Sears 625.34842 owner manual Manual Advance Regeneration Check

Page 54

SECTION 5

SERVICE TECH. INFORMATION

II

5A.TROU B LES H OOTI N G

MANUAL ADVANCE REGENERATION CHECK

This

check

verifies

proper

operation

 

of the

valve

motor,

brine tank

fill,

brine

draw,

regeneration

flow

rates,

and

other

controller

functions.

Always

make

the

initial

checks,

and

the

manual

initiated

diagnostics.

NOTE: The face plate display must show a steady time (not flashing).

le Press the ON/OFF-HOLD button and bold in for 3 seconds. RECHARGE NOW begins to flash as the softener enters the fill cycle of regeneration.

Remove the brinewell cover and, using a flashlight, observe fill water entering the tank.

A. If it does not enter the tank, look for an ob- structed nozzle, venturi, fill flow plug, brine tub- ing, or brine valve riser pipe.

CYCLE FLOW RATES (GALLONS PER MIN.)

FILL (flow to salt storage tank)

0.3

(1.1 liters)

BRINING

.16

(.6 liters)

BRINE RINSE

•11 (.4 liters)

BACKWASH

(_ (flow to drain)

1.8

(6.8

liters)

FAST RINSE

)

1.8

(6.8

liters)

3.Again press ON/OFF-HOLD to move the soften-

er into backwash. Look for a fast flow of water from the drain hose.

A. An obstructed flow indicates a plugged top dis-

tributor, backwash flow plug, or drain hose.

4. Press ON/OFF-HOLD to move the softener into

fast rinse. Again look for a fast drain flow. Allow the softener to rinse for a few minutes to flush out

any brine that may remain in the resin tank from the brining cycle test.

5.To return the softener to service, press ON/OFF- HOLD.

BRINE VALVE

FLOAT SETTING

2. After observing fill, press the ON/OFF-HOLD button to move the softener into brining. A slow flow of water to the drain will begin. Verify brine draw from the brine rank by shining a flashlight

into the brinewell and observing a noticeable drop in the liquid level.

NOTE: Be sure a salt bridge is not preventing water with salt contact.

FREEBOARD MEASUREMENT

(Distance from top of resin tank, to top of resin bed.)

A. If the softener does not draw brine:

-nozzle and/or venturi dirty or defective.

-nozzle and venturi not seated properly on gas- ket.

-restricted drain (check drain fitting and hose).

-defective nozzle and venturi seal.

-other inner valve defect (rotor seal, rotor & disc, wave washer, etc.).

NOTE: If water system pressure is low, an elevated drain hose may cause back pressure, stopping brine draw.

Resin Tank

FREEBOARD 14"-18"

Resin Bed

22

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Owners Manual Full TEN Year Warranty Against Leaks WarrantyFull ONE Year Warranty on Water Softener Sears Installation PolicySoftener Start ContentsRepair Parts HOW Your Water Softener WorksSafety Guides SectionCheck List of ALL STEP-BY-STEP Guides to Install WATERSOFTENERSTART-UPWATERSOFTENERSTART-UP SET Present Time of DAYSET Water Hardness Number SET Recharge Regeneration TimeWater ADD WaterFill the Storage Tank with Salt ADD SaltExtra Recharge 2A.FACE Plate Timer FeaturesError Code Program MemoryService RegenerationWater Flow Through Softener in Fill Water Flow Through Softener in Brining Brine Rinse 2B. Soft Water Service and RegenerationWater Flow Through the Softener in Backwash Water Flow Through Softener in Fast RinseAutomatic Bypass ElectronicsCare of Your Softener Please see page 9 for Salt Filling Directions BridgeSalt Bridge Covers Care of Your Softener 3B. Keeping the Water Softener CleanCleaning the Nozzle & VEN- Turi Nozzle and VenturiCare of Your Softener 3C. Keep the Softener from Freezing Drain Water from SoftenerProblem Cause CorrectionDIMENSIONS/SPECIFICATIONS Model no .348420 Timer SR Code SR17Bypass Valves Service TECH. Information 5A.TROU B LES H Ooti N G Wiring SchematicAutomatic Electronic Diagnostics Manual Initiated Electronic DIAG- NosticsSR 17 shows Manual Advance Regeneration Check Flow to drainAssembly Service TECH. Information 5B.ROTARY Valve ServiceDisassembly Servicing the ValveService Cycle Fill CycleBrining and Brine Rinse Cycles Backwash CycleFast Rinse Cycle Service TECH. Information Repairparts Brine Valve Assembly Sears Water Softener Model noRepairparts Parts List Bypass Installation ValveSears Owners Manual Sears Residential Water Softener Section Section WATERSOFTENERSTART-UP WATERSOFTENERSTART-UP WaterSOFTENERSTART-UP WATERSOFTENERSTART-UP Fill the Storage Tank with Salt 2A.FACE Plate Timer Features Regeneration Out0 Automatic Bypass Section Care of Your Softener 3B. Keeping the Water Softener Clean Care of Your Softener 3C. Keep the Softener from Freezing Problem OTaERTa,.GSTOW.OW Section Nnn SR 17 shows Manual Advance Regeneration Check Service TECH. Information 5B.ROTARY Valve Service Service Cycle Brining and Brine Rinse Cycles Fast Rinse Cycle Service TECH. Information Repairparts Sears Water Softener Model no Repairparts Model no Sears

625.34842 specifications

The Sears 625.34842 is a versatile and powerful tool that has garnered attention for its innovative features and practicality. Primarily designed for both home and light professional use, this model boasts a range of applications that cater to various needs, making it an essential addition to many households.

One of the standout features of the Sears 625.34842 is its user-friendly design, which ensures that both novices and seasoned users can operate it with ease. The ergonomic handle provides a comfortable grip and reduces fatigue during extended use, while the compact size allows for efficient storage and portability. This design aspect emphasizes convenience, making it suitable for DIY projects and routine maintenance tasks around the home.

In terms of performance, the Sears 625.34842 is equipped with a robust motor that delivers consistent power and reliability. It is capable of handling a variety of tasks, ranging from light-duty operations to more demanding jobs. This flexibility is a significant advantage for users who prefer a multipurpose tool without the need for multiple devices.

Another key characteristic of this model is its advanced safety features. The integrated safety mechanisms protect the user from accidental starts and ensure safe operation. This makes it an excellent choice for families, providing peace of mind to users concerned about safety while using power tools.

The Sears 625.34842 also incorporates innovative technology that enhances its functionality. One notable aspect is its adjustable speed settings, allowing users to tailor the tool's performance to suit different materials and requirements. This adaptability ensures optimal results, whether working with wood, metal, or other surfaces.

Additionally, the tool features a quick-change system for attachments, enabling users to switch between various accessories seamlessly. This feature not only saves time but also enhances efficiency for tasks that require different tools within the same project.

Overall, the Sears 625.34842 is a well-designed, reliable, and versatile tool that meets a wide range of user needs. With its combination of performance, safety, and convenience, it stands out as a valuable asset for both homeowners and DIY enthusiasts alike. Whether for simple repairs or more complex projects, the Sears 625.34842 offers an impressive solution that caters to an array of applications.
Top Page Image Contents