Grizzly G0690, G0691 owner manual Belt Tension Replacement, Tensioning Belt, Replacing Belt

Page 75

Belt Tension &

Replacement

The three V-belts stretch slightly as the saw is used. Most of the belt stretching will happen dur- ing the first 16 hours of use, but it may continue in small increments through continued use.

Tools Needed

Qty

Wrenches 18mm

................................................ 2

Tensioning Belt

1.DISCONNECT THE SAW FROM POWER!

2.Lower the blade completely, then open the motor cabinet.

3.Loosen the hex nuts on the motor shown in Figure 126, and pivot the motor up and down to make sure that it is movable.

V-Belts

Hex Nut

(Not Shown)

Hex Nut

Figure 126. Motor mounting nut.

4.Press down on the motor with one hand to keep the belt tension tight and tighten the hex nuts.

5.Press each V-belt in the center to check belt tension.

The belts are correctly tensioned when there is approximately 1⁄2" deflection when they are pushed with moderate pressure, as shown in

Figure 127.

EjaaZn

1⁄2"

9Z[aZXi^dc

EjaaZn

Figure 127. Checking belt tension.

—If there is more than 1⁄2" deflection when the V-belts are pushed with moderate pres- sure, loosen the hex nuts, adjust the motor downward, then tighten the hex nuts.

6.Close the motor access cover.

Replacing Belt

1.DISCONNECT THE SAW FROM POWER!

2.Lower the blade completely, then open the motor access cover.

3.Loosen the hex nuts that secure the motor (see Figure 126) and raise the motor fully to remove tension on the V-belts. Roll the V-belts off of the arbor and motor pulleys.

4.While continuing to raise the motor, install a new matching set of V-belts onto the pulleys, lower the motor to tension the V-belts, then tighten the hex nuts.

5.Follow Step 5 in the Tensioning Belt sub- section to check V-belt tension.

6.Close the motor access cover.

Model G0690/G0691 (Mfg. 11/10+)

