JVC SP-MD9 operating instructions Connection, Specifications

Connection

Anschluß

Raccordement

Aansluiting

Conexión

Collegamento

Ansluiting

Tilslutning

Liitäntä

Black	Press
Schwarz	Drücken
Noir	Appuyer
Zwart	Indrukken
Negro	Presionar
Nero	Premere
Svart	Tryck
Sort	Tryk
Musta	Paina

CONNECTION

•Connect the LEFT speaker terminals of the amplifier to the LEFT terminals of the speaker and RIGHT to RIGHT using the attached speaker cords as shown in the figure making sure polarity is correct; (+) to (+) and (–) to (–). Connect the black speaker wire to the (–) terminal.

•Turn off power to the whole system before connecting the speakers to the amplifier.

•The nominal impedance of the SP-MD9 is 6 ohms. Connect them to an amplifier with the load impedance of 6 ohms speak- ers.

•The maximum power handling capacity of the SP-MD9 is 50 watts. Excessive input will result in abnormal noise and pos- sible damage. In cases where the signals described below are applied to the speakers, even if the signals are below the maximum allowable input, they may cause an overload and burn the wiring of the speakers. Be sure to lower the amplifier volume beforehand.

1)Noise during FM tuning.

2)High level signals containing high frequency components produced by a tape deck in the fast forward mode.

3)Click noise produced when turning power of other compo- nents on and off.

4)Click noise produced when connecting or disconnecting cords with the power on.

5)Click noise produced when the cartridge is replaced with the power on.

6)Click noise produced when operating amplifier switches.

7)Continuous high frequency oscillation or high pitch elec- tronically produced musical instrument sound.

8)Howling when using a microphones.

1.Remove the ending part of the vinyl covering from the cut.

2.Twist the wires.

1.Entfernen Sie dan Endstück der Vinylhüle von dem geschnittenen Teil.

2.Drehen Sie die Kabel.

1.Enlever la pertie d’extrémité du recouvrement vinylique de la partie déoupée.

2.Tordre les fils.

1.Snijd het laatste gedeelte van de vinylmantel af en verwijder.

2.Draai de draadkernen ineen.

1.Quitar la parte de la extremidad de la cubierta de plástico de la parte cortada.

2.Torcer los alambres.

1.Rimuovete l’estremità della copertura in plastica dalla parte tagliata.

2.Torcete i fili.

1.Dra loss den avskurna delen av isoleringen från kabeländen.

2.Tvinna trådarna.

1.Fjern enden af vinyl-isoleringen, hvor den er klippet af.

2.Sno trådene.

1.Irrota muovipeitteen loppupää uurteesta.

2.Kierrä johdot.

SPECIFICATIONS

Type	: 3-way 3-speaker bass-reflex type
	(Magnetically-shielded type)
Speakers
Woofer	: 15 cm (5-15/16") cone x 1
Mid Range	: 6 cm (2-3/8") cone x 1
Tweeter	: 2 cm (13/16") dome x 1
Power Handling Capacity	: 50 watts
Impedance	: 6 ohms
Frequence Range	: 43 Hz-20,000 Hz
Sound Pressure Level	: 86 dB/w·m
Dimensions (W x H x D)	: 210 x 345 x 249 mm
	(8-5/16" x 13-5/8" x 9-13/16")
Mass	:3.4 kg (7.5lbs) each
Accessories	: Speaker cord ................ 2

Design and specifications subject to change without notice.

4