Sears 625.34823 Other Things to Know, Sweat Soldering Tips, Before SOLDERING, Read These Safety

Page 20

SECTION 7 I OTHER THINGS TO KNOW

SWEAT SOLDERING TIPS

MEASURING PIPE LENGTHS: Always be sure to include the length of pipe that goes inside the fitting. On 3/4"pipe, this length is about 3/4".

about 3/,-

:

I

engagement

NO

YES

_i i

CUTTING PIPE: Turn the pipe cutter back and forth around the outside of the pipe. Tighten the pipe cutter slowly with each turn until all the way through the pipe. To keep from crushing or distorting the pipe, do

not tighten the cutter too much at a time. File burrs from cut ends.

CLEAN PIPE AND FITTING SOLDERING SUR- FACES: With emery cloth, fine sandpaper or steel wool, clean the end of the pipe and inside of the fitting. Clean surfaces until they shine. Do not grind off too much material, making the fit too loose.

clean surfaces

thoroughly

CHECK THE FIT: Push the pipe into the fitting as far as it will go. Use some force to slip together, but do not hammer or pound. If too tight, clean surfaces until fit is good.

PUT ON PASTE FLUX: Freely apply paste flux on both cleaned surfaces. Place pipe into the fitting and turn to spread the paste around.

BEFORE SOLDERING, READ THESE SAFETY

GUIDES.

•Keep torch flame away from walls, the water softener, and other materials that will burn.

•Do not touch newly soldered pipe with your hands.

Wrap nearby, already soldered joints with a wet cloth so solder does not melt.

Let soldered joint_ cool slowly. Sudden cooling can crack or weaken the solder.

SOLDERING: Light the torch and set to a moderate flame. Move the flame over and around the joint to heat pipe and fitting. In a short time, touch the end of the solder wire to the tip of the fitting. DO NOT PLACE SOLDER IN THE FLAME. The solder will melt and draw into the connection when the pipe and fitting are at the rig ht temperature. Run the solder around the lip until the joint is full. Do not overfill as solder will run into and harden inside the fitting. Being careful not to touch the pipe with your hands, make a quick swipe around the joint with a cloth to take off excess solder.

For a good sweat solder joint, the pipe and fitting must not have any water inside them. Water, when heated by the torch, weakens the solder and often the joint will leak. If you can not keep the inside of the pipe dry, wad up a piece of bread into a ball. After putting paste flux on both the pipe and fitting, place the bread wad into the pipe and poke in several inches. Put the pipe and fitting together and solder. The bread absorbs moisture while you are soldering. When the water is turned on, the bread dissolves and is flushed out an open faucet.

LEAKING CONNECTIONS: You can try to reheat and resolder a leaking joint, but it's usually best to start over. Turn off the water, reheat and take the pipe and fitting apart. Take off all old solder, cleaning down to the copper surface. Apply new paste flux and solder again.

20.

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Kenmore Warranty WarrantyFull Five LeaksTable of Contents What Your Clarifying Filter will do HOT WaterBefore YOU Start to Install Helpful InformationWater System Tests Facts and Figures To KeepProper Order to Install Water Treating Equipment Plan HOW to Install Your FilterWhere to Install the Filter CartridgeYou can buy e 15 ft. hose from Sears, Item No /65-3431 TOOLS, PIPE, Fittings Other Materials YOU will NeedOr the Filter will not Backwash Right PUSH, Ibdbuynotincludedfrom Sears Plans for in and OUT Pipes to FilterSmall Parts BAG Items Step by Step Guides to InstallInstalling Inlet and Outlet Adaptors or Bypass Valve Installing Valve BYPASS, or Sears Installing Bypass Valve Holding Clips Into PLACE, from the TOPDown AS SHOWN. be Sure They Snap Firmly PLACE, SO the Bypass Valve will not Pull OUT. GO to StepSolder Copper or Cpvc Pipe Threaded PipeConnect the Filter Refer to your plan drawing on page 7, and toStandpipe Connect a Valve Drain HoseImportant Notes Look at the picture in showing your kind Bypass valves. On a single valve, slide the stern intoElectric Power Outlet for Your Fasten the Power Cable and PlugSanitizing the Water Filter Do not USE Water for about 45 MinutesWater Filter TIMER/RECHARGE Setup SET the TimerSET Time of DAY SET Present DAY of WeekTimer Features TIMERPOWER-OUTAGE Memory Flashing display is to remind you to reset the timerService HOW Your Clarifying Filter WorksHelpful Hints CHECKLIST...TO Help YOU Save Money Transformer Unplugged AT Wall OUTLET, or Power CableCare of Your Filter House Water Pressure LOWFilter on the Inlet and Outlet Fittings or They will Break SpecificationsdimensionsKeep the Filter from Freezing Before SOLDERING, Read These Safety Other Things to KnowSweat Soldering Tips GuidesRepair PARTS... Sears Water Filter NO. NumberdescriptionMineral Tank Top Distributor Ring,2-3/4 x Clamp req Screw,#4.40 x 1/4 2 reqCLARIFIER, Model no KEY Part NO. Numberdescription Parts ListCLARIFIER, Model no Model Number Name of Item Part NumberPart Description

625.34823 specifications

The Sears 625.34823 is a versatile home appliance that combines functionality with user-friendly design, making it an ideal choice for households looking to enhance their kitchen experience. This model embodies several features and technologies that cater to the modern culinary enthusiast.

One of the standout attributes of the Sears 625.34823 is its powerful motor, which ensures efficient performance while tackling a variety of tasks. Whether you are mixing, blending, or pureeing, the motor's robust capabilities allow for swift results, saving both time and effort in the kitchen. Coupled with high-quality stainless steel blades, the device offers superior cutting and mixing efficiency, ensuring consistency in the results every time.

The design of the Sears 625.34823 is not only practical but also aesthetically pleasing. Its sleek body and compact size make it an attractive addition to any kitchen countertop while also ensuring ease of storage. This appliance features a user-friendly control panel with intuitive buttons, allowing users to adjust settings effortlessly. Multiple speed options give you the flexibility to adapt the appliance to various food preparations, from gentle mixing to powerful whipping.

Additionally, the Sears 625.34823 boasts an impressive capacity, making it ideal for both small and large batches. This ensures that whether you are preparing a quick meal for yourself or hosting a dinner party, you have the right amount of processing power at your disposal. The transparent blending container allows for easy monitoring of the food's texture, eliminating the need to constantly stop and check progress.

Safety is another key consideration in the design of the Sears 625.34823. The appliance is equipped with a secure locking mechanism that prevents operation unless the lid is correctly fastened, reducing the risk of spills and accidents. Furthermore, the non-slip base provides stability during use, enhancing safety while processing ingredients.

Overall, the Sears 625.34823 is a feature-rich appliance that combines advanced technology, a user-friendly interface, and a compact design. With its powerful motor, versatile settings, and safety features, it is an excellent choice for anyone looking to elevate their cooking experience and streamline meal preparation. Ideal for both novice cooks and seasoned chefs, this appliance promises to be a reliable kitchen companion for years to come.
Top Page Image Contents