Hearth and Home Technologies BIR42-B owner manual Maintenance and Service, Disposal of Ashes

Page 11

3Maintenance and Service

A. Disposal of Ashes

Frequency: When they reach bottom of grate

By: Homeowner

Warning! Risk of Fire! Ashes could contain hot embers.

Place ashes in a metal container with a tight-fitting lid.

The closed container should be placed on a non- combustible floor or on the ground, well away from all combustible materials, pending final disposal.

If the ashes are disposed of by burial in soil or otherwise locally dispersed, they should be retained in the closed container until all cinders have thoroughly cooled.

B. Chimney Inspection/Cleaning

Frequency: At least twice a year during heating season or as recommended by a certified chimney sweep

By: Certified chimney sweep

Warning! Risk of Fire! Ignited creosote is extremely HOT. Prevent creosote buildup.

Refer to Figure 3.1 to remove/reinstall termination caps.

Creosote - Formation and Need for Removal

When wood is burned slowly, it produces tar and other organic vapors, which combine with expelled moisture to form creosote. The creosote vapors condense in the rela- tively cool chimney flue of a slow-burning fire. As a result, creosote residue accumulates on the flue lining. When ignited this creosote makes an extremely hot fire.

Warning! Risk of Fire! A chimney fire can permanently damage your chimney system and nearby structures.

In the event of a chimney fire, Hearth & Home Technolo- gies Inc. recommends

replacement of the chimney, and

inspection of the adjacent structure to the provisions of NFPA Level III inspection criteria

The chimney shall be inspected at least twice a year during the heating season to determine when a creosote buildup has occurred.

When creosote has accumulated it shall be removed to reduce the risk of a chimney fire.

Remove 4 screws

Remove screws,and lift top pan off. lift top cover.

Top Cover

 

Cap

Cap

Chimney

 

 

Slip

 

Section

TR11/TR11T

ST1175

TR444/TR442

ST475

Round Termination Cap

Square Termination Cap

Figure 3.1 Chimney & Termination Cap Cleaning

 

1. REMOVE (8) SCREWS

 

 

2. LIFT TOP

 

Remove 2 screws from

 

 

the front and back and

 

TOP

lift the top off.

TOP

 

 

 

SCREW

SCREW

 

 

TCT1175

Terra Cotta

Termination Cap

Available US only

DT SERIES

Heatilator • Birmingham BIR42-B4059-681• 11/11

11

Image 11
Contents Fire Risk Hot screen/mesh and glass doors will cause burnsNumber Listing Label Information/LocationGrate Table of Contents Limited Lifetime Warranty  WarrantyWarranty Conditions Combustible Materials Listing and Code ApprovalsAppliance Certification Non-combustible MaterialsYour Fireplace Operating InstructionsFirescreen Seasoned WoodStarting a Fire GrateClear Space Glass DoorsVented Gas Log Sets & Gas Log Lighters Optional ComponentsHardwood vs Softwood Wood FuelDisposal of Ashes Maintenance and ServiceChimney Inspection/Cleaning Frequency As desired Glass CleaningCheck Firebox Molded Brick Panel Inspect GrateStart Fire Problems Possible Cause Solution Troubleshooting GuideTypical Fireplace System Getting StartedNegative Pressure Design and Installation ConsiderationsDraft Windward Locating your Fireplace & ChimneyTypical Fireplace Components Tools and Supplies Needed Inspect Fireplace and ComponentsModel # Framing & ClearancesSelect Fireplace Location Air Space Clearances ClearancesFrame the Fireplace Sidewalls/SurroundsPlace Protective Metal Hearth Strips Installation of FireplaceThings to Consider Position the FireplaceYES Outside Air Installation Install Outside Air KitChimney Assembly Height of Chimney Components Chimney RequirementsExample Using Offsets/ReturnsAssembling Chimney Sections Assemble Chimney SectionsInstalling the Ceiling Firestop Install Ceiling FirestopsPrepare Attic Insulation Shield Install Attic Insulation ShieldCut Out Hole in Roof Complete InstallationInstall Flashing Flat Roofs Chimney Termination RequirementsConstruct the Chase Chase InstallationsInstall Chase Top Install Fireplace & ChimneyST1175 Square Termination Cap Install Termination CapTCT1175 Terra Cotta Cap Field Constructed Shrouds ShroudsRadiation Shield Mailbox Style Shroud radiation shield required Install Side Molded Brick Panel/Traditional Installation of Molded Brick PanelInstall Hearth Molded Brick Panel Install Back Molded Brick Panel/TraditionalInstall Side Molded Brick Panel Herring- bone Install Back Molded Brick Panel Herring- boneInstall Mortar Optional Install Screens= 1/k x inches of thickness FinishingHearth Extension Finishing Materials Non-combustibleFraming Material Equivalent insulationNon-combustible Sealant Use only non-combustible framing material below standoffs Finishing MaterialStandoffs Combustible MantelAngle Gas Code, Ansi Z223.1 AccessoriesGas Log/Lighter Provision Wood Burning InsertsReference Materials Fireplace DimensionsID6 Insulated Duct Catalog # Chimney Components15-1/4 387 mm 31-3/4 806 mm 34-5/8 879 mm Heatilator Birmingham BIR42-B 4059-681 11/11 Herringbone Refractory Service PartsContact Information

BIR42-B specifications

Hearth and Home Technologies has consistently set the standard for modern heating solutions, and the BIR42-B gas fireplace is no exception. This model stands out for its blend of elegance, efficiency, and technology, making it a highly sought-after choice for homeowners looking to elevate their living spaces.

The BIR42-B features a sleek, contemporary design that seamlessly fits into various decor styles. Measuring 42 inches in width, it provides a generous viewing area to enjoy the mesmerizing flames while adding a focal point to the room. The fireplace comes with a choice of high-quality finishes, allowing homeowners to customize it to their aesthetic preferences.

One of the main features of the BIR42-B is its advanced heating capabilities. With an impressive BTU output, it efficiently warms spaces, making it perfect for both small and large rooms. This model is equipped with a design that maximizes heat circulation, ensuring that warmth is evenly distributed throughout the space.

The BIR42-B also incorporates innovative technologies that enhance user experience. The fireplace comes with a user-friendly remote control, allowing homeowners to adjust flame height and heat settings from the comfort of their seat. This is particularly useful for those chilly evenings when a quick adjustment can make all the difference.

Safety is a primary concern when it comes to heating appliances, and Hearth and Home Technologies has gone the extra mile with the BIR42-B. The unit includes safety features such as an automatic shut-off system and thermal sensors, ensuring peace of mind for users and their families.

Another impressive characteristic is the fireplace's clean-burning technology, which not only adheres to environmental standards but also promotes better air quality inside the home. The BIR42-B is designed to minimize emissions, making it an eco-conscious choice for homeowners.

In summary, the BIR42-B by Hearth and Home Technologies is a top-tier gas fireplace that expertly combines style, functionality, and safety. With its modern design, advanced heating capabilities, user-friendly features, and commitment to environmental responsibility, it stands as an excellent investment for those looking to enhance their home’s ambiance and comfort. This model not only promises warmth but also becomes a central element of design and leisure in any living space.