IRIS P522 manual Wiring to the PLUG-IN Terminals

Page 5

IRIS MODEL P522 APPLICATION MANUAL

WIRING TO THE PLUG-IN TERMINALS

Figure 1 illustrates the plug-in terminals on the rear mother board and how they are connected internally. The flame relay and self-checking relay contacts are situated together in the upper right portion of the diagram.

RF C refers to the common terminal of the flame relay, with ON being flame on, and OFF being flame off. You will note that there are two sets of contacts used for the flame relay.

SC C refers to the common terminal of the self-check- ing relay. There is only one pair of contacts used for the self-checking function. Here, the designa- tion ON refers to the self-checking taking place in a normal manner. OFF indicates a failure in the view- ing head or processor resulting from:

-the hardware (i.e. the shutter mechanism in the viewing head, or the output relay itself);

-electronic components anywhere, or internal software in the P522; or

-the power to the unit is OFF – the most likely condition.

The main power feeds in through the terminals situ- ated on the upper left side (see GND, +26V and BAT). Each designated terminal is a double terminal, or pair, so that the wiring from the power supply can be “daisy chained” from one P522 to the next without having to twist wires together into one termination.

The pair designated BAT is for battery backup, if used. Note the rectifier used internally to prevent the 26 VDC main power supply from feeding into the battery. The backup battery, if used, should be 24 volts, to ensure that the 26 VDC power feeding the P522 will not feed back into the battery. In other words, no current will flow from the battery as long as voltage of the main power supply is above that of the battery. The negative side of the battery goes to the GND terminal on the left.

Figure 1 shows how these terminals are connected inside the P522. Note the two fuses marked F1 and F2. F1 is the main power fuse for the signal proces- sor as well as the viewing head(s), and is rated at .75 Amp. Fuse F2 feeds only to the viewing head(s),

and is rated at .25 Amp. On newer units (those with NO, CAL, and YES in red letters on the front panel) these fuses are self-resetting types, and will recover from an overload automatically after power is re- moved from the P522 for 10 seconds.

The viewing head terminals (bottom right) are iden- tified as V.H. A. and V.H. B. If only one viewing head is used, you must wire to the V.H. A. termi- nals. To the left of the viewing head terminals are two terminals marked V.H. SEL (viewing head se- lector relay). Energizing this connection with 19 to 38 VDC will cause the relay on this PC board to switch to viewing head B. The nominal voltage of this relay is 24V, but the 26 VDC power circuit can be used to switch this relay, if desired.

Only the viewing head signal wire (SIG) and the sig- nal ground wire (SIG GND) are switched with this changeover relay; the 26 VDC and power ground circuit is not disturbed. Make sure that the viewing head signal wire and signal ground (braided shield in the four-conductor cable) are both connected, be- cause this ground connection is the only return path for the signal and self-checking circuit. Also, the 26 VDC used to switch this relay must be connected with the proper polarity, because the relay used is a single-side stable type. (Relays that are polarized magnetically offer increased contact force resulting in higher current-carrying capability). The two ter- minals marked V.H. SEL go directly to the relay coil.

The pair of terminals designated CHAN SEL (to the left of the V.H. SEL terminals) is used for selecting channel A or channel B on the P522. Energizing this pair of terminals causes the B channel to be se- lected. Polarity must be observed when wiring this connection (the positive terminal is on the right). This is an isolated input, so two wires are required. Any DC voltage from 7.5 to 30 may be used. The current required will depend upon the voltage, be- cause this is a photocoupler interface circuit with a 3900 ohm resistor feeding the LED light source.

For example: a 26 VDC voltage will result in a current flow of 25/3900 = .0064 Amp.

If flame is being detected and the channels are switched, the flame relay will remain energized for

Page 5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Flame Monitoring System Table of Contents Figure Index Iris Model P522 Wiring and InstallationWiring to the PLUG-IN Terminals Term Description Wiring of Viewing HeadTYP Power Supply Factory Stocked Power Supplies Redundant Power SuppliesApprovals Powering UP the P522SELF-CHECKING Function 1-9, 10 Pulses Counted DuringChecking Function SET PointsChanging SET Points Time F.F.R.T Flame Failure ResponseSighting of the Viewing Head Installation of Viewing HeadMultiple Viewing Heads Multiburner RequirementsSelecting the Pipe Installing the Viewing HeadDetermining Sight Pipe Size Mounting Hole Mounting of Sight PipeProcedures Setup and AdjustmentInitial Setup Sighting AdjustmentMultiburner Requirements Adjusting SET PointsFor Flicker Type Viewing Grounding Noise InterferenceS506 Viewing Head S509 Viewing Head S506 SELF-CHECKING Viewing HeadS512 Viewing Head S511 Viewing HeadIris Model P522 Application Manual Orificing Signal SourcesViewing Head Angle of View Viewing Head Angle View Distance and Diameter Application of Iris Viewing HeadsApplication of P522 Using a PLC with Iris FlameMonitor GAS LOW no X Burners GAS HYDROGEN, Propane and Natural GASPulverized Coal OIL Heavy OIL air & steam atomBasic Burner Start Circuit Basic Burner Start Circuit Modbus Communication Module Communications0X or Discrete Registers Setting AddressesTechnical Help Environmental Iris Model P522 Application Manual ElectricalOptical OutputsModel P522 Front Panel Model P522 Side View IR Viewing Head Location Opposed Fired Viewing Head Sighting 18, 21, 22 IndexIris Model P522 Application Manual

P522 specifications

The IRIS P522 is a highly advanced smart device characterized by its cutting-edge features, technologies, and remarkable performance capabilities. Designed for seamless integration into both personal and professional environments, the P522 stands out as a versatile tool for various applications, ranging from productivity enhancement to entertainment.

One of the main features of the IRIS P522 is its state-of-the-art display technology. The device sports a high-resolution touchscreen that provides vibrant colors and sharp images, ensuring a remarkable visual experience. This impressive display is paired with an ultra-responsive multi-touch interface, allowing users to interact effortlessly with the device, facilitating increased efficiency in tasks such as data entry, navigation, and media consumption.

The performance of the IRIS P522 is powered by a robust processor and ample RAM, enabling it to handle multitasking with ease. This ensures that users can run multiple applications simultaneously without experiencing lags or slowdowns. Additionally, the device incorporates advanced cooling technologies, which help maintain optimal operating temperatures even during intensive use, ensuring reliability over extended periods.

Connectivity is another significant aspect of the IRIS P522. Equipped with the latest wireless technologies, including Wi-Fi 6 and Bluetooth 5.0, the device allows for lightning-fast data transfer rates and seamless connections to a variety of accessories. This makes it an ideal choice for professionals who require constant communication and quick access to cloud-based resources.

Security features are paramount in today's digital landscape, and the IRIS P522 does not disappoint. It includes biometric authentication options such as fingerprint recognition and facial recognition, providing users with a secure way to access their device and data. This focus on security is further reinforced by regular software updates that ensure protection against the latest threats.

Battery life is another highlight of the IRIS P522, with an energy-efficient design that offers extended usage without frequent recharges. This is particularly beneficial for users on the go, as it enables prolonged productivity without being tethered to a power supply.

In conclusion, the IRIS P522 is a remarkable device that harmoniously blends advanced features, powerful technology, and user-centric design. With its stunning display, high performance, effortless connectivity, robust security measures, and extended battery life, the P522 caters to the needs of users in various contexts, making it an indispensable addition to modern digital life.
Top Page Image Contents