Hearth and Home Technologies Aztec, Bravo owner manual Log Assembly LOGS-BRAVO

Page 39

Positioning the Logs

If the gas logs have been factory installed they should not need to be positioned. If the logs have been packaged separately, refer to the following instructions.

Log Assembly: LOGS-BRAVO

CAUTION: Logs are fragile! Care- fully remove the logs from the packaging.

Before placing logs, check that the sensor on the pilot assembly does not contact the burner.

Remove shipping bracket and tie straps from the burner and grate.

Place the lava rock on the bottom of the firebox. Evenly spread the lava rocks with your hand.

2

4

5

6

1

3

 

 

 

 

 

Figure 12.20

Figure 12.20

LEFT LOG

TAB

SENSOR

RIGHT LOG

TAB

TIE STRAPS

GRATE

BURNER

Shipping Bracket

Figure 12.20

ADJUST LOG SO

GROOVE FOR

SURFACE IS FLUSH

LOG #2

1

TAB

1

Figure 12.20

Figure 12.20

LOG #1 (SRV750-703):Place log #1 between log tabs on left side and right side of the burner. Place such that bottom surface of log rests on burner surface (left).

704-936C

Hearth & Home Technologies, Inc. • Bravo, Aztec • InD • 703-900 Rev. N • 8/06

39

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Models Aztec Bravo Homeowner Reference Information CongratulationsTable of Contents Glass Specifications High Altitude Installations1Listing and Code Approvals Appliance CertificationTools and Supplies Needed Design and Installation ConsiderationsGetting Started Inspect Appliance and ComponentsSelecting Appliance Location Framing and ClearancesConstructing the Appliance Chase ClearancesClearance to Combustibles Mantel Projections Termination Locations Vent Termination Minimum ClearancesSee .4 for specific clearances Appliance Alcove ApplicationsMeasuring Standards Vent Information and DiagramsVent Table Key Use of ElbowsV1 Minimum H1 + H2 Maximum Vent DiagramsTop Vent Horizontal Termination One Elbow Minimum MaximumV1 + V2 Minimum H1 + H2 Maximum Í Top Vent Horizontal Termination Three ElbowsFlue Outlet Top Vent Vertical Termination No Elbow V1 = 46 ft. Max .0 mV1 Minimum H1 Maximum H1 + H2 Top Vent Vertical TerminationNon-Combustible Wall Penetration Vent Clearances and FramingPipe Clearances to Combustibles Wall Penetration Framing Combustible Wall PenetrationInstalling the Ceiling Firestop Installing Attic ShieldVertical Penetration Framing Securing and Leveling the Appliance Appliance PreparationAssembling Pipe Sections Installing Vent PipeAssembly of Vent Sections Attaching Vent to the Firebox AssemblyAssembling DVP-12A Slip Sections Assembling Minimum Installations MI SectionsDisassembly of Vent Sections Securing the Vent Sections Vertical SectionsHorizontal Sections Installing Heat Shield and Horizontal Termination Cap Installing the Horizontal Termination CapHeat Shield Requirements for Horizontal Termination 13 Minimum Height from Roof to Lowest Discharge Opening Installing Roof Flashing and Vertical Termination Cap16 Assembling the Storm Collar Around the Pipe Assembling and Installing Storm CollarPressure Natural Gas Propane Gas InformationFuel Conversions Gas Connection Gas PressuresHigh Altitude Installations Wall Switch Required Recommendation for WireConnecting to the Appliance Intellifire Ignition System WiringIntellifire Pilot Ignition IPI Wiring Diagram Wall Switch Installation for Fan Optional Junction Box InstallationFacing Material 11FinishingFinishing Styles Option a Flush Wall FinishOption B Kiva-style Arch Option C Southwestern kiva-style Option D Flush Wall Finish with Luxor Surround Flush wall installation with Luxor SurroundLava Rock and Ember Placement Appliance SetupClean the Appliance AccessoriesPositioning the Logs Log Assembly LOGS-AZTECGrooves For LOG #4 Grooves For LOG #7 Log Assembly LOGS-BRAVO Right Grate Tine LOG #6 Shutter Settings Glass AssemblyRemoving Glass Assembly Replacing Glass AssemblyBefore Lighting Appliance Operating InstructionsAnce Turn off all electric power to the appliLighting Appliance Intellifire IgnitionFrequently Asked Questions Initial Break-in ProcedureAfter Appliance is Lit Troubleshooting Intellifire Ignition SystemSympton Possible Cause Corrective Action Symptom Possible Cause Corrective Action Maintaining and Servicing Appliance Recommend addition of screen if one is not present Inspect Mantenance TasksReference Materials Appliance Dimension DiagramDVP45 45 Elbow Vent Components DiagramsDVP-TRAPK2 RF6M DVP and SL Series ComponentsService Parts List Log Set Assembly14 12 16 Aztec Additional service part numbers may appear on the followingLog Set Assembly Service PartsBravo Intermittent Pilot Ignition AZTEC, BravoBravo GAS Appliance Products Limited Lifetime WarrantyConditions, Exclusions, & Limitations of Liability Limited Lifetime WarrantyYear Limited Warranty How to Obtain ServiceContact Information For safe installation Operation

Bravo, Aztec specifications

Hearth and Home Technologies, a leader in the fireplace and heating industry, offers a remarkable range of products designed to meet the diverse needs of homeowners. Among their distinguished offerings are the Aztec and Bravo series of gas fireplaces, known for their blend of aesthetic appeal, efficiency, and innovative technologies.

The Aztec series stands out with its sophisticated design and versatile installation options. Available in multiple sizes, the Aztec fireplaces are adaptable to different spaces, allowing homeowners to choose a model that complements their interior design. A notable feature of the Aztec series is its captivating flame presentation, which is enhanced by state-of-the-art flame control technology. This technology allows users to adjust the intensity of the flames, creating the perfect ambiance for any occasion.

In addition to its striking visuals, the Aztec series is engineered for energy efficiency. Utilizing a highly efficient gas burner, these fireplaces provide substantial heat output while minimizing energy consumption. The inclusion of advanced ceramic glass helps improve heat retention, allowing more warmth to stay within the room and reducing overall energy costs. Moreover, the integrated fan system ensures optimal airflow, enhancing heat distribution throughout the living space.

The Bravo series, on the other hand, introduces an equally impressive set of features that appeal to both style and functionality. Bravo fireplaces are designed with a contemporary aesthetic in mind, featuring sleek lines and modern finishes. They come equipped with customizable options, allowing homeowners to personalize their fireplace with various door styles and frame finishes.

One of the standout characteristics of the Bravo series is its powerful heating capabilities. These fireplaces are built with advanced burner technology that delivers impressive heat output, making them suitable for larger areas. Furthermore, the Bravo series incorporates a user-friendly control system, granting users the convenience of adjusting settings via a remote control or smartphone app, enhancing the overall experience.

Both the Aztec and Bravo series are constructed with high-quality materials, ensuring durability and long-lasting performance. Hearth and Home Technologies prioritize safety and ease of use, and both series include safety features such as automatic shut-off mechanisms and child safety locks.

In conclusion, Hearth and Home Technologies’ Aztec and Bravo series offer exceptional choices for homeowners seeking stylish and efficient gas fireplaces. Their combination of advanced technologies, aesthetic versatility, and user-friendly features make them noteworthy contenders in the market, elevating the experience of warmth and comfort in any home setting.
Top Page Image Contents