Grizzly G0690, G0691 Fence Adjustments, Adjusting Bent Spreader/Riving Knife, Square and Height

Page 71

3.Loosen the two cap screws on the mounting block, then adjust either the top or bottom control set screws or side control set screws (see Figure 116) to move it the needed direc- tion.

Center

 

Cap

 

S

Screw

 

Screws

 

 

 

Set Screw

6a^\cbZci

 

 

OdcZ

Adjustment Block

B^hVa^\cZY

Ide8dcigda

H^YZ 8dcigda

H^YZ 8dcigda

Hea^iiZgdg

G^k^c\@c^[Z

 

7aVYZ

7diidb8dcigda

Figure 116. Set screws for adjusting spreader/

riving knife position.

Top and Bottom Control: To move the top of the spreader/riving knife right or left (and the bottom of the spreader/riving knife in the opposite direction), adjust the top and bottom pair of set screws on the mounting block an equal amount in the opposite direction.

Side Control: To move the front of the spreader/riving knife left or right (and the rear of the spreader/riving knife in the opposite direction), adjust each pair of side control set screws an equal amount in the opposite direction.

Note: To adjust how tightly the mounting block holds the spreader/riving knife, adjust the center screw.

4.Reinstall the table insert.

Model G0690/G0691 (Mfg. 11/10+)

5.Follow Checking Alignment, Steps 1–3.

—If the spreader/riving knife is in the align- ment zone, no additional steps are neces- sary.

—If the spreader/riving knife is still not in the alignment zone, continue adjusting the set screws on the mounting block as neces- sary to correctly position the spreader/ riving knife.

6.Tighten the two cap screws on the mount- ing block to secure the spreader/riving knife adjustment.

Adjusting Bent Spreader/Riving Knife

1.DISCONNECT THE SAW FROM POWER!

2.Bend the spreader or riving knife by hand while installed, then follow Steps 1–3in Checking Alignment to determine if it is par- allel with the blade and inside the "Alignment Zone" (refer to Checkitng Alignment).

—­If this doesn't work, remove it to straight- en.

—If you cannot straighten it properly, replace it.

Fence Adjustments

There are four main adjustments for the fence: square, height, parallelism, and clamping pres- sure. Keep in mind that these adjustments are interconnected and some trial-and-error may be needed to achieve satisfactory results.

Tools Needed

Qty

Hex Wrench 6mm

1

Square

1

Felt-Tipped Marker

1

Square and Height

The fence face must be square to the table in order to produce square cuts. Also, the fence should be adjusted high enough off the table that it does not drag across the surface.

