Hearth and Home Technologies 8000TV-OAK-IPI owner manual Design and Installation Considerations

Page 17

B. Design and Installation Considerations

Heat & Glo B-type vent gas appliances are designed to operate with all exhaust gases expelled to the outside of the building, and combustion air pulled from the room.

Installation MUST comply with local, regional, state and national codes and regulations. Consult insurance carrier, local building inspector, fire officials or authorities having jurisdiction over restrictions, installation inspection and permits.

Before installing, determine the following:

•Where the appliance is to be installed.

•The vent system configuration to be used.

•Gas supply piping requirements.

•Electrical wiring requirements.

•Framing and finishing details.

•Whether optional accessories—devices such as a fan, wall switch, or remote control—are desired.

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. For assistance or additional information, consult a qualified service technician, service agency or your dealer.

C. Tools and Supplies Needed

Before beginning the installation be sure that the following tools and building supplies are available.

Tape measure

Framing material

Pliers

High temperature caulking material

Hammer

Phillips screwdriver

Gloves

Framing square

Voltmeter

Electric drill and bits (1/4 in.)

Plumb line

Safety glasses

Level

Reciprocating saw

Manometer

Flat blade screwdriver

Noncorrosive leak check solution

1/2 - 3/4 in. length, #6 or #8 Self-drilling screws One 1/4 in. female connection (for optional fan).

D. Inspect Appliance and Components

The following B-vent components are needed for instal- lation.

•Fireplace Box

•Pipe Components

•Firestops

•Attic Insulation Shield

•Elbows

•Strapping

•Roof Flashing or Chase Top

•Termination Cap

•Storm Collar

•Carefully remove the appliance and components from the packaging.

•The vent system components and decorative doors and fronts may be shipped in separate packages.

•If packaged separately, the log set and appliance grate must be installed.

•Report to your dealer any parts damaged in shipment, particularly the condition of the glass.

•Read all of the instructions before starting the instal- lation. Follow these instructions carefully during the installation to ensure maximum safety and benefit.

WARNING! Risk of Fire or Explosion! Damaged parts could impair safe operation. DO NOT install damaged, in- complete or substitute components. Keep appliance dry.

Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:

•Installation and use of any damaged appliance or vent system component.

•Modification of the appliance or vent system.

•Installation other than as instructed by Hearth & Home Technologies.

•Improper positioning of the gas logs or the glass door.

•Installation and/or use of any component part not approved by Hearth & Home Technologies.

Any such action may cause a fire hazard.

WARNING! Risk of Fire, Explosion or Electric Shock! DO NOT use this appliance if any part has been under water. Call a qualified service technician to inspect the appliance and to replace any part of the control system and/or gas control which has been under water.

Heat & Glo • 8000TV-OAK, 8000TV-OAK-IPI, 8000TVLP-OAKIPI • 2058-900 Rev. N • 11/08

