Hearth and Home Technologies BIR42-B owner manual 15-1/4 387 mm

Page 51

			Inside
			Diameter
			11 in.
			(279 mm)
	21 in.		Outside
	(533 mm)		Outside
	(533 mm)		Diameter
			Diameter
			13 in.
			(330 mm)
		SL1130 Offset/Return

Assembled

Diameter: 17 in./432 mm

Height: 24 in./610 mm

AS10 Straight Attic Insulation Shield

13 in.	2 in.
(330 mm)

(51 mm)

JB577 Chimney Joint Band

13 in. (330 mm)

CB576 Chimney Joint Band

A

B17 in. (432 mm)

Catalog #	A		B
FS538	0-deg.	17 in.		432 mm
FS540	30-deg.	26 in.		660 mm

15-1/4 in.

(387 mm)

29 in.	25-1/4 in.
(737 mm)	(641 mm)

RF570 Roof Flashing

15-1/4in.

(387 mm)

	39-7/8 in.	28 in.
	39-7/8 in.	(711 mm)
	(1013 mm)	(711 mm)
	(1013 mm)
	RF571 Roof Flashing

Heatilator • Birmingham BIR42-B • 4059-681• 11/11

51

Image 51

Contents

Fire Risk Hot screen/mesh and glass doors will cause burnsListing Label Information/Location GrateNumber Table of Contents Limited Lifetime Warranty  WarrantyWarranty Conditions Combustible Materials Listing and Code ApprovalsAppliance Certification Non-combustible MaterialsYour Fireplace Operating InstructionsFirescreen Seasoned WoodStarting a Fire GrateClear Space Glass DoorsVented Gas Log Sets & Gas Log Lighters Optional ComponentsHardwood vs Softwood Wood FuelMaintenance and Service Chimney Inspection/CleaningDisposal of Ashes Frequency As desired Glass CleaningCheck Firebox Molded Brick Panel Inspect GrateStart Fire Problems Possible Cause Solution Troubleshooting GuideTypical Fireplace System Getting StartedDesign and Installation Considerations DraftNegative Pressure Windward Locating your Fireplace & ChimneyTypical Fireplace Components Tools and Supplies Needed Inspect Fireplace and ComponentsFraming & Clearances Select Fireplace LocationModel # Air Space Clearances ClearancesFrame the Fireplace Sidewalls/SurroundsPlace Protective Metal Hearth Strips Installation of FireplaceThings to Consider Position the FireplaceYES Outside Air Installation Install Outside Air KitChimney Assembly Height of Chimney Components Chimney RequirementsExample Using Offsets/ReturnsAssembling Chimney Sections Assemble Chimney SectionsInstalling the Ceiling Firestop Install Ceiling FirestopsPrepare Attic Insulation Shield Install Attic Insulation ShieldComplete Installation Install FlashingCut Out Hole in Roof Flat Roofs Chimney Termination RequirementsConstruct the Chase Chase InstallationsInstall Chase Top Install Fireplace & ChimneyST1175 Square Termination Cap Install Termination CapTCT1175 Terra Cotta Cap Shrouds Radiation ShieldField Constructed Shrouds Mailbox Style Shroud radiation shield required Install Side Molded Brick Panel/Traditional Installation of Molded Brick PanelInstall Hearth Molded Brick Panel Install Back Molded Brick Panel/TraditionalInstall Side Molded Brick Panel Herring- bone Install Back Molded Brick Panel Herring- boneInstall Mortar Optional Install ScreensFinishing Hearth Extension= 1/k x inches of thickness Finishing Materials Non-combustibleFraming Material Equivalent insulationNon-combustible Sealant Use only non-combustible framing material below standoffs Finishing MaterialStandoffs Combustible MantelAngle Gas Code, Ansi Z223.1 Accessories Gas Log/Lighter Provision Wood Burning InsertsReference Materials Fireplace DimensionsID6 Insulated Duct Catalog # Chimney Components15-1/4 387 mm 31-3/4 806 mm 34-5/8 879 mm Heatilator Birmingham BIR42-B 4059-681 11/11 Herringbone Refractory Service PartsContact Information