Hearth and Home Technologies PMH, MBK installation instructions Connection to a Masonry Fireplace

Page 14

R

Yosemite Wood Stove

SOLID PACK CHIMNEY WITH METAL SUPPORTS AS A THIMBLE (CONT'D)

First, make the frame for the thimble, ensuring it is no smaller than 14 inches (356mm) square to maintain a 2 inch (51mm) air space around the chimney section.

Attach the wall spacer to the chimney side of the frame. Then insert the frame into the opening, toe nailing it to the wall studs. Install the wall band in the framing to secure the chimney section in place.

CONNECTION TO A MASONRY

FIREPLACE

There are several kits available to connect the stove to a masonry fireplace. Look for a listed kit. The kit is an adapter which is installed at the location of the fireplace damper. The existing damper may have to be removed to allow installation of the kit.

Insert a single section of chimney connector into the chimney through the wall band, being sure it does not protrude into the chimney beyond the edge of the chimney flue lining.

Apply high temperature furnace cement to the end of the chimney section and install it over the connector, through the wall spacer. Tighten the wall band to hold the chimney section firmly in place and against the chimney.

Install the trim collar on the outside of the opening. A 1 inch (25mm) air space between the connector and the chimney section must be maintained.

During installation a 2 inch (51mm) air space to the wood framing is maintained. Do not fill this space with insulation. Insulation in this air space will cause a heat buildup which may ignite the wood framing.

Min. Chimney Clearance

Min. Clearance

to Wall Spacer and

2" (51mm)

Combustibles - 2" (51mm)

 

 

1" (25mm) Air

Chimney Flue

Space to Chimney

Liner

Section

Fireclay

Chimney

Liner or

Equivalent

Connector

 

Chimney Section

 

Trim Collar

 

Wall Band

 

 

Wall Spacer

Masonry Chimney

 

Constructed to NFPA 211

 

Figure 14A

 

 

Fire Clay

 

 

Flue Liner

 

 

with Airspace

 

 

Masonry

Trim Collar

 

Chimney

 

 

Chimney Section

 

Wall Spacer

 

 

with 2" (51mm)

 

Wall Band to

Clearance to

 

 

Secure

Combustibles

 

 

Chimney

 

 

Section

 

Chimney

Wood Studs Used for

 

Connector

 

Framing - Spaced 2"

 

 

(51mm) clearance

 

 

from Masonry

Figure 14B

The key points of this type of stove connection are: 1) that the connector pipe must extend up the chimney above where the fire clay liner starts, and 2) the areas of the kit installation and penetration should fit tightly and be sealed with high temperature furnace cement unless the kit’s instructions state otherwise. (See Figure 14C). The tight fitting installation aids the proper draw of the chimney.

Support Plate & Clamp

 

Listed Rigid

Fireclay liner 5/8"

Stainless Liner

(16mm) Minimum or

 

Equivalent.

Stainless Steel

Carry Stovepipe

Above the Liner

Flex Section

 

Stainless

Damper Plate is

Connector

Removed or

Pipe

Fastened in Open

 

Position

Use Damper Adapter or Seal With Sheetmetal and Sealant

6

Cleanout

Heat Shield

Stainless Tee with Cleanout

Figure 14C

Horizontal Flue Heat Shield, Accessory Part HTSHLD-7006 is required for rear vent installations.

Page 14

7004-187F September 1, 2008

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Important Safety Notes YosemiteYosemite Wood Stove 007Table of Contents Venting System Installation Materials Needed for Your SafetyChimney Systems Side View Side View with Fuel Door Vent SpecificationsFront View TOP View Rear Vent Double Wall-USA 90O Elbow OFF TOP of Stove Through BackwallSide Fuel Door Locked Shut Both Fuel Doors AccessibleFloor Protection USAHorizontal Venting Both Fuel Doors ACCESSIBLE- CornerSide Fuel Door Locked Shut Corner Bolt fully extended Locating Your StoveInstructions to Unlock Side Fuel Door Converting Collar for Rear Vent Installation Reversible Flue CollarChimney Height Requirements Draft Flue SystemsMasonry Chimney Solid Pack Chimney with Metal Supports AS a Thimble Connection to a Masonry Fireplace Solid Pack Chimney with Metal Supports AS a Thimble ContdConnection to a Metal Prefabricated Chimney Interior ChimneyMobile Home Installation Set off smoke alarmsOutside AIR KIT Installation PartOperating Instructions Important Please Read Before Using StoveSymptoms of Over-Firing Fire RiskAIR Controls Primary AIR SystemHeat Output Settings BTU / Hr Start-Up Air Control Primary ControlCorrect Position Correct Baffle & Blanket PlacementIncorrect Positions Wood Selection and Storage OpacityBurn Rates Blower Operating InstructionsCreosote MaintenanceChimney Cleaning ASH RemovalCare and Cleaning Plated Surfaces Door Handle Assemblies Maintenance ContdGlass Replacement Glass Care ContdMaintenance Brick Replacement Instructions Baffle Removal & InstallationYosemite Wood Stove Service & Maintenance Log Front Door Assembly Side Door Assembly Yosemite Wood Stove Exploded ViewsService Parts SKUCast Parts Individual Pieces Warranty Policy CONDITIONS, Exclusions & Limitation of LiabilityHearth & Home Technologies Limited Warranty Contd Yosemite Wood Stove

MBK, PMH specifications

Hearth and Home Technologies (HHT) is a well-known name in the hearth industry, renowned for its commitment to innovation and quality in heating solutions. Their PMH and MBK series represent the pinnacle of modern wood-burning appliance technology, designed to meet varying consumer needs while prioritizing performance, efficiency, and environmental responsibility.

One of the standout features of the PMH (Performance Modular Home) line is its ability to blend seamlessly into a variety of home designs. It offers a sleek and contemporary aesthetic, making it a preferred choice for modern home builders. This series prioritizes efficient wood utilization, ensuring that users have a reliable source of sustainable heat. With high-efficiency ratings, the PMH units burn wood more thoroughly, leading to higher heat output with significantly reduced emissions.

Similarly, the MBK (Modular Built Kit) line excels in versatility and efficiency. Designed for modular homes, the MBK series provides a convenient solution for homeowners seeking efficient heating without compromising on style. These units are engineered to be space-saving, making them ideal for smaller living environments while still delivering impressive heat outputs. Their modular design allows for easy installation and maintenance, differentiating them from traditional wood stoves.

Both series incorporate advanced combustion technologies, which maximize fuel efficiency and reduce emissions. Features such as secondary combustion systems enhance the burning process, leading to cleaner emissions and lowering the environmental impact of wood heating. This is particularly vital in today’s eco-conscious market, where sustainability is a key consideration for consumers.

The HHT PMH and MBK series are equipped with various customization options, allowing homeowners to tailor their heating solutions to their specific requirements. Choices include different finishes, sizes, and control options, enabling users to create a hearth experience that aligns with their tastes and home decor.

In conclusion, Hearth and Home Technologies’ PMH and MBK series stand out for their blend of style, efficiency, and advanced technology. They not only provide reliable heating solutions but do so in a manner that respects the environment and meets the modern consumer’s desire for both functionality and design. For those seeking top-tier wood-burning technology, HHT’s offerings present a compelling choice worth considering.
Top Page Image Contents