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents What to do if you smell gas Models 8000TV-OAK 8000TV-OAK-IPI 8000TVLP-OAKIPIHomeowner Reference Information CongratulationsUser Guide Table of ContentsTroubleshooting Appliance SetupFinishing Reference MaterialsCONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Listing and Code Approvals Your Fireplace Gas Fireplace SafetyOperating Instructions User Guide Clear Space Fan Kit optionalOutside Air optional Before Lighting FireplaceFinal inspection by Lighting Instructions IPILighting Instructions Standing Pilot For Your Safety Read Before Lighting Lighting InstructionsAfter Fireplace is Lit Frequently Asked QuestionsMaintenance Tasks-Homeowner Maintenance and ServiceGlass Cleaning Remote ControlGasket Seal and Glass Assembly Inspection Maintenance Tasks-Qualified Service TechnicianVenting LogsEither cobrahead or SIT Typical Appliance System Getting StartedInspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Negative Pressure Selecting Appliance Location Framing and ClearancesClearances Constructing the Appliance ChaseCombustible Mantel Legs or Wall Projections Mantel and Wall ProjectionsCombustible Mantels Vent Termination Minimum Clearances Termination LocationsVent System Configuration Vent Information and DiagramsVent Guidelines Pipe Clearances to Combustibles Vent Clearances and FramingWall and Ceiling Penetration Framing Vertical Penetration FramingAppliance Preparation Installing Outside Air Kit Damper Assem- blyGas and Electrical Connections Securing and Leveling the ApplianceChecking Pilot Plate Completing Grate Set-upAssembly of Vent Sections Installing Vent PipeInstall Attic Insulation Shield Attaching Vent to FireboxFuel Conversion Gas InformationGas Pressure Gas ConnectionStanding Pilot Ignition System Wiring Wiring RequirementsIntellifire Ignition System Wiring Optional Accessories RequirementsIntellifire Pilot Ignition IPI Wiring Diagram Electrical Service and RepairWall Switch Installation for Fan Optional Junction Box InstallationFacing Material FinishingAppliance Setup Install the Log Assembly Log Assembly LOGS-8OAKPage Install the Mesh Fixed Glass AssemblyInstall Trim and/or Surround Install HoodStanding Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Action Symptom Possible Cause Corrective Action TroubleshootingIntellifire Ignition System Ues to spark, and main Reference Materials Appliance Dimension DiagramService Parts Log Set AssemblyAt Depot Service Parts List 8000TV-OAK, 8000TV-OAK-IPIStocked 8000TV-OAK-IPI8000TV-OAK Contact Information

8000TV-OAK, 8000TVLP-OAKIPI, 8000TV-OAK-IPI specifications

Hearth and Home Technologies has carved a notable niche in the world of home heating solutions, and their 8000TV-OAK-IPI, 8000TVLP-OAKIPI, and 8000TV-OAK models exemplify innovation, efficiency, and aesthetic appeal. Each model boasts unique features, yet they share a commitment to enhancing ambiance while ensuring effective warmth.

The 8000TV-OAK-IPI is designed with versatility in mind. It operates using an innovative IntelliFire® ignition system, which allows for easy startup and reliable performance. The model is compatible with natural gas and propane, giving homeowners the flexibility to choose based on their preferences. One of its key features includes the stunning oak finish, which complements a variety of interior designs, transforming any room into a cozy retreat. Its heat output is efficient, reaching up to 42,000 BTUs, which makes it perfect for larger spaces, ensuring consistent warmth throughout the area.

Similarly, the 8000TVLP-OAKIPI is tailored for those who prefer a liquid propane fuel source. It shares compatibility with advanced technology, featuring the IntelliFire® system that improves energy efficiency while minimizing the environmental impact. The design mirrors the oak aesthetics of its counterpart but adds functionality with customizable flame settings that allow homeowners to adjust the ambiance to their liking. This model also highlights a large viewing area, enabling a clear view of the vibrant flames while maximizing heat output.

The 8000TV-OAK model, while maintaining the traditional oak finish, sets itself apart with optional accessories such as decorative glass media, enabling personalization that caters to individual tastes. This model also benefits from advanced safety features, including an automatic shut-off system to ensure peace of mind during operation. The combination of practicality and style makes this option a popular choice.

All three models are equipped with exceptional insulation, resulting in lower energy costs. Their design encourages ease of maintenance; ash pans and glass cleanings have been simplified, ensuring that the upkeep of your hearth remains minimal. The integration of modern heating technology in these models illustrates Hearth and Home Technologies' dedication to combining craftsmanship with cutting-edge performance.

In conclusion, Hearth and Home Technologies' 8000TV-OAK-IPI, 8000TVLP-OAKIPI, and 8000TV-OAK models are perfect examples of how traditional aesthetics and modern technology can coalesce to create high-quality heating solutions. Designed with efficiency, safety, and ambiance in mind, these fireplaces are a worthy investment for anyone looking to enhance their living space with both warmth and style.
Top Page Image Contents