Hearth and Home Technologies BIR42-B owner manual TCT1175 Terra Cotta Cap

Page 35

TCT1175 Terra Cotta Cap

 

Place waterproof sealer

Remove 2 screws

under each flange of the

termination cap and on

from front & back

top of each screw to

to lift the top off

help prevent leaks.

 

Termination Cap

The last section of pipe

 

must stop between 2 in.

 

(51 mm) above top of

Collar

chase and 7 in. (178 mm)

below top of chase

2 in. (51 mm)

 

Minimum Height

 

Chase Top

2 in. (51 mm)

 

7 in. (178 mm)

Chase

Chimney

Pipe

Termination cap pipe and chimney section must overlap

1-1/2 in. (38 mm)

Figure 9.7 Installing a TCT1175 Terra Cotta Cap

Heatilator • Birmingham BIR42-B4059-681• 11/11

35

Image 35
Contents Fire Risk Hot screen/mesh and glass doors will cause burnsNumber Listing Label Information/LocationGrate Table of Contents Limited Lifetime Warranty  WarrantyWarranty Conditions Combustible Materials Listing and Code ApprovalsAppliance Certification Non-combustible MaterialsYour Fireplace Operating InstructionsFirescreen Seasoned WoodStarting a Fire GrateClear Space Glass DoorsVented Gas Log Sets & Gas Log Lighters Optional ComponentsHardwood vs Softwood Wood FuelDisposal of Ashes Maintenance and ServiceChimney Inspection/Cleaning Frequency As desired Glass CleaningCheck Firebox Molded Brick Panel Inspect GrateStart Fire Problems Possible Cause Solution Troubleshooting GuideTypical Fireplace System Getting StartedNegative Pressure Design and Installation ConsiderationsDraft Windward Locating your Fireplace & ChimneyTypical Fireplace Components Tools and Supplies Needed Inspect Fireplace and ComponentsModel # Framing & ClearancesSelect Fireplace Location Air Space Clearances ClearancesFrame the Fireplace Sidewalls/SurroundsPlace Protective Metal Hearth Strips Installation of FireplaceThings to Consider Position the FireplaceYES Outside Air Installation Install Outside Air KitChimney Assembly Height of Chimney Components Chimney RequirementsExample Using Offsets/ReturnsAssembling Chimney Sections Assemble Chimney SectionsInstalling the Ceiling Firestop Install Ceiling FirestopsPrepare Attic Insulation Shield Install Attic Insulation ShieldCut Out Hole in Roof Complete InstallationInstall Flashing Flat Roofs Chimney Termination RequirementsConstruct the Chase Chase InstallationsInstall Chase Top Install Fireplace & ChimneyST1175 Square Termination Cap Install Termination CapTCT1175 Terra Cotta Cap Field Constructed Shrouds ShroudsRadiation Shield Mailbox Style Shroud radiation shield required Install Side Molded Brick Panel/Traditional Installation of Molded Brick PanelInstall Hearth Molded Brick Panel Install Back Molded Brick Panel/TraditionalInstall Side Molded Brick Panel Herring- bone Install Back Molded Brick Panel Herring- boneInstall Mortar Optional Install Screens= 1/k x inches of thickness FinishingHearth Extension Finishing Materials Non-combustibleFraming Material Equivalent insulationNon-combustible Sealant Use only non-combustible framing material below standoffs Finishing MaterialStandoffs Combustible MantelAngle Gas Code, Ansi Z223.1 AccessoriesGas Log/Lighter Provision Wood Burning InsertsReference Materials Fireplace DimensionsID6 Insulated Duct Catalog # Chimney Components15-1/4 387 mm 31-3/4 806 mm 34-5/8 879 mm Heatilator Birmingham BIR42-B 4059-681 11/11 Herringbone Refractory Service PartsContact Information

BIR42-B specifications

Hearth and Home Technologies has consistently set the standard for modern heating solutions, and the BIR42-B gas fireplace is no exception. This model stands out for its blend of elegance, efficiency, and technology, making it a highly sought-after choice for homeowners looking to elevate their living spaces.

The BIR42-B features a sleek, contemporary design that seamlessly fits into various decor styles. Measuring 42 inches in width, it provides a generous viewing area to enjoy the mesmerizing flames while adding a focal point to the room. The fireplace comes with a choice of high-quality finishes, allowing homeowners to customize it to their aesthetic preferences.

One of the main features of the BIR42-B is its advanced heating capabilities. With an impressive BTU output, it efficiently warms spaces, making it perfect for both small and large rooms. This model is equipped with a design that maximizes heat circulation, ensuring that warmth is evenly distributed throughout the space.

The BIR42-B also incorporates innovative technologies that enhance user experience. The fireplace comes with a user-friendly remote control, allowing homeowners to adjust flame height and heat settings from the comfort of their seat. This is particularly useful for those chilly evenings when a quick adjustment can make all the difference.

Safety is a primary concern when it comes to heating appliances, and Hearth and Home Technologies has gone the extra mile with the BIR42-B. The unit includes safety features such as an automatic shut-off system and thermal sensors, ensuring peace of mind for users and their families.

Another impressive characteristic is the fireplace's clean-burning technology, which not only adheres to environmental standards but also promotes better air quality inside the home. The BIR42-B is designed to minimize emissions, making it an eco-conscious choice for homeowners.

In summary, the BIR42-B by Hearth and Home Technologies is a top-tier gas fireplace that expertly combines style, functionality, and safety. With its modern design, advanced heating capabilities, user-friendly features, and commitment to environmental responsibility, it stands as an excellent investment for those looking to enhance their home’s ambiance and comfort. This model not only promises warmth but also becomes a central element of design and leisure in any living space.