Hearth and Home Technologies EM-415 - 36 owner manual Cut out Hole in Roof, Complete Installation

Page 30

G. Cut out Hole in Roof

•Refer to Figure 8.9.

•Plumb from roof to center of chimney.

•Drive a nail up through roof to mark center of pipe.

•Measure to either side of nail and mark the 14-1/2 in. x 14-1/2 in. (368 mm x 368 mm) opening required.

•Measure opening on the horizontal; actual length may be larger depending on roof pitch.

•Cut out and frame opening.

•Refer to Chapter 25 of the Uniform Building Code for roof framing details.

H. Complete Installation

WARNING! Risk of Fire! You MUST maintain 2 in.

(51 mm) air space to insulation and other combustible materials around the chimney system. Failure to do so could cause overheating and fire.

•Keep chimney sections from separating or twisting.

•You may secure straight chimney sections at the joints with screws no longer than 1/2 in. (13 mm).

The following steps should be skipped if using a chase.

•Install roof flashing appropriate to roof pitch.

•Install round termination cap and storm collar following instructions shipped with the cap.

I. Install Flashing

•Assemble chimney so it passes through the framed opening.

•Slip the flashing over the chimney.

NOTICE: Roofing shingles must be below the flashing plate on the lower side of a sloped roof and over the flashing plate on the sides and top.

•Nail the flashing to the roof. Keep gaps between the flashing plate and the roof to a minimum.

•Caulk the flashing plate and roof junction as well as the vertical seam on the flashing. All nail heads must be caulked with a roofing sealant.

Figure 8.9 Ceiling/Attic Construction

30

Heat & Glo • EM-415, EM-485 • 33056 • Rev W • 10/08

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Hot screen/mesh and glass doors will cause burns Wood Burning FireplaceOperation Fire RiskListing Label Information/Location GrateNumber Safety Alert Key Table of ContentsInstaller Guide User Guide¨ Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of LiabilityHeat & Glo EM-415, EM-485 33056 Rev W 10/08 Non-Combustible Materials Listing and Code ApprovalsAppliance Certification Combustible MaterialsOperating Instructions Your FireplaceHot glass will cause burns Grate Seasoned WoodStarting a Fire FirescreenOptional Components Glass DoorsVented Gas Log Sets & Gas Log Lighters Clear SpaceWood Fuel Hardwood vs SoftwoodMaintainance and Service Chimney Inspection/CleaningDisposal of Ashes Inspect Grate Glass CleaningCheck Firebox Refractory Frequency As desiredTroubleshooting Guide Start Fire Problems Possible Cause SolutionGetting Started Typical Fireplace SystemDesign and Installation Considerations DraftNegative Pressure Locating Fireplace & Chimney Frequently open doors Central heat outlets or returnsTools and Supplies Needed Inspect Fireplace and ComponentsFraming & Clearances Fireplace Dimensions .A 1219 mm MinimumMm all configurations Select Fireplace LocationClearances Clearances to Combustible MaterialsSidewalls/Surrounds Frame the FireplacePosition the Fireplace Installation of FireplaceThings to Consider Place Protective Metal Hearth StripsFt min. from top of uppermost chimney section to air inlet Hood Wire Ties Install Outside Air KitJunction Box Installation Secure flex duct with metal tape, screws or wire tiesInstallation of Fan Prepare Junction Box BracketChimney Assembly Maintain minimum height of chimney above roofChimney Requirements Height of Chimney ComponentsUsing Offsets/Returns ExampleInstall Chimney Air Kit Installing Ceiling FirestopsAssembling Chimney Sections Installing Attic Insulation Shield Prepare Attic Insulation ShieldComplete Installation Install FlashingCut out Hole in Roof Chimney Termination Requirements Flat RoofsGas line holes and other openings should be caulked with Chase InstallationsConstruct the Chase Chase should be constructed in the manner of allInstall Fireplace & Chimney Install Chase TopInstall Termination Cap ST375 Square Termination CapTS345/TS345P Square Termination Cap European Copper Series Termination CapTCT375 Terra Cotta Cap Radiation Shield Some shrouds require a radiation shield. Use where specifiedShrouds Field Constructed ShroudsMailbox Style Shroud radiation shield required Finishing Hearth Extension= 1/k x inches of thickness Finishing Material Noncombustible FacingCombustible Mantel 305 mmGas Log/Lighter Provision AccessoriesInstall Fan Wood Burning InsertsOutside 23-3/8 92 mmGas Knockout Air 594 mmFireplace Components Catalog # Description1676 mm 508 mm 13 mmChimney Components Catalog #305 mm 27-3/8 24-5/8 695 mm 625 mm Effective Outside Height Diameter 10-1/2 121 mm 267 mm10-1/2 267 mm 305 mm 24-5/8 625 mm 787 mmTR-TVK CT-3A 10-7/8 276 mm Service Parts EM-415EM-485T This page intentionally left blank Do not Discard this Manual

EM-485T - 42, EM-415 - 36 specifications

Hearth and Home Technologies has long been a leader in the fireplace and heating solutions industry, and among their latest offerings is the EM-415 - 36 and EM-485T - 42 models. These elegant units blend aesthetics with advanced technology, making them a perfect addition to any modern home.

The EM-415 - 36 model features a 36-inch viewing area, offering an expansive flame look that enhances any room's ambiance. On the other hand, the EM-485T - 42 boasts a larger 42-inch viewing area, providing an even more impressive visual display. Both designs prioritize an open front that allows for maximum natural light while showcasing the fire's beauty.

One of the main features of both models is their efficiency. They utilize advanced venting systems that allow for a balanced flow of air and smoke, ensuring that the fire burns cleanly and efficiently. This not only contributes to a reduced environmental impact but also helps to lower energy costs for homeowners. The EM-415 and EM-485T are designed to meet or exceed various efficiency standards, making them a responsible choice for homeowners concerned about energy use.

In terms of heat output, both models are equipped with powerful burners that provide ample warmth for larger spaces. With adjustable flame settings, users can customize their experience to either enjoy a cozy fire during colder months or opt for a gentle warmth that’s suitable for entertaining during milder weather.

The aesthetic design of the EM-415 and EM-485T is another notable feature. They come with various customizable options, including different finishes and decorative media, allowing homeowners to tailor the appearance to their personal style and home decor. The clean, contemporary aesthetic ensures that these fireplaces are not just functional, but also a centerpiece of elegance in any room.

Installation is made convenient thanks to the thoughtfully designed systems in both models. They can be installed easily in a variety of settings, including new constructions and renovations. The straightforward operation and maintenance further ensure that homeowners will enjoy these fireplaces hassle-free.

Safety is also paramount with Hearth and Home Technologies. The EM-415 and EM-485T units are fitted with advanced safety mechanisms, such as automatic shut-off features and protective screens, ensuring peace of mind for users and their families.

In conclusion, the Hearth and Home Technologies EM-415 - 36 and EM-485T - 42 models combine striking aesthetics with advanced technology and efficiency. Their innovative features and safety measures make them appealing options for those looking to elevate their living space while enjoying the warmth and ambiance of a beautiful fire.
Top Page Image Contents