Hearth and Home Technologies BV4236DBI manual Maintenance and Service

Page 13

3 Maintenance and Service

Any safety screen or guard removed for servicing must be replaced prior to operating the fireplace.

When properly maintained, your fireplace will give you many years of trouble-free service. We recommend an- nual service by a qualified service technician.

A. Maintenance Tasks-Homeowner

Installation and repair should be done by a qualified service technician only. The fireplace should be inspected before use and at least annually by a professional service person.

The following tasks may be performed annually by the homeowner. If you are uncomfortable performing any of the listed tasks, please call your dealer for a service ap- pointment.

More frequent cleaning may be required due to lint from carpeting or other factors. Control compartment, burner and circulating air passageway of the fireplace must be kept clean.

CAUTION! Risk of Burns! The fireplace should be turned off and cooled before servicing.

Glass Cleaning

Frequency: Seasonally

By: Homeowner

Tools Needed: Protective gloves, glass cleaner, drop cloth and a stable work surface.

CAUTION! Handle fixed glass assembly with care. Glass is breakable.

•Avoid striking, scratching or slamming glass

•Avoid abrasive cleaners

•DO NOT clean glass while it is hot

•Prepare a work area large enough to accommodate fixed glass assembly and door frame by placing a drop cloth on a flat, stable surface.

Note: Fixed glass assembly and gasketing may have res- idue that can stain carpeting or floor surfaces.

•Remove door or decorative front from fireplace and set aside on work surface.

•See Section 14.I for instructions to remove fixed glass assembly.

•Clean glass with a non-abrasive commercially available cleaner.

-Light deposits: Use a soft cloth with soap and water

-Heavy deposits: Use commercial fireplace glass cleaner (consult with your dealer)

•Carefully set fixed glass assembly in place on fireplace. Hold glass in place with one hand and secure glass latches with the other hand.

•Reinstall door or decorative front.

Doors, Surrounds, Fronts

Frequency: Annually

By: Homeowner

Tools needed: Protective gloves, stable work surface

•Assess condition of screen and replace as necessary.

•Inspect for scratches, dents or other damage and repair as necessary.

•Check that louvers are not blocked.

•Vacuum and dust surfaces.

Remote Control

Frequency: Seasonally

By: Homeowner

Tools needed: Replacement batteries and remote con- trol instructions.

•Locate remote control transmitter and receiver.

•Verify operation of remote. Refer to remote control operation instructions for proper calibration and setup procedure.

•Place batteries as needed in remote transmitters and battery-powered receivers.

•Place remote control out of reach of children.

If not using your fireplace for an extended period of time (summer months, vacations/trips, etc), to prevent unin- tended operation:

•Remove batteries from remote controls.

•Unplug 6 volt transformer plug on IPI models.

•Remove battery backup from control module.

Venting

Frequency: Seasonally

By: Homeowner

Tools needed: Protective gloves and safety glasses.

•Inspect venting and termination cap for blockage or obstruction such plants, bird nests, leaves, snow, debris, etc.

•Verify termination cap clearance to subsequent construc- tion. See Section 6.

•Inspect for corrosion or separation.

•Verify weather stripping, sealing and flashing remains intact.

•Inspect draft shield to verify it is not damaged or missing.

