Dialer Capture Module Information
LED Indicator | STATUS |
|
|
RED – Steady ON | Messages exist in buffer. |
|
|
RED – Flashing | No messages to be sent. Waiting for messages. |
|
|
GREEN – Steady ON | Normal Indication. |
|
|
GREEN – Blinks every 2 sec. | PowerBoost1 communication problem. |
|
|
GREEN – Blinks twice every sec. | Communication Module connection is lost. |
|
|
GREEN – Blinks 10 times every sec. | PowerBoost1 and Communications Module connection is lost. |
|
|
EOL
Telco 2 Telco 1 EOL
ZN-
ECP
Ring 2
Tip 2
ZN+ PWR GND Tip 1 Ring 1 | Data Out Data In 12V In GND |
| RED |
GREEN
Dialer Capture Module
Note: Telco ports 1 (primary dialer) and 2 (secondary dialer) may be used instead of the terminal board.
Whichever connection method is used, both Telco paths must be connected to the Fire Panel.
LED Display Information
| Panel Status |
| LED Indicator |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| RADIO TROUBLE | Yellow – ON when radio trouble is present. | RADIO TROUBLE |
|
|
|
| ||||
|
|
|
|
| |||||||
|
|
|
|
| |||||||
|
|
| ∙ Both IP and GSM communication paths are lost. |
|
|
| |||||
|
|
|
|
|
|
|
|
|
| ||
|
|
| ∙ Communicator radio is not registered. | zzeru |
|
|
|
|
|
| |
|
|
| ∙ Old Alarm Time has been exceeded. (Message has not been |
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| ||
|
|
| delivered within the fixed 10 minute window.) | b |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| |
|
|
| Buzzer – Upon loss of AC power, this will beep once every 10 |
|
|
|
|
|
|
| |
|
|
| LOW BATTERY |
|
|
|
|
| |||
|
|
| seconds. |
|
|
|
|
| |||
|
|
| (not used) |
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| ||
| LOW BATTERY | Yellow – ON when battery is low (<11.5VDC). |
|
|
|
|
| ||||
|
|
|
|
|
| ||||||
|
|
|
|
| AC LOSS |
|
|
|
|
| |
|
|
| Yellow – (not used) |
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| ||
| AC LOSS |
| Yellow – ON when no AC is present (< 90VAC). | AC ON |
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |||
| AC ON |
| Green – ON when AC is present. |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
Note: If a wire pulled out of the LED Board Connector refer to the diagram on right and reinsert wire, ensuring the connector pin is locked in.
Violet |
|
| LED Board | ||
|
| ||||
Black |
|
| |||
|
| Connector | |||
White |
|
| |||
| NC | Wires | |||
Red |
|
|
| ||
|
| NC |
| ||
|
|
|
|
| |
Brown |
| ||||
|
| ||||
Yellow |
|
| |||
|
| ||||
Gray |
|
|
|
| |
|
|
|
| ||
|
|
| |||
|
|
|
|
|
|
– 10 –