Hearth and Home Technologies Aztec, Bravo owner manual Symptom Possible Cause Corrective Action

Page 47

Intellifire Ignition System - (continued)

Symptom

Possible Cause

Corrective Action

 

 

 

3. (Continued) - Pilot lights

b. Poor flame rectification or contaminated

Verify that flame is engulfing sensor rod. If the pilot assem-

but continues to spark,

sensor rod.

bly does not have a ground strap, consider installing one

and main burner will not

 

to increase flame rectification. Verify correct pilot orifice is

ignite. (If the pilot contin-

 

installed and inlet gas specifications. Flame carries recti-

ues to spark after the pilot

 

fication current, not the gas. If flame lifts from pilot hood,

flame has been lit, flame

 

the circuit is broken. A wrong orifice or too high an inlet

rectification has not oc-

 

pressure can cause pilot flame to lift. The sensor rod may

curred.)

 

be contaminated. Clean sensor rod with emery cloth.

 

 

 

3. (Continued) Pilot lights

c. Module is not grounded.

Verify that module is securely grounded to metal chassis

but continues to spark,

 

of appliance. Verify that wire harness is firmly connected to

and main burner will not

 

module.

ignite. (If the pilot contin-

 

 

ues to spark after the pilot

d. Damaged pilot assembly or dirty sensor

Verify that ceramic insulator around the sensor rod is not

flame has been lit, flame

rod.

cracked, damaged, or loose. Verify connection from sen-

rectification has not oc-

 

sor rod to white sensor wire. Clean sensor rod with emery

curred.)

 

cloth to remove any contaminants that may have accumu-

 

 

lated on sensor rod. Verify continuity with a multimeter with

 

 

ohms set at lowest range.

 

 

 

 

e. Faulty module.

Turn ON/OFF rocker switch or wall switch to OFF posi-

 

 

tion. Remove ignitor wire “I” from module. Place ON/OFF

 

 

Rocker switch or wall switch in ON position. Hold ground

 

 

wire about 3/16 inch away from “I” terminal on module. If

 

 

there is no spark at “I” terminal module must be replaced.

 

 

If there is a spark at “I” terminal, module is fine. Inspect

 

 

pilot assembly for shorted sparker wire or cracked insulator

 

 

around electrode.

 

 

 

4. Pilot sparks, but Pilot

a. Correct gas supply.

Verify that incoming gas line ball valve is “open”. Verify that

will not light.

 

inlet pressure reading is within acceptable limits, inlet pres-

 

 

sure must not exceed 14 in. W.C.

 

 

 

 

b. Ignitor gap is too large.

Verify that spark gap from ignitor to pilot hood is .17 in. or

 

 

1/8 in.

 

 

 

 

c. Module is not grounded.

Verify module is securely grounded to metal chassis of

 

 

appliance.

 

 

 

 

d. Module voltage output / Valve/Pilot

Verify battery voltage is at least 2.7 volts. Replace batter-

 

solenoid ohms readings.

ies if voltage is below 2.7.

 

 

 

