechargeable Battery Recycling Corporation.

Repairs

The charger is not serviceable. There are no serviceable parts inside the charger.

FIG. 1

LENS HOLDER			POWER PACK (NOT
LENS HOLDER		SWITCH	INCLUDED)
PORTE-LENTILLE		SWITCH	INCLUDED)
PORTE-LENTILLE	INTERRUPTEUR		ENSEMBLE DE PILES
SUJETADOR DE	INTERRUPTEUR		ENSEMBLE DE PILES
SUJETADOR DE	INTERRUPTOR		(NON COMPRIS)
LA LENTE			(NON COMPRIS)
LA LENTE			BATERIA (NO INCLUIDA)
			BATERIA (NO INCLUIDA)
BULB
AMPOULE
BOMBILLA
SWIVELING HEAD		BATTERY RELEASE BUTTON
TÊTE PIVOTANTE		BOUTON DE DÉGAGEMENT DE LA PILE
CABEZA GIRATORIA		BOTON DE LIBERACION DE LA BATERIA
FIG. 2	FIG. 3		SPARE BULB STORAGE
			RANGEMENT DE
			L’AMPOULE DE RECHANGE

COMPARTIMIENTO

PARA BOMBILLA DE

REPUESTO

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustments (including brush inspection and replacement) should be performed by a DEWALT factory service center, a DEWALT authorized service center or other qualified service personnel. Always use identical replacement parts.

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty materials or workmanship for three years from the date of purchase. This warranty does not cover part failure due to normal wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit www.dewalt.com or call 1-800-4-DEWALT (1-800-433-9258). This warranty does not apply to accessories or damage caused where repairs have been made or attempted by others. This warranty gives you specific legal rights and you may have other rights which vary in certain states or provinces.

In addition to the warranty, DEWALT tools are covered by our:

1 YEAR FREE SERVICE

DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time during the first year after purchase.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your DEWALT Power Tool, Laser, or Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt for a full refund – no questions asked. LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America, see country specific warranty information contained either in the packaging, call the local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-4-DEWALT for a free replacement.

Lampes de travail

MODÈLES DW902 (9,6 V), DW904 (12 V), DW906 (14,4 V) ET DW908 (18 V)

–Utiliser avec des ensembles de piles et des chargeurs DEWALT (vendus séparément).

POUR TOUT RENSEIGNEMENT SUR L’OUTIL OU TOUT AUTRE OUTIL

DEWALT, COMPOSER SANS FRAIS LE :

1 800 4-DEWALT (1 800 433-9258)

NOTE : La lampe de travail, modèle DW902, s’alimente à l’aide d’un ensemble de piles de 9,6 volts. La lampe de travail, modèle DW904, s’alimente à l’aide d’un ensemble de piles de 12 volts. La lampe de travail, modèle DW906, s’alimente à l’aide d’un ensemble de piles de 14,4 volts. La lampe de travail, modèle DW908, s’alimente à l’aide d’un ensemble de piles de 18 volts. Les ensembles de piles sont vendus séparément.