Hearth and Home Technologies BV4236DBI manual Burner will not ignite

Page 45

IntelliFire Plus™ Ignition System - (continued)

Symptom

Possible Cause

Corrective Action

 

 

 

 

A. A shorted or loose connection in flame

Verify all connections to wiring diagram in manual. Verify

4. Pilot lights but contin-

sensing rod.

connections underneath pilot assembly are tight. Verify

ues to spark, and main

 

flame sense or igniter wires are not grounding out to metal

burner will not ignite.

 

chassis, pilot burner, pilot enclosure or screen if present, or

(If the pilot continues

 

any other metal object.

to spark after the

 

 

B. Poor flame rectification or contaminated

With fixed glass assembly in place, verify that flame is en-

pilot flame has been lit,

flame sensing rod.

gulfing flame sensing rod on left side of pilot hood. Flame

flame rectification has

 

sensing rod should glow shortly after ignition. With a multi-

not occurred.)

 

 

meter, verify that current in series between module and

 

 

 

 

sense lead is at least 0.14 microamps. Verify correct pilot

 

 

orifice is installed and gas inlet is set to pressure specifi-

 

 

cations. Polish flame sensing rod with fine steel wool to

 

 

remove any contaminants that may have accumulated on

 

 

flame sensing rod.

 

 

 

 

C. Module is not grounded.

Verify module is securely grounded to metal chassis of ap-

 

 

pliance. Verify that wire harness is firmly connected to the

 

 

module.

 

 

 

 

D. Damaged pilot assembly or contami-

Verify that ceramic insulator around the flame sensing rod

 

nated flame sensing rod.

is not cracked, damaged, or loose. Verify connection from

 

 

flame sensing rod to white sensor wire. Polish flame sens-

 

 

ing rod with fine steel wool to remove any contaminants

 

 

that may have accumulated on flame sensing rod. Verify

 

 

continuity with a multimeter with ohms set at lowest range.

 

 

Replace pilot if any damage is detected.

 

 

 

Hearth & Home Technologies • BV4236DBI, BV4842DBI • 2209-900 Rev. N • 9/12

45

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Do Discardnot What to do if you smell gasCongratulations Homeowner Reference InformationXxxxxxxx User Guide Table of ContentsReference Materials TroubleshootingLimited Lifetime Warranty Limited Lifetime Warranty Hearth & Home Technologies IncWarranty Conditions Limited Lifetime WarrantyListing and Code Approvals Gas Fireplace Safety Operating Instructions User GuideYour Fireplace Remote Controls, Wall Controls and Wall Switches Fixed Glass AssemblyIPI Battery Tray/Battery Installation Fan Kit optionalNine Hour Safety Shutdown Feature Module ResetControl Module Operation Before Lighting FireplaceFinal inspection by Lighting Instructions IPIDo not Connect Line Volt AGE 110/120 VAC or 220/240After Fireplace is Lit Frequently Asked QuestionsMaintenance and Service Gasket Seal and Glass Assembly Inspection Maintenance Tasks-Qualified Service TechnicianLogs FireboxCover Plates Lava Rock Basket, Grate and Valve As- sembly RemovalBurner Identification/Verification Typical Appliance System Getting StartedDesign and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Negative Pressure Selecting Appliance Location Framing and ClearancesBV4236DBI BV4842DBIConstructing the Appliance Chase Minimum Framing DimensionsCombustible Mantels Clearances Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination LocationsVent Guidelines Vent Information and DiagramsPipe Clearances to Combustibles Vent Clearances and FramingWall and Ceiling Penetration Framing Vertical Penetration FramingInstalling the Non-combustible Board Installing Outside Air Kit Damper Assem- blyAppliance Preparation Gas and Electrical ConnectionsProper Positioning, Leveling And Securing Of An Securing and Leveling the ApplianceAssembly of Vent Sections Installing Vent PipeInstall Attic Insulation Shield Attaching Vent to FireboxFuel Conversion Gas InformationGas Pressure Gas ConnectionIntelliFire Plus Ignition System Wiring Wiring RequirementsOptional Accessories Requirements Electrical InformationElectrical Service and Repair Junction Box Wired to Wall Switch or BC10 Wall Switch Installation for Fan OptionalFinishing Facing MaterialCombustible Mantel Legs or Wall Projections Finishing Material Thickness 1 Inch Thick or Less DoorsFinishing Material Finishing Material Thickness Greater Than One Inch AnyAttaching Finishing Strips Attachment of Finishing StripsAppliance Setup Placement of Embers Ember PlacementLOG Placement Tabs LOG Placement Indentations Grate Tine Install the Log Assembly Log Assembly LOGS-BV36LOG Placement Slots LOG Placement Tabs Left Grate TineRight Grate Tine LOG NoseFlat Area LOG #6 Contacts TOP of LOG #4 Install the Log Assembly LOG Placement Indentations LOG Placement Tabs Grate TineSlots Grooves Left Grate Tine LOG #4 Contacts LOG #2 Horizontal Grate BARInstall Trim and/or Surround Air Shutter SettingAir Shutter Settings Troubleshooting Symptom Possible Cause Corrective ActionIntelliFire Plus Ignition System Burner will not ignite Reference Materials Appliance Dimension DiagramCatalog # BV4236DBI BV4842DBI BV4236DBI , BV4842DBI Sold as Kit Only Contact Information

BV4236DBI specifications

The Hearth and Home Technologies BV4236DBI is a stunning direct vent gas fireplace that combines elegance with cutting-edge technology. Designed to enhance any living space, this fireplace provides a perfect blend of aesthetics and functionality, ensuring warmth and comfort during chilly evenings.

One of the standout features of the BV4236DBI is its contemporary design that offers a wide viewing area for the mesmerizing flames. With a sleek front and minimalistic frame, it fits seamlessly into modern home decor, making it an attractive focal point in any room. The large, unobstructed glass allows for maximum visibility of the fire, providing a cozy ambiance.

Performance-wise, the BV4236DBI boasts an impressive heating capacity. With a BTU output of up to 36,000, it effectively warms spaces ranging from medium to large. The efficiency of this fireplace ensures not only warmth but also reduced energy costs, making it an economical choice.

The BV4236DBI features advanced venting technology that allows for installation flexibility. The direct vent design draws air from the outside for combustion, ensuring that indoor air quality remains unaffected. This setup minimizes heat loss and creates a safe environment for users, making it suitable for homes of all types.

Another notable characteristic is the intuitive remote control and optional wall switch. This convenience feature allows users to easily adjust the flame height and heat output from anywhere in the room, ensuring customized comfort at the touch of a button. Additionally, the fireplace is equipped with an adjustable flame and media options, including decorative crushed glass or ceramic logs, which enhance the visual appeal.

Safety is a priority, and the BV4236DBI incorporates several safety features such as a built-in safety shutoff and an optional screen to prevent potential hazards. The fireplace's durable construction meets stringent safety standards, providing peace of mind for families.

In summary, the Hearth and Home Technologies BV4236DBI is a versatile, stylish, and efficient gas fireplace that offers an unmatched home heating experience. With its powerful performance, elegant design, and advanced technologies, it stands out as a prime choice for homeowners looking to elevate their living spaces with both comfort and sophistication. Whether for a cozy evening or a lively gathering, this fireplace provides the warmth and ambiance that every home deserves.
Top Page Image Contents