Hearth & Home Technologies, Inc. • Bravo, Aztec • InD • 703-900 Rev. N • 8/06

47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Models Aztec Bravo Homeowner Reference Information CongratulationsTable of Contents Glass Specifications High Altitude Installations1Listing and Code Approvals Appliance CertificationTools and Supplies Needed Design and Installation ConsiderationsGetting Started Inspect Appliance and ComponentsSelecting Appliance Location Framing and ClearancesClearance to Combustibles Constructing the Appliance ChaseClearances Mantel Projections See .4 for specific clearances Termination LocationsVent Termination Minimum Clearances Appliance Alcove ApplicationsMeasuring Standards Vent Information and DiagramsVent Table Key Use of ElbowsV1 Minimum H1 + H2 Maximum Vent DiagramsTop Vent Horizontal Termination One Elbow Minimum MaximumV1 + V2 Minimum H1 + H2 Maximum Í Top Vent Horizontal Termination Three ElbowsFlue Outlet Top Vent Vertical Termination No Elbow V1 = 46 ft. Max .0 mV1 Minimum H1 Maximum H1 + H2 Top Vent Vertical TerminationNon-Combustible Wall Penetration Vent Clearances and FramingPipe Clearances to Combustibles Wall Penetration Framing Combustible Wall PenetrationVertical Penetration Framing Installing the Ceiling FirestopInstalling Attic Shield Securing and Leveling the Appliance Appliance PreparationAssembling Pipe Sections Installing Vent PipeAssembly of Vent Sections Attaching Vent to the Firebox AssemblyAssembling DVP-12A Slip Sections Assembling Minimum Installations MI SectionsHorizontal Sections Disassembly of Vent SectionsSecuring the Vent Sections Vertical Sections Heat Shield Requirements for Horizontal Termination Installing Heat Shield and Horizontal Termination CapInstalling the Horizontal Termination Cap 13 Minimum Height from Roof to Lowest Discharge Opening Installing Roof Flashing and Vertical Termination Cap16 Assembling the Storm Collar Around the Pipe Assembling and Installing Storm CollarPressure Natural Gas Propane Gas InformationFuel Conversions Gas Connection Gas PressuresHigh Altitude Installations Wall Switch Required Recommendation for WireConnecting to the Appliance Intellifire Ignition System WiringIntellifire Pilot Ignition IPI Wiring Diagram Wall Switch Installation for Fan Optional Junction Box InstallationFacing Material 11FinishingOption B Kiva-style Arch Finishing StylesOption a Flush Wall Finish Option C Southwestern kiva-style Option D Flush Wall Finish with Luxor Surround Flush wall installation with Luxor SurroundLava Rock and Ember Placement Appliance SetupClean the Appliance AccessoriesPositioning the Logs Log Assembly LOGS-AZTECGrooves For LOG #4 Grooves For LOG #7 Log Assembly LOGS-BRAVO Right Grate Tine LOG #6 Shutter Settings Glass AssemblyRemoving Glass Assembly Replacing Glass AssemblyBefore Lighting Appliance Operating InstructionsAnce Turn off all electric power to the appliLighting Appliance Intellifire IgnitionAfter Appliance is Lit Frequently Asked QuestionsInitial Break-in Procedure Sympton Possible Cause Corrective Action TroubleshootingIntellifire Ignition System Symptom Possible Cause Corrective Action Maintaining and Servicing Appliance Recommend addition of screen if one is not present Inspect Mantenance TasksReference Materials Appliance Dimension DiagramDVP45 45 Elbow Vent Components DiagramsDVP-TRAPK2 RF6M DVP and SL Series Components14 12 16 Service Parts ListLog Set Assembly Aztec Additional service part numbers may appear on the followingLog Set Assembly Service PartsBravo Intermittent Pilot Ignition AZTEC, BravoBravo GAS Appliance Products Limited Lifetime WarrantyConditions, Exclusions, & Limitations of Liability Limited Lifetime WarrantyYear Limited Warranty How to Obtain ServiceContact Information For safe installation Operation

Bravo, Aztec specifications

Hearth and Home Technologies, a leader in the fireplace and heating industry, offers a remarkable range of products designed to meet the diverse needs of homeowners. Among their distinguished offerings are the Aztec and Bravo series of gas fireplaces, known for their blend of aesthetic appeal, efficiency, and innovative technologies.

The Aztec series stands out with its sophisticated design and versatile installation options. Available in multiple sizes, the Aztec fireplaces are adaptable to different spaces, allowing homeowners to choose a model that complements their interior design. A notable feature of the Aztec series is its captivating flame presentation, which is enhanced by state-of-the-art flame control technology. This technology allows users to adjust the intensity of the flames, creating the perfect ambiance for any occasion.

In addition to its striking visuals, the Aztec series is engineered for energy efficiency. Utilizing a highly efficient gas burner, these fireplaces provide substantial heat output while minimizing energy consumption. The inclusion of advanced ceramic glass helps improve heat retention, allowing more warmth to stay within the room and reducing overall energy costs. Moreover, the integrated fan system ensures optimal airflow, enhancing heat distribution throughout the living space.

The Bravo series, on the other hand, introduces an equally impressive set of features that appeal to both style and functionality. Bravo fireplaces are designed with a contemporary aesthetic in mind, featuring sleek lines and modern finishes. They come equipped with customizable options, allowing homeowners to personalize their fireplace with various door styles and frame finishes.

One of the standout characteristics of the Bravo series is its powerful heating capabilities. These fireplaces are built with advanced burner technology that delivers impressive heat output, making them suitable for larger areas. Furthermore, the Bravo series incorporates a user-friendly control system, granting users the convenience of adjusting settings via a remote control or smartphone app, enhancing the overall experience.

Both the Aztec and Bravo series are constructed with high-quality materials, ensuring durability and long-lasting performance. Hearth and Home Technologies prioritize safety and ease of use, and both series include safety features such as automatic shut-off mechanisms and child safety locks.

In conclusion, Hearth and Home Technologies’ Aztec and Bravo series offer exceptional choices for homeowners seeking stylish and efficient gas fireplaces. Their combination of advanced technologies, aesthetic versatility, and user-friendly features make them noteworthy contenders in the market, elevating the experience of warmth and comfort in any home setting.
Top Page Image Contents