Hearth & Home Technologies • BV4236DBI, BV4842DBI • 2209-900 Rev. N • 9/12

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Do Discardnot What to do if you smell gasHomeowner Reference Information CongratulationsXxxxxxxx User Guide Table of ContentsReference Materials TroubleshootingLimited Lifetime Warranty Limited Lifetime Warranty Hearth & Home Technologies IncWarranty Conditions Limited Lifetime WarrantyListing and Code Approvals Operating Instructions User Guide Gas Fireplace SafetyYour Fireplace Remote Controls, Wall Controls and Wall Switches Fixed Glass AssemblyIPI Battery Tray/Battery Installation Fan Kit optionalNine Hour Safety Shutdown Feature Module ResetControl Module Operation Before Lighting FireplaceFinal inspection by Lighting Instructions IPIDo not Connect Line Volt AGE 110/120 VAC or 220/240After Fireplace is Lit Frequently Asked QuestionsMaintenance and Service Gasket Seal and Glass Assembly Inspection Maintenance Tasks-Qualified Service TechnicianLogs FireboxCover Plates Lava Rock Basket, Grate and Valve As- sembly RemovalBurner Identification/Verification Typical Appliance System Getting StartedTools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components Negative Pressure Selecting Appliance Location Framing and ClearancesBV4236DBI BV4842DBIConstructing the Appliance Chase Minimum Framing DimensionsCombustible Mantels Clearances Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination LocationsVent Guidelines Vent Information and DiagramsPipe Clearances to Combustibles Vent Clearances and FramingWall and Ceiling Penetration Framing Vertical Penetration FramingInstalling the Non-combustible Board Installing Outside Air Kit Damper Assem- blyAppliance Preparation Gas and Electrical ConnectionsProper Positioning, Leveling And Securing Of An Securing and Leveling the ApplianceAssembly of Vent Sections Installing Vent PipeInstall Attic Insulation Shield Attaching Vent to FireboxFuel Conversion Gas InformationGas Pressure Gas ConnectionIntelliFire Plus Ignition System Wiring Wiring RequirementsOptional Accessories Requirements Electrical InformationElectrical Service and Repair Junction Box Wired to Wall Switch or BC10 Wall Switch Installation for Fan OptionalFacing Material FinishingCombustible Mantel Legs or Wall Projections Finishing Material Thickness 1 Inch Thick or Less DoorsFinishing Material Finishing Material Thickness Greater Than One Inch AnyAttaching Finishing Strips Attachment of Finishing StripsAppliance Setup Placement of Embers Ember PlacementLOG Placement Tabs LOG Placement Indentations Grate Tine Install the Log Assembly Log Assembly LOGS-BV36LOG Placement Slots LOG Placement Tabs Left Grate TineLOG Nose Right Grate TineFlat Area LOG #6 Contacts TOP of LOG #4 LOG Placement Indentations LOG Placement Tabs Grate Tine Install the Log AssemblySlots Grooves Left Grate Tine LOG #4 Contacts LOG #2 Horizontal Grate BARAir Shutter Setting Install Trim and/or SurroundAir Shutter Settings Symptom Possible Cause Corrective Action TroubleshootingIntelliFire Plus Ignition System Burner will not ignite Reference Materials Appliance Dimension DiagramCatalog # BV4236DBI BV4842DBI BV4236DBI , BV4842DBI Sold as Kit Only Contact Information

BV4236DBI specifications

The Hearth and Home Technologies BV4236DBI is a stunning direct vent gas fireplace that combines elegance with cutting-edge technology. Designed to enhance any living space, this fireplace provides a perfect blend of aesthetics and functionality, ensuring warmth and comfort during chilly evenings.

One of the standout features of the BV4236DBI is its contemporary design that offers a wide viewing area for the mesmerizing flames. With a sleek front and minimalistic frame, it fits seamlessly into modern home decor, making it an attractive focal point in any room. The large, unobstructed glass allows for maximum visibility of the fire, providing a cozy ambiance.

Performance-wise, the BV4236DBI boasts an impressive heating capacity. With a BTU output of up to 36,000, it effectively warms spaces ranging from medium to large. The efficiency of this fireplace ensures not only warmth but also reduced energy costs, making it an economical choice.

The BV4236DBI features advanced venting technology that allows for installation flexibility. The direct vent design draws air from the outside for combustion, ensuring that indoor air quality remains unaffected. This setup minimizes heat loss and creates a safe environment for users, making it suitable for homes of all types.

Another notable characteristic is the intuitive remote control and optional wall switch. This convenience feature allows users to easily adjust the flame height and heat output from anywhere in the room, ensuring customized comfort at the touch of a button. Additionally, the fireplace is equipped with an adjustable flame and media options, including decorative crushed glass or ceramic logs, which enhance the visual appeal.

Safety is a priority, and the BV4236DBI incorporates several safety features such as a built-in safety shutoff and an optional screen to prevent potential hazards. The fireplace's durable construction meets stringent safety standards, providing peace of mind for families.

In summary, the Hearth and Home Technologies BV4236DBI is a versatile, stylish, and efficient gas fireplace that offers an unmatched home heating experience. With its powerful performance, elegant design, and advanced technologies, it stands out as a prime choice for homeowners looking to elevate their living spaces with both comfort and sophistication. Whether for a cozy evening or a lively gathering, this fireplace provides the warmth and ambiance that every home deserves.
Top Page Image Contents