Hearth and Home Technologies BIR42-B owner manual Finishing Material

Page 44

D. Finishing Material

Refer to Sections 12.A. and Sections 12.B. for combustible/ non-combustible materials. Refer to Figure 12.10 for non- combustible zone.

Warning! Risk of Fire! You must maintain clearances.

•Use only non-combustible framing material below standoffs.

•Sheetrock, wood or other combustibles must NOT be used as sheathing or facing in the non-combustible zone.

•Do NOT cover metal fireplace front with combustible materials.

•Install combustible materials only to specified clearances on top front and side edges.

•Complete framing and apply facing material (drywall) over framing.

•A bead of 300-deg F minimum non-combustible sealant must be used to close off any gaps at the top and sides between the fireplace and facing to prevent cold air leaks.

•Large gaps can be bridged with fiberglass rope gasket.

•Only non-combustible materials may be used to cover the metal fireplace front.

These surfaces

 

must be covered

 

with non-combustible

 

material.

Non-combustible

 

sealant.

Figure 12.9 Non-combustible Facing

 

Note: We recommend mortar be applied after facing materials are installed. Refer to Sec- tion 11.G.

 

2 x 4 stud wall

Finished combustible wall

2 x 4 header, flush with

front of stand-offs

 

Non-Combustible material

 

Non-combustible

 

 

decorative facing

 

 

(up to full brick depth)

 

 

Continuous,

 

 

non-combustible sealant

 

Bottom of fireplace opening

 

 

Tile, stone or other

Hearth

and finished hearth may be

the same height

non-combustible material

Refractory

 

1 in. Micore

 

 

or equivilent

 

 

insulation &

Metal strips are placed 2 in. (51 mm)

 

1/2 in. Durock

Floor constructed of wood or

under the front of the fireplace and must

 

other combustible material

 

extend beyond the front and sides of

fireplace opening by 2 in. (51 mm)

Figure 12.10 Decorative Facing

44

Heatilator • Birmingham BIR42-B • 4059-681 • 11/11

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Hot screen/mesh and glass doors will cause burns Fire RiskNumber Listing Label Information/LocationGrate Table of Contents  Warranty Limited Lifetime WarrantyWarranty Conditions Listing and Code Approvals Appliance CertificationNon-combustible Materials Combustible MaterialsOperating Instructions Your FireplaceSeasoned Wood Starting a FireGrate FirescreenGlass Doors Vented Gas Log Sets & Gas Log LightersOptional Components Clear SpaceWood Fuel Hardwood vs SoftwoodDisposal of Ashes Maintenance and ServiceChimney Inspection/Cleaning Glass Cleaning Check Firebox Molded Brick PanelInspect Grate Frequency As desiredTroubleshooting Guide Start Fire Problems Possible Cause SolutionGetting Started Typical Fireplace SystemNegative Pressure Design and Installation ConsiderationsDraft Locating your Fireplace & Chimney WindwardTools and Supplies Needed Inspect Fireplace and Components Typical Fireplace ComponentsModel # Framing & ClearancesSelect Fireplace Location Clearances Air Space ClearancesSidewalls/Surrounds Frame the FireplaceInstallation of Fireplace Things to ConsiderPosition the Fireplace Place Protective Metal Hearth StripsYES Install Outside Air Kit Outside Air InstallationChimney Assembly Chimney Requirements Height of Chimney ComponentsUsing Offsets/Returns ExampleAssemble Chimney Sections Assembling Chimney SectionsInstall Ceiling Firestops Installing the Ceiling FirestopInstall Attic Insulation Shield Prepare Attic Insulation ShieldCut Out Hole in Roof Complete InstallationInstall Flashing Chimney Termination Requirements Flat RoofsChase Installations Construct the ChaseInstall Fireplace & Chimney Install Chase TopInstall Termination Cap ST1175 Square Termination CapTCT1175 Terra Cotta Cap Field Constructed Shrouds ShroudsRadiation Shield Mailbox Style Shroud radiation shield required Installation of Molded Brick Panel Install Hearth Molded Brick PanelInstall Back Molded Brick Panel/Traditional Install Side Molded Brick Panel/TraditionalInstall Back Molded Brick Panel Herring- bone Install Side Molded Brick Panel Herring- boneInstall Screens Install Mortar Optional= 1/k x inches of thickness FinishingHearth Extension Non-combustible Framing MaterialEquivalent insulation Finishing MaterialsNon-combustible Sealant Finishing Material Use only non-combustible framing material below standoffsCombustible Mantel StandoffsAngle Accessories Gas Log/Lighter ProvisionWood Burning Inserts Gas Code, Ansi Z223.1Fireplace Dimensions Reference MaterialsID6 Insulated Duct Chimney Components Catalog #15-1/4 387 mm 31-3/4 806 mm 34-5/8 879 mm Heatilator Birmingham BIR42-B 4059-681 11/11 Service Parts Herringbone RefractoryContact Information

BIR42-B specifications

Hearth and Home Technologies has consistently set the standard for modern heating solutions, and the BIR42-B gas fireplace is no exception. This model stands out for its blend of elegance, efficiency, and technology, making it a highly sought-after choice for homeowners looking to elevate their living spaces.

The BIR42-B features a sleek, contemporary design that seamlessly fits into various decor styles. Measuring 42 inches in width, it provides a generous viewing area to enjoy the mesmerizing flames while adding a focal point to the room. The fireplace comes with a choice of high-quality finishes, allowing homeowners to customize it to their aesthetic preferences.

One of the main features of the BIR42-B is its advanced heating capabilities. With an impressive BTU output, it efficiently warms spaces, making it perfect for both small and large rooms. This model is equipped with a design that maximizes heat circulation, ensuring that warmth is evenly distributed throughout the space.

The BIR42-B also incorporates innovative technologies that enhance user experience. The fireplace comes with a user-friendly remote control, allowing homeowners to adjust flame height and heat settings from the comfort of their seat. This is particularly useful for those chilly evenings when a quick adjustment can make all the difference.

Safety is a primary concern when it comes to heating appliances, and Hearth and Home Technologies has gone the extra mile with the BIR42-B. The unit includes safety features such as an automatic shut-off system and thermal sensors, ensuring peace of mind for users and their families.

Another impressive characteristic is the fireplace's clean-burning technology, which not only adheres to environmental standards but also promotes better air quality inside the home. The BIR42-B is designed to minimize emissions, making it an eco-conscious choice for homeowners.

In summary, the BIR42-B by Hearth and Home Technologies is a top-tier gas fireplace that expertly combines style, functionality, and safety. With its modern design, advanced heating capabilities, user-friendly features, and commitment to environmental responsibility, it stands as an excellent investment for those looking to enhance their home’s ambiance and comfort. This model not only promises warmth but also becomes a central element of design and leisure in any living space.
Top Page Image Contents