Hearth and Home Technologies FL92 MULTI-SIDED owner manual Finishing Material

Page 40

D. Finishing Material

Refer to Sections 11.A. and Sections 11.B. for combus- tible/non-combustible materials. Refer to Figure 11.2 for non-combustible zone.

Warning! Risk of Fire! You must maintain clearances.

•Use only non-combustible framing material below standoffs.

•Sheetrock, wood or other combustibles must NOT be used as sheathing or facing in the non-combustible zone.

•Do NOT cover metal fireplace front with combustible materials.

•Install combustible materials only to specified clearances on top front and side edges.

•Complete framing and apply facing material (drywall) over framing.

•A bead of 300-deg F minimum non-combustible sealant must be used to close off any gaps at the top and sides between the fireplace and facing to prevent cold air leaks.

•Large gaps can be bridged with fiberglass rope gasket.

•Only non-combustible materials may be used to cover the metal fireplace front.

The metal surfaces of the fireplace may be covered with non-combustible materials only.

Do not cover grills.

Figure 11.2 Non-combustible Materials Zone

Finished combustible wall

 

 

 

 

 

Flat 2 x 4 stud wall

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Combustible material

 

 

 

2 x 4 header, flush with

 

 

 

front of stand-offs

 

 

 

 

 

 

 

 

Non-combustible decorative facing (up to full brick depth)

Continuous, non-combustible sealant

Tile, stone or other non-combustible material

Hearth Refractory

1/2 in. Micore or equivilent insulation

Figure 11.3 Decorative Facing

Metal strips are placed 2 in. (51 mm) under the front of the fireplace and must extend beyond the front and sides of fireplace opening by 2 in. (51 mm)

Floor constructed of wood or other combustible material

40

Heatilator • FL92 Multi-Sided Woodburning Fireplace • 34955 • Rev AA 7/12

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Fire Risk Hot screen/mesh and glass doors will cause burnsGrate Listing Label Information/LocationNumber Model Installer Guide Table of ContentsUser Guide Limited Warranty Hearth & Home Technologies Inc Limited Lifetime WarrantyWarranty Conditions This warranty is void ifListing and Code Approvals Appliance CertificationNon-Combustible Materials Combustible MaterialsYour Fireplace Operating InstructionsHot glass will cause burns Seasoned Wood Starting a FireGrate FirescreenGlass Doors Vented Gas Log Sets & Gas Log LightersOptional Components Clear SpaceWood Fuel Maintenance and Service Chimney Inspection/CleaningDisposal of Ashes Creosote Formation and Need for RemovalGlass Cleaning Check Firebox RefractoryInspect Grate Frequency As desiredTroubleshooting Guide Start Fire Problems Possible Cause SolutionGetting Started Typical Fireplace SystemDraft Design and Installation ConsiderationsNegative Pressure Locating Fireplace & Chimney Frequently open doors Central heat outlets or returnsFireplace System Requirements Tools and Supplies NeededInspect Fireplace and Components Framing & Clearances Select Fireplace LocationClearances Air Space ClearancesSidewalls/Surrounds Frame the FireplaceInstallation of Fireplace Things to ConsiderPosition the Fireplace Place Protective Metal Hearth StripsFt min. from top of uppermost chimney section to air inlet Install Outside Air Kit AK14/AK18 InstallationChimney Assembly Chimney Requirements Height of Chimney ComponentsUsing Offsets/Returns ExampleInstall Chimney Air Kit Assemble Chimney SectionsInstall Ceiling Firestops Installing the Ceiling FirestopInstall Attic Insulation Shield 330 mmComplete Installation Install FlashingFollowing steps should be skipped if using a chase Cut out Hole in RoofChimney Termination Requirements Flat RoofsChase Installations Construct the ChaseInstall Fireplace & Chimney Install Chase TopInstall Termination Cap ST1175 Square Termination CapTCT1175 Terra Cotta Cap Shrouds Radiation ShieldField Constructed Shrouds Open Top Shroud TR11/TR11T caps require radiation shieldMailbox Style Shroud radiation shield required Roofed Style Shroud radiation shield requiredHearth Extension Finishing= 1/k x inches of thickness Hearth Extension Dimensions Finishing Material Hearth Refractory In. Micore or equivilent insulationCombustible Mantel SealantAccessories Gas Log/Lighter ProvisionWood Burning Inserts Gas Code, Ansi Z223.1Reference Materials Fireplace Dimensions13 mm Chimney Components Catalog # Description15-1/4 387 mm 25-1/4 737 mm 641 mm 483 mm 15-5/8 397 mm Part numbers on following Service PartsMulti-Sided Woodburning Fireplace At Depot StockedContact Information

FL92 MULTI-SIDED specifications

The Hearth and Home Technologies FL92 MULTI-SIDED fireplace stands out as a versatile and stylish option for modern living spaces. This innovative fireplace offers impressive functionality, blending warmth and ambiance with contemporary design. One of its main features is its multi-sided configuration, which allows for a unique installation that can transform any room. With options for both three-sided and two-sided designs, it facilitates an open, spacious feel and encourages a flow of light and warmth across multiple areas.

The FL92 MULTI-SIDED is built with advanced technology that enhances both performance and user experience. It features a powerful heat exchanger system that efficiently distributes warmth throughout the room, making it an excellent choice for heating larger areas. Additionally, its adaptive ignition ensures an efficient burn, minimizing energy consumption while maximizing output. This eco-friendly approach not only benefits homeowners but also the environment by reducing emissions.

The design of the FL92 MULTI-SIDED is equally impressive. It boasts a sleek, contemporary appearance that can seamlessly integrate into various interior styles, from modern to rustic. The expansive glass viewing area provides an unobstructed view of the mesmerizing flames, creating a focal point in any setting. Customizable trim options and finishes allow homeowners to tailor the fireplace to their specific aesthetic preferences, ensuring it complements their decor beautifully.

One of the standout characteristics of the FL92 MULTI-SIDED is its ease of operation. The fireplace can be controlled via a remote, offering convenience for users when managing heat and flame height. Moreover, it includes a self-diagnostic control system that aids in monitoring the fireplace's performance, ensuring safety and efficiency over time.

Whether used as a primary heating source or a visual centerpiece, the Hearth and Home Technologies FL92 MULTI-SIDED fireplace offers an impressive combination of style, functionality, and innovative technology. Its multi-sided design, efficient heating capabilities, eco-friendly operation, and aesthetic versatility make it an exceptional choice for homeowners looking to enhance their living spaces with the warmth and charm of a contemporary fireplace.
Top Page Image Contents