-73-

Page 74 Page 76
Image 75
Page 74 Page 76
Contents Cabinet Table SAW Ss ,EAD from Leadbased PAINTS Table of Contents NdjgBVXcZ IntroductionManual Accuracy Contact Info Machine DescriptionTube IdentificationFront Rail Scale$&+,1$7$ Miter Gauge Information Other Specifications 546 lbs 74-3/4 Other Specifications Safety Instructions for Machinery SafetyZghWZXdbZVYhigVXidc# Children & BYSTANDERS. @ZZe XaYgZcCutting Correct MATERIAL. CZkZg Xji Additional Safety for Table SawsPreventing Kickback Protecting Yourself From KickbackBelow are tips to avoid the most common causes of kickback Glossary of Terms Circuit Information Power SupplyAvailability Full-Load Current Rating50 ft Grounding InstructionsExtension Cords Minimum Gauge Size 12 AWGDescription Qty SetupItems Needed for Setup UnpackingHardware Recognition Chart Hex Wrench Set Eight Pieces 1.5-8mm Box Contents Figures QtyInventory CZcihdjiidckZcidgniZb#Fence Inventory G0690 Components QtyHardware and Tools Not Shown Qty  EjidchVZin\aVhhZh# CleanupBefore cleaning, gather the following ™ 9hedhVWaZGV\h Basic steps for removing rust preventativeSite Considerations To assemble the table saw AssemblyExtension wings installed Page G0691 Extension Table G0690 Extension TableMagnetic Switch Fence & Miter GaugeSaw Blade Fence Scale Checking Fence ParallelismBlade Guard To install the fence scaleDust Collection Power ConnectionConnecting Power Disconnecting PowerTo test run the machine Recommended AdjustmentsAdjustments that should be verified Test RunOperation Overview OperationsThrough Cuts Basic ControlsNon-Through Through Cuts Non-Through CutsBlade Selection Ripping Blade FeaturesWorkpiece Inspection Blade RequirementsCrosscut blade features Laminate blade features Combination blade featuresDado Blades To install the blade Blade InstallationBlade Guard Assembly SpreaderAnti-Kickback Pawls When Not to Use the Blade Guard When to Use the Blade GuardRiving Knife How to Install the Riving KnifeWhen to Use the Riving Knife When Not to Use the Riving KnifeTypical ripping operation RippingTo make a crosscut using the miter gauge Crosscutting Miter CutsTo perform a miter cut Installing a Dado Blade Blade Tilt/Bevel CutsDado Cutting Finished Dado Cut Cutting Dadoes with a Dado BladeCut 2 Blade Cutting Dadoes with a Standard BladeTo use a standard saw blade to cut dadoes Ut 1 Blade7aVYZ8jiDji Rabbet CuttingCutting Rabbets with a Dado Blade ZcXZCutting Rabbets with a Standard Blade To cut rabbets with the standard bladeBlade Components Needed for Resaw Barrier ResawingMaking Resaw Barrier Tools Needed QtyResawing Operations Auxiliary FenceLdg`eZXZ Front ViewGZhVl ZcXZ 7VggZg Shop Made Safety Accessories FeatherboardsMaking a Featherboard Now, proceed to Mounting Featherboard in Miter Slot on Assembling miter slot featherboard ComponentsMounting Featherboards w/Clamps Mounting Featherboard in Miter SlotFeatherboard ⁄ 2 Grid Using a Push StickPush Sticks Making a Push StickUse this template to make your own push block Using a Push BlockPush Blocks Making a Push BlockMaterial Needed for Push Block Making a Narrow-Rip Push Block for an Auxiliary FenceMaterial Needed for Narrow Rip Auxiliary Fence & Push BlockKeep the blade guard installed Using the Auxiliary Fence and Push BlockOutfeed & Support Tables Crosscut SledSupport Outfeed Aftermarket Accessories from Grizzly G7314Z-Heavy-Duty Mobile BaseG8684Z-Extension Kit for Shop Fox Mobile Bases T10222-Router Table Attachment T10223T10222Forrest Dado Blades G1317-37 Wide Outfeed Roller System H3309-Shop Fox FeatherboardT20916-Zero Clearance Insert for G0690-91 T20392-Success with TablesawsMaintenance CleaningSchedule Lubrication Worm Gears, Trunnion and Bearing Housing TeethService TroubleshootingSymptom Possible Cause Possible Solution Symptom Possible Cause Possible Solution Blade Tilt Stops Setting 90 Stop BoltStop Bolt Jam Nut Setting 45 Stop BoltAdjustable Square To adjust the blade parallel to the miter slotMiter Slot to Blade Parallelism Adjusting Alignment Spreader or Riving Knife AlignmentChecking Alignment Follow Checking Alignment, Steps Fence AdjustmentsAdjusting Bent Spreader/Riving Knife Square and Height7gVX`Zi Clamping Pressure and ParallelismFence Scale Calibration To calibrate the fence scale indicator win- dowsTo adjust the miter bar tightness Miter Gauge AdjustmentsChecking/Setting 90 Stops Adjusting Miter Bar TightnessBelt Tension Replacement Tensioning BeltReplacing Belt XdbedcZcih# WiringWiring Safety Instructions Shock HAZARD. Ldg`c\dclgc\iVihXdcCapacitor Model G0690/G0691 Wiring DiagramMagnetic switch StartTable Saw Body Breakdown PartsDescription Table Saw Body Parts ListTrunnion Assembly Breakdown Trunnion Assembly Parts List Bull Gear Description Blade Guard BreakdownMiter Gauge Breakdown Fence Breakdown Model G0690 Extension Table Breakdown Model G0691 Extension Table Breakdown Labels and Cosmetic Parts Breakdown 10. 8dbbZcih 99.$5342!, .# 0//88 %,,.!- 7!  EaVXZ HiVbe =ZgZWarranty and Returns Order Hours a DAY
Related manuals
Manual 80 pages 18.77 Kb Manual 11 pages 16.47 Kb

G0690, G0691 specifications

The Grizzly G0691 is a remarkable cabinet table saw designed for both hobbyists and professional woodworkers seeking precision and reliability. With its robust construction and advanced features, it stands out in the woodworking industry, making it a popular choice among serious craftspeople.

One of the key features of the G0691 is its powerful 3 HP motor, capable of delivering the performance needed for even the most demanding tasks. This motor can handle various materials, from softwoods to hardwoods, ensuring smooth, clean cuts every time. The saw's electronic variable speed control also allows users to adjust the blade speed according to the type of material being cut, providing flexibility and versatility in woodworking projects.

The G0691 boasts a heavy-duty cast iron table, which offers exceptional stability and supports larger workpieces. The table measures 27 inches by 40 inches, providing ample workspace for cutting. The potential for expansion is also present, as the saw is designed to accommodate extension wings for added surface area, making it easier to manage larger materials.

An impressive feature of the G0691 is its premium fence system. The T-square design ensures accurate measurements and smooth adjustments, enabling woodworkers to achieve precise cuts. This system includes a quick-release lever for easy adjustments, allowing for efficiency during the workflow.

Safety is another priority with the Grizzly G0691. The saw is equipped with a smart blade-guard system designed to offer maximum visibility while protecting the user from accidental contact with the blade. Additionally, the riving knife technology significantly reduces the likelihood of kickback, enhancing safety during operations.

The G0691's dust collection system is integrated to minimize debris, creating a cleaner workspace. The system is designed to connect easily to standard dust collection hoses, allowing for effective removal of sawdust and other waste materials.

In summary, the Grizzly G0691 combines power, precision, and safety into an exceptional cabinet table saw. Its durable construction, advanced fence system, effective dust collection, and user-friendly features make it an ideal option for both seasoned professionals and dedicated hobbyists. The investment in this tool is justified by its performance, ensuring it stands out as a valuable addition to any woodworking setup.
Top Page Image Contents