Hearth and Home Technologies GBI25 Installation of Appliance, Surround Installation

Page 8

GBI25 SERIES B-VENT GAS FIRED FIREPLACE INSERT

b.Installation of Appliance

1)The appliance should be set on a level surface. Located on the bottom pan of the appliance are two 5/16-18 nuts. Bolts (provided) may be used for leveling purposes.

2)Place appliance on hearth and slide the appliance into the fireplace. Position the draft tube in the hold located on the back. Reach through the exhaust hole and grab the draft hood. See Figure 7. Continue to slide appliance back until draft hood is in position. Reinstall four screws around the exhaust hole.

Figure 7

3)Place the flex line through the gas line access hole on the right side and connect it to the manual shutoff valve. Turn on the gas and check for leaks with a soap and water solution or a gas leak detector. If a leak is detected, tighten the fitting and recheck all joints.

Reinstall the baffle with two screws.

c.Surround Installation

1)Carefully remove the surround parts from the shipping carton. Attach the surround top to each side with two screws provided. See Figure 8. Located on the surrounds is a bend tab used to cover the switch leads. For Model

Figure 8 - Attach Surround Top

GSD24, the bend tab is located on the top of the right surround side. For Models GSD40 and GSD46 the bend tab is located on the right side of the top surround. Use a pair of pliers to bend the tab forward. See Figure 8.

Figure 9 - Installation of Surround Hood

Figure 10 - Installation of Surround Hood

2)For zero clearance fireplaces or fireplaces with combustible material within 12 inches of the firebox opening, it is required to use the surround hood (black). This hood is not required for masonry fireplaces. To install the surround hood, bend the tabs down, as shown in Figure 9. Place the tab through the slots in the surround top and bend the small tab over. See Figure 10.

3)Place three screws in the surround top and slide the brass hood over the screws. Remove the plastic coating on brass before securing. See Figure 11.

4)Assemble the brass trim with brackets provided, as shown in Figure 12. Slide the brass trim on the surround (Figure 13).

5)To install the surround, place hooks on the surround side into slots located on the column (Figure 14).

6)Locate the electrical cord on the left side of the appliance and route it through the surround and trim. Make sure that the electircal cord is routed away from the appliance.

26678 Rev H

8

02-02

Page 7 Page 9
Image 8
Page 7 Page 9
Contents GBi25 Series Vent GAS Fired Fireplace Insert Room HeaterContents Listings and Code Aprovals Description of the SystemMantel Dimensions and ClearancesSystem Components PRE-INSTALLATION Preparation High Altitude InstallationGAS Pressure ComponentsVenting Requirements STEP-BY-STEP Installation of the SystemGAS Line Installation Firebox Entry Appliance InstallationLabel Installation of Appliance Surround InstallationElectrical Grounding Instructions Valve Access Rock Wool PlacementBrass Trim Cleaning Log Assembly Removal Firebox Bottom RemovalWiring Wiring DiagramPRE-USE Checklist Optional Wall ThermostatFor Your Safety Read Before Lighting Operating InstructionsOperation Procedure During Regular USE Shutdown During Regular USESeasonal Shutdown FAN OperationMaintenance Instructions Troubleshooting Replacement Parts GBi25 Log AssemblyOptional Components Remote Control with Thermostat ControlBattery Operated Remote Control With Thermostat Control HOMEOWNER’S Notes HOMEOWNER’S Notes HOMEOWNER’S Notes Index Limited Lifetime Warranty Year Limited WarrantyHow to Obtain Service Conditions, Exclusions, & Limitations of Liability

GBI25 specifications

Hearth and Home Technologies has garnered a strong reputation for producing high-quality, efficient, and stylish heating solutions for homes, and the GBI25 model exemplifies this commitment. The GBI25 is a gas-burning insert specifically designed to fit seamlessly into existing masonry fireplaces, transforming traditional hearths into modern heating powerhouses while preserving the aesthetic appeal of classic designs.

One of the standout features of the GBI25 is its high-efficiency performance. With an impressive efficiency rating, this insert is constructed to ensure that more heat is generated from less energy, allowing homeowners to enjoy cozy warmth while keeping fuel costs down. The insert’s high BTU output makes it suitable for heating a range of spaces, providing a perfect option for those looking to enhance their living environments.

The GBI25 is equipped with advanced technology that includes an integrated electronic ignition system. This feature simplifies the lighting process, eliminating the need for matches or kindling. Furthermore, the insert is designed with a variable speed blower that can be adjusted according to the homeowner's needs, distributing heat evenly and efficiently throughout the room.

Aesthetically, the GBI25 does not compromise on style. It offers a range of customizable options, including various front designs, finishes, and decorative elements. Homeowners can choose from classic arched or modern linear styles, allowing the insert to blend seamlessly with any décor. The realistic log set and glowing ember bed enhance the visual warmth of the fire, creating a captivating centerpiece in any living space.

Safety remains a top priority with the GBI25. It comes with a built-in safety shut-off system, ensuring peace of mind during operation. Additionally, the insert is equipped with a glass front, which prevents direct contact with the flames, making it safer for homes with children and pets.

Overall, the Hearth and Home Technologies GBI25 gas insert combines efficiency, safety, and style, making it a stunning and practical choice for homeowners looking to elevate their living spaces. Whether for ambiance or heating, the GBI25 provides an exceptional solution for enjoying the comfort of a stylish fire.
Top Page Image Contents