HA40 4-Channel Controller
1
S2
1
RS-R85 / ETHERNET OPTION
U3
U2
P1
*SENSOR INPUT OPTION
Combination
Dual
*Each Input option listed may also be configured for
Universal Switching Power Supply
PS1
-
Ribbon Cable to
S1
P2
|
| |||||
|
|
|
| |||
MotherBoard | CR5 | |||||
| U5 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| J3 | ||
|
|
| Connections to J1 & J3 are not covered by CSA | ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| J1 |
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Common | TP1 | ||||
|
|
|
|
|
| ||||||
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| P3 |
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| DISCRETE RELAY OPTION | |||||||
|
|
|
| (See dwg. |
|
|
| ||||
|
|
|
| Note: If installed, this option | |||||||
|
|
|
| blocks access to the fuse and | |||||||
D1 |
|
| must be removed to replace fuse. |
RELAY 1 Indicator
D2
RELAY 2 Indicator
3.1 Input / Output Optional PCB’s
P1, P2 and P3 connectors on the motherboard offer unique positions for I/O options described in this section. A screen appears briefly after power up indicating what options types are connected.
WARNING: For continued protection against fire replace only with same type and rating of fuse. (Part # = Littelfuse 217002)
TB1
1 2
+ -
DC PWR
SUPPLY
INPUT
3 Watts MAX
TB2
1 2
+ -
ALARM
RESET
J2
1 | + | - |
AUDIBLE
ALARM OPTION
TB3
1 2
+-
AUX
POWER
OUTPUT
| K1 |
| K2 | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
TB4
1 2 3 4 5 6
C N/O N/C C N/O N/C
RELAY 1 RELAY 2
DRY CONTACTS
TB5
1 2 3
L1 L2 GND
~
.45A 50/60 Hz
AC POWER
TB1 |
| TB2 |
| J2 |
Available for 24 VDC |
| Dry contact input for use |
| +Terminal = 24 VDC |
primary power input. |
| with optional remote |
| - Terminal is open |
May also be used as |
| Alarm Reset switch. |
| collector 100mA driver |
battery |
| Wires must be shorter |
| for use with optional 100 |
primary power source. |
| than 10 feet & shielded |
| decibel piezo |
TIE TB5 GND to EARTH |
| if longer than 2 feet. |
| annunciator. |
|
|
|
|
|
TB3
24 VDC power output for remote devices such as transmitters, lights, relays etc. 350mA MAX (see Figure 3.0)
TB4
5 amp resistive SPDT (form C) dry contact relay outputs. Use appropriate diode / snubber devices when switching inductive loads.
TB5
Universal
Important: GND terminal 3 must be tied to earth for correct shielding of incoming signals.
SHOCK HAZARD RISK OF ELECTRICAL
Figure 3-2. Motherboard Relays and Terminals
HA40 Technical Manual | Revision 1 (08/08) |