-69-

Page 70 Page 72
Image 71
Page 70 Page 72
Contents Cabinet Table SAW Ss ,EAD from Leadbased PAINTS Table of Contents NdjgBVXcZ IntroductionManual Accuracy Contact Info Machine DescriptionTube IdentificationFront Rail Scale$&+,1$7$ Miter Gauge Information Other Specifications 546 lbs 74-3/4 Other Specifications Safety Instructions for Machinery SafetyZghWZXdbZVYhigVXidc# Children & BYSTANDERS. @ZZe XaYgZcCutting Correct MATERIAL. CZkZg Xji Additional Safety for Table SawsBelow are tips to avoid the most common causes of kickback Preventing KickbackProtecting Yourself From Kickback Glossary of Terms Circuit Information Power SupplyAvailability Full-Load Current Rating50 ft Grounding InstructionsExtension Cords Minimum Gauge Size 12 AWGDescription Qty SetupItems Needed for Setup UnpackingHardware Recognition Chart Hex Wrench Set Eight Pieces 1.5-8mm Box Contents Figures QtyInventory CZcihdjiidckZcidgniZb#Hardware and Tools Not Shown Qty Fence Inventory G0690Components Qty  EjidchVZin\aVhhZh# CleanupBefore cleaning, gather the following ™ 9hedhVWaZGV\h Basic steps for removing rust preventativeSite Considerations To assemble the table saw AssemblyExtension wings installed Page G0691 Extension Table G0690 Extension TableSaw Blade Magnetic SwitchFence & Miter Gauge Fence Scale Checking Fence ParallelismBlade Guard To install the fence scaleDust Collection Power ConnectionConnecting Power Disconnecting PowerTo test run the machine Recommended AdjustmentsAdjustments that should be verified Test RunOperation Overview OperationsThrough Cuts Basic ControlsNon-Through Through Cuts Non-Through CutsBlade Selection Ripping Blade FeaturesWorkpiece Inspection Blade RequirementsDado Blades Crosscut blade features Laminate blade featuresCombination blade features To install the blade Blade InstallationAnti-Kickback Pawls Blade Guard AssemblySpreader When Not to Use the Blade Guard When to Use the Blade GuardRiving Knife How to Install the Riving KnifeWhen to Use the Riving Knife When Not to Use the Riving KnifeTypical ripping operation RippingTo perform a miter cut To make a crosscut using the miter gaugeCrosscutting Miter Cuts Dado Cutting Installing a Dado BladeBlade Tilt/Bevel Cuts Finished Dado Cut Cutting Dadoes with a Dado BladeCut 2 Blade Cutting Dadoes with a Standard BladeTo use a standard saw blade to cut dadoes Ut 1 Blade7aVYZ8jiDji Rabbet CuttingCutting Rabbets with a Dado Blade ZcXZBlade Cutting Rabbets with a Standard BladeTo cut rabbets with the standard blade Components Needed for Resaw Barrier ResawingMaking Resaw Barrier Tools Needed QtyResawing Operations Auxiliary FenceGZhVl ZcXZ 7VggZg Ldg`eZXZFront View Making a Featherboard Shop Made Safety AccessoriesFeatherboards Now, proceed to Mounting Featherboard in Miter Slot on Assembling miter slot featherboard ComponentsFeatherboard Mounting Featherboards w/ClampsMounting Featherboard in Miter Slot ⁄ 2 Grid Using a Push StickPush Sticks Making a Push StickUse this template to make your own push block Using a Push BlockPush Blocks Making a Push BlockMaterial Needed for Push Block Making a Narrow-Rip Push Block for an Auxiliary FenceMaterial Needed for Narrow Rip Auxiliary Fence & Push BlockKeep the blade guard installed Using the Auxiliary Fence and Push BlockSupport Outfeed Outfeed & Support TablesCrosscut Sled G8684Z-Extension Kit for Shop Fox Mobile Bases Aftermarket Accessories from GrizzlyG7314Z-Heavy-Duty Mobile Base Forrest Dado Blades T10222-Router Table AttachmentT10223T10222 G1317-37 Wide Outfeed Roller System H3309-Shop Fox FeatherboardT20916-Zero Clearance Insert for G0690-91 T20392-Success with TablesawsSchedule MaintenanceCleaning Lubrication Worm Gears, Trunnion and Bearing Housing TeethSymptom Possible Cause Possible Solution ServiceTroubleshooting Symptom Possible Cause Possible Solution Blade Tilt Stops Setting 90 Stop BoltStop Bolt Jam Nut Setting 45 Stop BoltMiter Slot to Blade Parallelism Adjustable SquareTo adjust the blade parallel to the miter slot Checking Alignment Adjusting AlignmentSpreader or Riving Knife Alignment Follow Checking Alignment, Steps Fence AdjustmentsAdjusting Bent Spreader/Riving Knife Square and Height7gVX`Zi Clamping Pressure and ParallelismFence Scale Calibration To calibrate the fence scale indicator win- dowsTo adjust the miter bar tightness Miter Gauge AdjustmentsChecking/Setting 90 Stops Adjusting Miter Bar TightnessReplacing Belt Belt Tension ReplacementTensioning Belt XdbedcZcih# WiringWiring Safety Instructions Shock HAZARD. Ldg`c\dclgc\iVihXdcCapacitor Model G0690/G0691 Wiring DiagramMagnetic switch StartTable Saw Body Breakdown PartsDescription Table Saw Body Parts ListTrunnion Assembly Breakdown Trunnion Assembly Parts List Bull Gear Description Blade Guard BreakdownMiter Gauge Breakdown Fence Breakdown Model G0690 Extension Table Breakdown Model G0691 Extension Table Breakdown Labels and Cosmetic Parts Breakdown 10. 8dbbZcih 99.$5342!, .# 0//88 %,,.!- 7!  EaVXZ HiVbe =ZgZWarranty and Returns Order Hours a DAY
Related manuals
Manual 80 pages 18.77 Kb Manual 11 pages 16.47 Kb

G0690, G0691 specifications

The Grizzly G0691 is a remarkable cabinet table saw designed for both hobbyists and professional woodworkers seeking precision and reliability. With its robust construction and advanced features, it stands out in the woodworking industry, making it a popular choice among serious craftspeople.

One of the key features of the G0691 is its powerful 3 HP motor, capable of delivering the performance needed for even the most demanding tasks. This motor can handle various materials, from softwoods to hardwoods, ensuring smooth, clean cuts every time. The saw's electronic variable speed control also allows users to adjust the blade speed according to the type of material being cut, providing flexibility and versatility in woodworking projects.

The G0691 boasts a heavy-duty cast iron table, which offers exceptional stability and supports larger workpieces. The table measures 27 inches by 40 inches, providing ample workspace for cutting. The potential for expansion is also present, as the saw is designed to accommodate extension wings for added surface area, making it easier to manage larger materials.

An impressive feature of the G0691 is its premium fence system. The T-square design ensures accurate measurements and smooth adjustments, enabling woodworkers to achieve precise cuts. This system includes a quick-release lever for easy adjustments, allowing for efficiency during the workflow.

Safety is another priority with the Grizzly G0691. The saw is equipped with a smart blade-guard system designed to offer maximum visibility while protecting the user from accidental contact with the blade. Additionally, the riving knife technology significantly reduces the likelihood of kickback, enhancing safety during operations.

The G0691's dust collection system is integrated to minimize debris, creating a cleaner workspace. The system is designed to connect easily to standard dust collection hoses, allowing for effective removal of sawdust and other waste materials.

In summary, the Grizzly G0691 combines power, precision, and safety into an exceptional cabinet table saw. Its durable construction, advanced fence system, effective dust collection, and user-friendly features make it an ideal option for both seasoned professionals and dedicated hobbyists. The investment in this tool is justified by its performance, ensuring it stands out as a valuable addition to any woodworking setup.
Top Page Image Contents