Hearth and Home Technologies FL92 MULTI-SIDED owner manual Install Termination Cap

Page 34

D. Install Termination Cap

Install the chimney sections up through the chase enclo- sure.

•Refer to termination cap instructions.

Warning! Risk of Fire! The minimum overlap of cap to pipe (as shown in the following illustrations) MUST be met or chimney may separate from cap. Separation allows sparks, heat and embers to escape.

Notice: Paint the termination cap with a rust-resistant paint to protect against the effects of corrosion on those parts exposed to the weather.

•TR11 Round Termination Cap

•TR11T Round Telescoping Termination Cap

Assemble

Termination

storm collar

Cap

around extended

 

termination cap

 

pipe

 

once cap is

 

installed.

Do NOT

 

Caulk gaps between

block air

holes

storm collar & pipe,

Storm

and storm collar

Collar

& chase top.

3 clip brackets.

 

Slip over chase collar

 

and attach with screws

 

provided.

Collar

 

2 in. (51 mm)

14 1/2 in. (368 mm)

Minimum Height

Maximum

 

Termination

Cap

Slip

storm collar

around chimney pipe

before termination cap pipe is snapped into the chimney pipe.

Caulk gaps between

Storm

storm collar & pipe,

Collar

and storm collar

 

& chase top.

 

Collar

 

2 in. (51 mm)

Chimney

Minimum Height

Pipe

 

Chase Top

 

Do NOT

block air holes

6 in. (153 mm) Minimum top of chase to top of chimney pipe

Chase Top

Chase

Chimney

Pipe

Termination cap pipe and chimney section must overlap 1-1/2 in. (38 mm)

Figure 9.5 Installing a TR11T Round Telescoping Termination Cap

•ST1175 Square Termination Cap

Chase

Termination cap pipe and chimney section must be snapped together to maintain an overlap of 1-1/2 in. (38 mm).

Figure 9.4 Installing a TR11 Round Termination Cap

Flange

Termination Cap

Collar

2 in. (51 mm)

Minimum Height

Chase Top

Chimney

Pipe

Place waterproof caulk or sealer under each flange of the termination cap and on top of each screw to help prevent leaks.

The last section of pipe must stop between 2 in. (51

mm)above the top of the chase and 4 3/4 in. (121

mm) below the top of the chase.

2 in. (51 mm)

maximum

4 3/4 in. (121 mm)

maximum

Chase

Termination cap pipe and chimney section must overlap 1-1/2 in. (38 mm)

Figure 9.6 Installing an ST1175 Square Termination Cap

34

Heatilator • FL92 Multi-Sided Woodburning Fireplace • 34955 • Rev AA 7/12

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Fire Risk Hot screen/mesh and glass doors will cause burnsGrate Listing Label Information/LocationNumber Model Installer Guide Table of ContentsUser Guide Limited Warranty Hearth & Home Technologies Inc Limited Lifetime WarrantyWarranty Conditions This warranty is void ifNon-Combustible Materials Listing and Code ApprovalsAppliance Certification Combustible MaterialsYour Fireplace Operating InstructionsHot glass will cause burns Grate Seasoned WoodStarting a Fire FirescreenOptional Components Glass DoorsVented Gas Log Sets & Gas Log Lighters Clear SpaceWood Fuel Disposal of Ashes Maintenance and ServiceChimney Inspection/Cleaning Creosote Formation and Need for RemovalInspect Grate Glass CleaningCheck Firebox Refractory Frequency As desiredTroubleshooting Guide Start Fire Problems Possible Cause SolutionGetting Started Typical Fireplace SystemDraft Design and Installation ConsiderationsNegative Pressure Locating Fireplace & Chimney Frequently open doors Central heat outlets or returnsFireplace System Requirements Tools and Supplies NeededInspect Fireplace and Components Framing & Clearances Select Fireplace LocationClearances Air Space ClearancesSidewalls/Surrounds Frame the FireplacePosition the Fireplace Installation of FireplaceThings to Consider Place Protective Metal Hearth StripsFt min. from top of uppermost chimney section to air inlet Install Outside Air Kit AK14/AK18 InstallationChimney Assembly Chimney Requirements Height of Chimney ComponentsUsing Offsets/Returns ExampleInstall Chimney Air Kit Assemble Chimney SectionsInstall Ceiling Firestops Installing the Ceiling FirestopInstall Attic Insulation Shield 330 mmFollowing steps should be skipped if using a chase Complete InstallationInstall Flashing Cut out Hole in RoofChimney Termination Requirements Flat RoofsChase Installations Construct the ChaseInstall Fireplace & Chimney Install Chase TopInstall Termination Cap ST1175 Square Termination CapTCT1175 Terra Cotta Cap Field Constructed Shrouds ShroudsRadiation Shield Open Top Shroud TR11/TR11T caps require radiation shieldMailbox Style Shroud radiation shield required Roofed Style Shroud radiation shield requiredHearth Extension Finishing= 1/k x inches of thickness Hearth Extension Dimensions Finishing Material Hearth Refractory In. Micore or equivilent insulationCombustible Mantel SealantWood Burning Inserts AccessoriesGas Log/Lighter Provision Gas Code, Ansi Z223.1Reference Materials Fireplace Dimensions13 mm Chimney Components Catalog # Description15-1/4 387 mm 25-1/4 737 mm 641 mm 483 mm 15-5/8 397 mm Part numbers on following Service PartsMulti-Sided Woodburning Fireplace At Depot StockedContact Information

FL92 MULTI-SIDED specifications

The Hearth and Home Technologies FL92 MULTI-SIDED fireplace stands out as a versatile and stylish option for modern living spaces. This innovative fireplace offers impressive functionality, blending warmth and ambiance with contemporary design. One of its main features is its multi-sided configuration, which allows for a unique installation that can transform any room. With options for both three-sided and two-sided designs, it facilitates an open, spacious feel and encourages a flow of light and warmth across multiple areas.

The FL92 MULTI-SIDED is built with advanced technology that enhances both performance and user experience. It features a powerful heat exchanger system that efficiently distributes warmth throughout the room, making it an excellent choice for heating larger areas. Additionally, its adaptive ignition ensures an efficient burn, minimizing energy consumption while maximizing output. This eco-friendly approach not only benefits homeowners but also the environment by reducing emissions.

The design of the FL92 MULTI-SIDED is equally impressive. It boasts a sleek, contemporary appearance that can seamlessly integrate into various interior styles, from modern to rustic. The expansive glass viewing area provides an unobstructed view of the mesmerizing flames, creating a focal point in any setting. Customizable trim options and finishes allow homeowners to tailor the fireplace to their specific aesthetic preferences, ensuring it complements their decor beautifully.

One of the standout characteristics of the FL92 MULTI-SIDED is its ease of operation. The fireplace can be controlled via a remote, offering convenience for users when managing heat and flame height. Moreover, it includes a self-diagnostic control system that aids in monitoring the fireplace's performance, ensuring safety and efficiency over time.

Whether used as a primary heating source or a visual centerpiece, the Hearth and Home Technologies FL92 MULTI-SIDED fireplace offers an impressive combination of style, functionality, and innovative technology. Its multi-sided design, efficient heating capabilities, eco-friendly operation, and aesthetic versatility make it an exceptional choice for homeowners looking to enhance their living spaces with the warmth and charm of a contemporary fireplace.
Top Page Image Contents