Crown Boiler 16-325 500506 manual Typical Venting Arrangement For The Series Boiler, 2018

Page 20

9)Series 16 boilers are supplied with an external draft hood which must be installed as shown in Figure 15 without alteration. Before installing the draft hood, verify that the model number marked on the draft hood matches that of the boiler being installed. Prior to securing the draft hood verify that the distance from the top of the jacket to the bottom of the draft hood skirt matches dimension ‘E’ in Figure 1. Secure the draft hood to the boiler with at least three screws.

10)Vent pipe should slope upwards from the draft hood not less than one inch in four feet. No portion of vent pipe should run downward or have sags. Vent pipe must be securely supported.

11)Vent pipe should be installed above the bottom of the chimney to prevent blockage.

12)Vent pipe must be inserted flush with inside face of the chimney liner and the space between vent pipe and chimney sealed tight.

(OPTIONAL)

Figure 15: Typical Venting

Arrangement For The Series

16 Boiler

13)On all Series 16 boiler models install the blocked vent switch assembly to the supplied external draft hood. See Figure 16. The assembly consists of power cord and switch attached to mounting bracket and is shipped taped to the top of boiler jacket. The procedure is outlined below:

a)Untape blocked vent switch assembly from top of boiler. Uncoil power cord.

b)Position mounting bracket onto lower edge of draft hood skirt. Locate center tooth (with #10 sheet metal screw) on outside and other two teeth inside draft hood skirt. See Figure 16.

c)Slide mounting bracket tight against lower edge of draft hood skirt. Position #10 sheet metal screw above skirt's stiffening rib.

d)Secure bracket in position by tightening #10 sheet metal screw against outer surface of draft hood skirt.

e)Make sure that there is no slack in the power cord between the cable clamp on the junction box and the blocked vent switch on the draft hood.

f)Verify power cord, mounting bracket and blocked vent switch are secure and located as shown in Figure 16.

14)Do not install the optional vent damper in any portion of the vent system which is used by appliances other than the boiler being installed.

15)Vent damper installation is optional on all Series 16 model boilers. When used, install the vent damper (Figure 17) as follows:

a)Open vent damper carton and remove installation instructions. Read the instructions thoroughly before proceeding.

Verify that vent damper is same size as draft diverter outlet. See Figure 1. Unpack vent damper carefully. Do not force closed damper blade. Forcing vent damper closed may result in damaged gear train and void warranty.

2018

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Series Page Table of Contents Product DescriptionII Specifications III Before Installing IV Locating the BoilerMinimum Clearances to Combustibles Ove r a ll Im u m He ig h t Bo ile r Ro o m Knockdown Boiler Assembly Instructions Prior To AssemblyTapping Purpose Chart Boiler Shipping Arrangement With Tapping LocationsJacket Assembly 108119 1012 Gas Train Standard Build Control & Trim Installation 1412VI Air For Combustion and Ventilation 15131614 For Buildings Of Unusually Tight ConstructionAll Air From Outdoors, Ventilated Crawl Space & Attic 17151816 VII Venting 1917Typical Venting Arrangement For The Series Boiler 2018Blocked Vent Switch Installation Details 2119Removing An Existing Boiler From a Common Chimney 22202321 Viii System PipingStandard Heating System Piping 224 Standard Boiler Piping 25232624 IX Gas Piping 27252826 Control System WiringSequence of Operation Vent Damper If Used 2927 Sequence of Operation Standard Boiler WiringSequence of Operation CSD-1 Boiler Wiring Series 16 Standard Boiler Wiring 3028Series 16 CSD-1 Boiler Wiring 3129Safety Control Operation 3230XI Start-up and Checkout 33313432 Gas Valve Detail Robertshaw 7000DERHC 3533For Your Safety Read Before Lighting 36343735 XII Service and MaintenanceOn an annual basis Heat Exchanger Cleaning Procedure 3836Xiii Parts 3937Exploded View Base Parts & Manifold Base / Manifold Assembly 41394240 Base / Heat Exchanger / Flue Collector Assembly 4341Exploded View Jacket 4543 Jacket Panel CartonExploded View Trim & Control Components 4745 Control Components CartonPN980416

16-325 500506 specifications

The Crown Boiler 16-325 500506 is a highly reliable heating solution designed for residential and light commercial applications. Known for its robust construction and advanced technologies, this boiler is engineered to deliver efficient heating while ensuring longevity and minimal maintenance.

One of the standout features of the Crown Boiler 16-325 is its durable steel construction, which is essential for handling the high temperatures and pressures involved in heating systems. The boiler is typically equipped with a cast iron heat exchanger, known for its excellent heat retention and distribution capabilities. This ensures that the system heats up quickly and maintains consistent temperatures throughout the space.

The boiler's capacity to produce 325,000 BTUs makes it suitable for larger homes or commercial buildings with significant heating demands. Its high input capacity allows for effective operation in areas where traditional systems may struggle to keep up with heating requirements. The Crown Boiler 16-325 employs a forced hot water system, which circulates water through pipes and radiators, providing uniform heat and comfort in indoor spaces.

A significant technological advancement in this model is its integrated control system. The advanced control module automates burner operation, ensuring optimal performance while minimizing energy consumption. This technology not only enhances efficiency but also helps in reducing operational costs, making it a cost-effective choice for users.

Moreover, the Crown Boiler 16-325 is designed with ease of installation and maintenance in mind. It features convenient access panels that simplify the maintenance process, allowing technicians to perform service checks and repairs without extensive downtime. This attribute is particularly beneficial for property managers or homeowners looking for a hassle-free heating solution.

In terms of safety features, the boiler is equipped with a pressure relief valve and a low-water cutoff switch, ensuring safe operation while protecting against potential hazards associated with overheating or lack of water.

Overall, the Crown Boiler 16-325 500506 is a powerful and efficient heating solution that excels in durability and performance. With its advanced technologies, substantial heating capacity, and user-friendly design, it represents an excellent choice for those seeking a reliable heating system that combines efficiency with long-term operational savings.
Top Page Image Contents