VENT-FREE PROPANE/LP GAS STOVE HEATER
INSTALLATION
Continued
INSTALLING GAS LOG HEATER INTO STOVE
1. | Remove log and gas log heater from |
| carton. Note: Do not pick up gas log |
| heater by the burner itself. This could |
| damage heater. Always handle the gas |
| log heater by the heater base only. |
2. | Remove all protective packaging applied |
| to log and gas log heater for shipment. |
7. Fasten heater base to stove bottom with |
vided with gas log heater (see Figure |
14). Attachment hardware is factory |
packed inside plastic bag with installa- |
tion manual and owner’s registration |
card. Push bolt through heater base |
mounting hole and through stove bot- |
tom. Connect hex nut to bolt on under- |
side of stove bottom. The bolt hex head |
is for a 5/16" socket and the hex nuts |
are for a 3/8" socket. If sockets are not |
available, use adjustable wrenches. |
|
|
|
| Heater |
Bolt |
|
| Base | |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Stove |
Hex Nut |
|
|
|
|
| ||
|
|
| |||||
|
|
| |||||
|
|
|
|
| Bottom | ||
|
|
| |||||
|
|
|
| ||||
|
|
|
| ||||
|
|
|
|
|
|
|
|
Figure 14 - Fastening Heater Base to Stove Drop Bottom
3. | Check all items for any shipping dam- |
| age. If damaged, promptly inform |
| dealer where you bought heater. |
4. | If not already removed, remove back |
| panel from assembled stove body (see |
| Figure 5, page 8). Use an adjustable |
| wrench or a 10 mm socket. Remove six |
| (6) bolts and washers. Keep bolts and |
| washers to reattach back panel later. |
5. | Set gas log heater inside stove (see Fig- |
| ure 13). Make sure control knob exten- |
| sions pass through bottom front opening. |
6. | Align outside holes on heater base with |
| four (4) mounting holes on the stove |
| bottom (see Figure 13). |
8. | Set |
| shown in Figure 15. Make sure middle |
| section at bottom of log is seated into |
| "U" shaped cutout in center of heater |
| base. Log will fit securely on base. |
| IMPORTANT: Make sure log does not |
| cover any burner ports and does not |
| touch the stove cavity (see Figure 16). |
9. | Fasten back panel to stove with six (6) |
| M6 x 1.20mm bolts and washers. Make |
| sure product identification label is located |
| on the outside lower |
10. | Place freestanding stove in desired po- |
| sition in room. Be sure to maintain |
| clearances to combustibles as outlined |
| on page 7. |
LO
Heater
Base
Log Set
Middle
Section at
Bottom of
Log Set
Burner
"U" Shaped
Cutout in
Chassis
Burner
Bottom
Front
Opening
Bolt |
| |
Heater | Stove | |
Bottom | ||
Base | ||
|
Figure 13 - Placing Heater Base In Stove Cavity (Appearance May Vary Depending on Model)
Figure 15 - Installing One-Piece Stove Log Set
Burner Porting Areas (double slotted rectangular openings
Safety Pilot Location | ||
Log Set | ||
|
Figure 16 - Top View of One-Piece Log Set on Gas Log Heater
10 | 104464 |