Nighthawk KN-COPP-3 Part Four What to Do When the Alarm Sounds, Common Mild Exposure Symptoms

Page 15
PHONE NUMBER

Part Four – What to Do When the Alarm Sounds

Determine if anyone in the household is experiencing symptoms of CO poisoning. Many cases of reported CO poisoning indicate that while victims are aware they are not well, they become so disoriented they are unable to save themselves by either exiting the build- ing or calling for assistance. Also young children and household pets may be the first affected. The following symptoms are related to CARBON MONOXIDE POISONING and should be discussed with ALL members of the household:

Become familiar with these common symptoms from CO poisoning.

Common Mild Exposure Symptoms:

Slight headache, nausea, vomiting, fatigue (“flu-like” symptoms).

Common Medium Exposure Symptoms:

Throbbing headache, drowsiness, confusion, fast heart rate.

Common Extreme Exposure Symptoms:

Convulsions, unconsciousness, heart and lung failure. It can cause brain damage and death.

If you experience even mild symptoms of CO poisoning, consult your doctor immediately!

!

WARNING:

Actuation of your CO Alarm indicates the presence

of Carbon Monoxide (CO) which can KILL YOU.

When the CO alarm senses a dangerous level of CO, the unit will emit a loud alarm pattern. The alarm pattern is 4 short beeps

followed by 5 seconds of silence – followed by 4 short beeps. (Note: When the unit is disconnected from the 120V power supply and is on battery backup, the alarm pattern will continue for the first 4 minutes after detecting CO and then the cycle will repeat every one minute). Know how to respond to a CO emergency. Periodically review this user’s guide and discuss with all members of your family.

If the alarm sounds:

1)Operate test/reset button;

2)Call your emergency services

PHONE NUMBER

( fire dept. or 911);

3)Immediately move to fresh air - outdoors or by an open

door/window. Do a head count to check that all persons are accounted for. Do not reenter the premises nor move away from the open door/window until the emergency services responders have arrived, the premises have been aired out, and your CO alarm remains in its normal condition.

4)After following steps 1-3, if your alarm reactivates within a 24 hour period, repeat steps 1-3 and call a quali- fied technician to investigate for sources of CO from fuel burning equipment and appliances, and inspect for

proper operation of this equipment. If problems are identified during this inspection have the equipment serviced immediately.

Note any combustion equipment not inspected by the technician and consult the manufacturer’s instructions, or contact the manufacturer’s directly, for more information about CO safety and this equipment. Make sure that motor vehicles are not, and have not been, operating in an attached garage or adjacent to the residence.

4-1

Image 15
Contents Carbon Monoxide Alarm Table of Contents Introduction About this User’s GuideQuick Set-Up Guide Setting up your CO alarm for first time operationAbout Your CO Alarm Part One Your Nighthawk CO AlarmDigital Display Nighthawk’s Unique FeaturesWhere Not to Install Your CO Alarm Where to Install Your CO AlarmWall Mounted Alarm How to Install Your AlarmDirect Plug Alarm To installNormal Operating Characteristics How to Test Your AlarmTesting the Electronics Low Battery Warning Testing the sensor responseIf the alarm malfunctions Malfunction Signal Group 1 Component FailurePeak Level Memory Button How to Know If Your Alarm is MalfunctioningHow to Care for Your Alarm To Reset the Peak Level Memory…What are the Effects of CO Exposure? What is Carbon Monoxide?Where Does CO Come From? Part Two Carbon Monoxide-The Silent KillerHome Safety Tips What You Can Do What You Should Not DoClues You Cannot See Generally 50 ppm to 100 ppm Part Three What You Should Know Before the Alarm SoundsGenerally 50 ppm and below Mid LevelsCommon Extreme Exposure Symptoms Part Four What to Do When the Alarm SoundsCommon Mild Exposure Symptoms Common Medium Exposure SymptomsTreatment for CO Poisoning Appliances has caused any change in CO alarm readingsThis determination and administer treatment if necessary Instructions on page 1-5Part Five Technical Information What happens if the power goes out? Part Six Frequently Asked QuestionsHow much electricity does it take to run the CO alarm? Flashing dot Return to zero Part Six Display Reading and What They MeanDisplay Shows Alarm Sound Unit Status Display Shows Alarm Sound Unit Status Recommended ActionPage Wall Mount Diagram Limited Warranty Warranty RegistrationPlease send products and all other correspondence to