Honeywell IPGSM-DPC manual PowerBoost1

Page 7

IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide

4.Connect the LED Display board to its connector, then slide the board into the mounting rails. (Refer to the “LED Display Information” topic if a wire is detached from its connector.)

5.Carefully remove the packaging material that surrounds the PowerBoost1.

6.Mount the PowerBoost1 on the three unused standoffs. Use the plastic screw (prevents shorting) to secure the upper right corner of the PowerBoost1 and the two metal screws and lock washers to fasten the left side of the circuit board. Ensure the lock washers are located between the circuit board and the head of the two metal screws.

7.Use the 1451-UL9 Wired Transformer directly connected to un-switched facility power. Connect and route 14AWG (minimum) insulated wire from facility ground to the 1451-UL9 enclosure ground post and through the conduit to the IPGSM-DPC cabinet ground post.

8.Route 16AWG wire from the transformer secondary, through the conduit. Pass the wires through the Ferrite Filter, then loop the wires back through again making a loop. (Ensure the wire ends that connect to the PowerBoost1 Module are tinned.) Connect the wires to the PowerBoost1 AC terminals. At this time DO NOT apply power.

9.Ensure all ground connections are tight.

10.Connect the Ethernet cable and the Telco 1 and Telco 2 lines. If you choose to use an optional Cabinet Tamper Switch (if the control panel supports it) mount and wire it.

Note: The Ethernet cable, Telco 1, Telco 2 lines, and the optional cabinet Tamper Switch (if used) must be run through conduit.

11.Verify the PowerBoost1 module DIP switches are configured as shown below.

PowerBoost1

-V0

ON

 

 

 

 

 

 

 

 

 

008-COM-iPGSM

1

2

3

4

5

ON

1 2 3 4 5

(Switch handle = white)

12.Ensure the following:

∙LED Display board is fully seated.

∙All wiring terminals and connectors are tight.

∙All wiring has been completed and secured with cable ties.

13.Install the battery (not supplied). Apply power to the 1451-UL9 Wired Transformer, and attach the battery cable.

– 5 –

Page 6 Page 8
Image 7
Page 6 Page 8
Contents IPGSM-DPC Contents General Information Package ContentsCompatible Fire Panels Operation ULC Compliance InstallationSetup the Customer Account Register the Communications Module with AlarmNetMount and Wire Determine the Signal Strength and Select a LocationPowerBoost1 Wiring for Grounds, Power, and RF Wiring the 659EN Line Fault Monitor if required 7720P Programmer Program the Communications ModuleTest the System Configure the Fire PanelLED Display Information Dialer Capture Module InformationTrouble PowerBoost1 Module InformationGRN IGSM Communications Module InformationCentral Station Messages RF SpecificationsIPGSM-DPC Trouble Detection Information IPGSM-DPC SpecificationsPage Page Page Page Page Page Battery Ê800-093708Š

IPGSM-DPC specifications

The Honeywell IPGSM-DPC is an advanced communication device designed for alarm systems, providing a reliable and robust connection to monitoring services. This dual-path communicator integrates both internet and cellular technologies, ensuring that security alarm signals are transmitted without interruption. Its ability to utilize both pathways enhances the reliability of the alarm signals, especially in situations where one mode of communication might fail.

One of the standout features of the IPGSM-DPC is its compatibility with Honeywell's Total Connect service, which allows users to remotely monitor and manage their security systems via a smartphone, tablet, or computer. This feature provides real-time alerts and updates, giving users peace of mind and control over their security environment. With Total Connect, users can also receive notifications for certain events like alarm triggers or system status changes.

The IPGSM-DPC is built with the latest in wireless communication technology. It operates on the LTE (Long-Term Evolution) network, which ensures fast data transmission speeds and a wider coverage area. Additionally, the device supports multiple communication formats, making it flexible and adaptable to various alarm panel configurations. This versatility allows for easy integration into existing security systems without the need for extensive rewiring or hardware replacements.

Moreover, the Honeywell IPGSM-DPC features a built-in backup battery, ensuring continued operation even in the event of a power outage. This added layer of security is crucial for maintaining protection during emergencies. The device is designed with user-friendly installation in mind, allowing both professionals and DIY users to set it up quickly and efficiently.

Another notable characteristic is its robust encryption methods, which protect data during transmission. This ensures that sensitive information related to security alarms remains secure from potential cyber threats. The IPGSM-DPC is also equipped with diagnostic features, allowing users to monitor the health and performance of their communication paths, helping to preemptively address any connectivity issues.

In summary, the Honeywell IPGSM-DPC is a state-of-the-art dual-path communicator that enhances the reliability and security of alarm systems. With its integration capabilities, robust cellular technology, user-friendly installation process, and advanced security features, it stands out as an essential component for modern security solutions. Whether used in residential or commercial applications, it offers peace of mind and advanced control over alarm systems.
Top Page Image Contents