Honeywell IPGSM-DPC manual IGSM Communications Module Information, Grn

Page 14

IPGSM-DPC Commercial Fire Communicator – Installation and Setup Guide

iGSM Communications Module Information

ON – NOT registered with AlarmNet.

GRN

OFF – Registered with AlarmNet.

 

 

 

FAST BLINK – Download session with Compass

 

 

 

in progress.

 

 

 

SLOW BLINK – In unison with yellow LED,

 

 

 

registration in progress.

 

 

 

 

 

 

 

ON – Message transmission pending.

YEL

QUICK PERIODIC BLINK – Normal.

 

 

 

 

 

 

FAST BLINK – Message waiting for network ACK.

 

 

 

SLOW BLINK – Idle power abnormal.

 

 

 

SLOW BLINK – In unison with green LED,

 

 

 

registratration in progress.

 

 

 

 

 

 

 

ON – No contact with network.

RED

OFF – Normal.

 

 

 

 

 

 

SLOW BLINK – Loss of communication with the

 

 

 

Dialer Capture Module (ECP fault).

 

 

 

FAST BLINK – No network contact AND loss of communi-

 

 

 

cation with the Dialer Capture Module.

 

 

 

Note: If all LEDs FAST BLINK in unison with

the RSSI LEDs this indicates a Hardware Error.

7720P

PRIMARY POWER: 9 - 16.5 VAC

 

CURRENT: 900mA PEAK, 70mA STANDBY

 

BATTERY: 8V. 3.1 AHr FOR 24 Hr BACKUP

Programmer

 

 

Port

FCC:XXXXXXXXXX IC: YYYYYYYYYY

 

TB 1

 

 

1

 

RSSI / Mode

2

 

 

and

3

 

 

status LEDs

4

GPRS M1 M0 RSSI

IBS

5

Tamper

 

6

 

7

Switch

Mode

8

 

Switch

9

 

 

10

 

 

11

 

 

ON – 100 MB/S link to Internet.

Link Speed

 

 

OFF – 10 MB/S link to Internet.

GREEN

 

 

 

 

 

 

ON – Ethernet Link detected.

Ethernet Link/Activity

 

 

OFF – No link detected.

 

 

GREEN

 

 

 

 

FAST BLINK – Transmitting/Receiving Data.

 

 

 

 

 

 

 

 

 

MODULE'S RECEIVED SIGNAL STRENGTH (RSSI)

When the Mode Switch is NOT depressed, LED 1 will illuminate red.

The remaining LEDs indicate RSSI (Received Signal Strength).

MODULE'S OPERATION MODE

When the Mode Switch IS depressed, LED 1 will be OFF.

LEDs 2 and 3 indicate the module's communication mode with the Dialer Capture Module.

 

Mode

LED 2 (yellow)

LED 3 (yellow)

 

 

 

 

 

 

 

ECP

OFF

OFF

 

 

 

 

 

 

Zone (NOT USED)

ON

OFF

 

 

4204 (NOT USED)

OFF

ON

 

 

 

 

 

 

2 - 4204 (NOT USED)

ON

ON

 

 

 

 

 

iPGSM-DPC-012-V0

MODULE'S STATUS

When the Mode Switch IS depressed, LED 1 will be OFF.

LEDs 4, 5, and 6 indicate the module's Status.

LED 4 (green)

LED 5 (green)

LED 6 (green)

 

 

 

ON - Connected to

ON - GPRS service

ON - Module registered, no second

Internet.

available.

site available.

OFF - Not connected

OFF - No GPRS service

OFF - Module not registered with

to Internet.

available

network carrier.

 

FAST BLINK - GPRS in

SLOW BLINK - Module registered, second

 

use.

site available, and low signal strength.

 

 

NORMAL BLINK - Module registered, second

 

 

site available, acceptable signal strength.

 

 

FAST BLINK - Module registered, second

 

 

site available, excellent signal strength.

 

 

 

12

Image 14
Contents IPGSM-DPC Contents Compatible Fire Panels Package ContentsGeneral Information Operation Register the Communications Module with AlarmNet InstallationSetup the Customer Account ULC ComplianceDetermine the Signal Strength and Select a Location Mount and WirePowerBoost1 Wiring for Grounds, Power, and RF Wiring the 659EN Line Fault Monitor if required Program the Communications Module 7720P Programmer Configure the Fire Panel Test the SystemDialer Capture Module Information LED Display InformationPowerBoost1 Module Information TroubleIGSM Communications Module Information GRNRF Specifications Central Station MessagesIPGSM-DPC Specifications IPGSM-DPC Trouble Detection InformationPage Page Page Page Page Page Battery Ê800-093708Š