White Rodgers 1F56N-911 Specifications, Installation, Select Thermostat Location

SPECIFICATIONS

ELECTRICAL DATA	APPLICATIONS
Switch Rating: 24 VAC (30 VAC max.)	The 1F56N is designed for use with
Heating - 0.15 to 1.2 Amps	• Standard heating and cooling systems
Cooling - 0 to 1.5 Amps	•	Electric heating and cooling systems
Switch Action: SPST - Snap Action	• Single stage heat pump systems
Anticipator Rating:	• Two-transformer systems
Heating - Adjustable from 0.15 to 1.2 Amps	•	Electronic air cleaners
Cooling - Fixed 24 VAC	• Humidifiers
THERMAL DATA	• Zone dampers
Temperature Range: 50°F to 90°F (10°C to 32°C)	This thermostat CANNOT BE USED with:
Differential: 1°F	•	Millivolt systems
	•	Multi-stage applications

INSTALLATION

ATTENTION: This product does not contain mercury. However, t his product may replace a unit which contains mercury.

Do not open mercury cells. If a cell becomes damaged, do not touch any spilled mercury. Wearing non-absorbent gloves, take up the spilled mercury and place into a container which can be sealed. If a cell becomes dam- aged, the unit should be discarded.

Mercury must not be discarded in household trash. When the unit this product is replacing is to be discarded, place in a suitable container and return to White-Rodgers at 2895 Harrison Street, Batesville, AR 72501-2117 for proper disposal.

SELECT THERMOSTAT LOCATION

Proper location insures that the thermostat will provide a comfortable home temperature. Observe the following general rules when selecting a location:

1.Locate thermostat about 5 ft. above the floor.

2.Install thermostat on a partitioning wall, not on an outside wall.

3.Never expose thermostat to direct light from lamps, sun, fireplaces or any temperature radiating equip- ment.

4.Avoid locations close to windows, adjoining outside walls, or doors that lead outside.

5.Avoid locations close to air registers or in the direct path of air from them.

6.Make sure there are no pipes or duct work in that part of the wall chosen for the thermostat location.

7.Never locate thermostat in a room that is warmer or cooler than the rest of the home, such as the kitchen.

8.Avoid locations with poor air circulation, such as behind doors or in alcoves.

9.The living or dining room is normally a good location, provided there is no cooking range or refrigerator on opposite side of wall.

ROUTE WIRES TO LOCATION

NOTE

All wiring must conform with local and national electrical codes and ordinances.

1.If an old thermostat being replaced is in a satisfactory location, and the wiring appears to be in good condi- tion, use existing wiring. If in doubt, re-wire.

2.If a new location is chosen or if this is a new installa- tion, thermostat wiring must first be run to the location selected.

3.Probe for obstructions in partition before drilling 1¦2” hole in wall at selected location. Take up quarter round and drill a small guide hole for sighting (see fig. 1). From basement, drill 3¦4” hole in partition floor next to guide hole. In houses without basements, drill 1¦2” hole through ceiling and into partition from above (see fig. 1).

4.Through this hole drop a light chain, or 6” chain attached to a strong cord. Snag cord in basement with hooked wire. In houses without basements, drop cord through hole in ceiling and down partitioning; snag cord at the thermostat location.

5.Attach thermostat wires to cord and pull thermostat wires through hole in wall so that 6” of wire protrudes.

1⁄2” hole for
thermostat wire
Stout cord with 6”
chain attached
Baseboard	Approximately
	5 feet from floor
strip moulding
1⁄4” guide hole
for sighting
Quarter round
removed

3⁄4” hole in floor of partition

Hooked wire for snagging chain

Figure 1. Routing thermostat wires

2