Hearth and Home Technologies GBI25 Rock Wool Placement, Brass Trim Cleaning, Valve Access

Page 10

GBI25 SERIES B-VENT GAS FIRED FIREPLACE INSERT

d.Rock Wool Placement

The log set is shipped in place. Tear the rock wool into pieces no larger than 1/2” diameter. Place the rock wool in front of the flange located in the middle of the burner. Do not place the rock wool behind or above the 3/8” flange. This will block the air slot and cause carbon desposits on the log. Place the rock wool on both the left and right sides to complete the burning ember look. It is not necessary to use the entire bag. See Figure 17.

Figure 17 - Rock Wool Placement

Note: Placement of the rock wool should be done with care and time, as this will create the look of the fire when burning.

e.Glass Frame Installation

1)When cleaning the glass, use only non- caustic, non-abrasive cleaners. DO NOT ATTEMPT TO CLEAN HOT GLASS. It is dangerous, and the glass is more likely to be stained by the cleaning agent. Stubborn film can often be removed using Brasso® or a non-abrasive cleaner.

2)After cleaning the glass, position the tabs on the glass frame into the slots on the column of the appliance. Hold door in place and secure with screws removed earlier. Be careful not to over-tighten.

f.Brass Trim Cleaning

All prints and smudges must be wiped clean from the brass trim prior to initial burn. If this is not done, these prints will be cured into the brass finish and set for the life of the appliance. To keep the finish looking its best, gently wipe with a soft cloth after the appliance has had ample time to cool down. If desired, use a non-abrasive cleaner such as soap and water. Never use any solvent, thinner or abrasive cleaner since these will damage the finish.

g.Valve Access

The valve is located behind the control access panel. Lift the panel up and rotate forward. See Figure 18. This will expose the gas valve, variable regulator and fan control, as shown in Figure 19.

Figure 18 - Valve Access

Figure 19 - Gas Valve, Variable Regulator & Fan Control

WARNING!

Never operate this appliance with the glass removed or not sealed.

WARNING!

Do not operate appliance with the panel(s) removed, cracked or broken. Replacement of the panel(s) should be done by a licensed or qualified service person.

26678 Rev H

10

02-02

Image 10
Contents GBi25 Series Vent GAS Fired Fireplace Insert Room HeaterContents Listings and Code Aprovals Description of the SystemSystem Components Dimensions and ClearancesMantel GAS Pressure PRE-INSTALLATION PreparationHigh Altitude Installation ComponentsGAS Line Installation STEP-BY-STEP Installation of the SystemVenting Requirements Label Appliance InstallationFirebox Entry Installation of Appliance Surround InstallationElectrical Grounding Instructions Brass Trim Cleaning Rock Wool PlacementValve Access Log Assembly Removal Firebox Bottom RemovalWiring Wiring DiagramPRE-USE Checklist Optional Wall ThermostatFor Your Safety Read Before Lighting Operating InstructionsSeasonal Shutdown Operation Procedure During Regular USEShutdown During Regular USE FAN OperationMaintenance Instructions Troubleshooting Replacement Parts GBi25 Log AssemblyBattery Operated Remote Control With Thermostat Control Remote Control with Thermostat ControlOptional Components HOMEOWNER’S Notes HOMEOWNER’S Notes HOMEOWNER’S Notes Index How to Obtain Service Limited Lifetime WarrantyYear Limited Warranty Conditions, Exclusions, & Limitations of Liability

GBI25 specifications

Hearth and Home Technologies has garnered a strong reputation for producing high-quality, efficient, and stylish heating solutions for homes, and the GBI25 model exemplifies this commitment. The GBI25 is a gas-burning insert specifically designed to fit seamlessly into existing masonry fireplaces, transforming traditional hearths into modern heating powerhouses while preserving the aesthetic appeal of classic designs.

One of the standout features of the GBI25 is its high-efficiency performance. With an impressive efficiency rating, this insert is constructed to ensure that more heat is generated from less energy, allowing homeowners to enjoy cozy warmth while keeping fuel costs down. The insert’s high BTU output makes it suitable for heating a range of spaces, providing a perfect option for those looking to enhance their living environments.

The GBI25 is equipped with advanced technology that includes an integrated electronic ignition system. This feature simplifies the lighting process, eliminating the need for matches or kindling. Furthermore, the insert is designed with a variable speed blower that can be adjusted according to the homeowner's needs, distributing heat evenly and efficiently throughout the room.

Aesthetically, the GBI25 does not compromise on style. It offers a range of customizable options, including various front designs, finishes, and decorative elements. Homeowners can choose from classic arched or modern linear styles, allowing the insert to blend seamlessly with any décor. The realistic log set and glowing ember bed enhance the visual warmth of the fire, creating a captivating centerpiece in any living space.

Safety remains a top priority with the GBI25. It comes with a built-in safety shut-off system, ensuring peace of mind during operation. Additionally, the insert is equipped with a glass front, which prevents direct contact with the flames, making it safer for homes with children and pets.

Overall, the Hearth and Home Technologies GBI25 gas insert combines efficiency, safety, and style, making it a stunning and practical choice for homeowners looking to elevate their living spaces. Whether for ambiance or heating, the GBI25 provides an exceptional solution for enjoying the comfort of a stylish fire.