Sears 1700 manual LKeil,B, Pivot Pin, ==ilrd

Page 7

Turnhandleclockwiseuntilithaspiercedthewater lineandvalveiscompletelyclosed(Fig.16).

, _ PartiallyuncoilthetubingSlidethebrasscompres.- sionnutoverthetubingThethreadsinthenutmustfacethe.

tubingend.Placethebrasscompressionsleeveasshownin

Fig. 16. Slip brass insert into end of tubing.

_ U Insert the tubing end into the saddle valve at threaded stem "A" (Fig. 16) as far as it will go. Thread the brass compression nut onto the valve, then tighten gently with a wrench. Take care not to overtighten the nut.

l;Ke'_il[,_B

Brass Compression

Sleeve

 

 

f

Brass Insert

Brass

Compression Nut

NOTE: Wire bearing support must be bent slightly inward to insure snug engagement of media wheel with media motor. Adjust as required by bending wire slightly inward before installing media wheel. (Be careful not to overbend as too much tension may cause media wheel shaft to pop out of plastic bearing.)

1,1[_ U:!

Cover

Bend

Slightly _.

Inward

 

 

Media

Reservoir

Overflow

Wheel

 

Compartment

Assembly

Water Pipe

.A,,

Rubber Gasket

(Stem Up)

MOUNTING SADDLE VALVE

7Unwind the rest of the tubing. Take care not to kink it. Run the tubing along flat surfaces to the humidifier. Support the tubing as needed to avoid contact with furnace.

0

__ O Close previously opened faucet. Turn on main wa- ter supply. Place a pail under the end of the tubing. Open the

saddle valve. Flush the line. Make sure there are no leaks along the line or at the valve. Turn valve off.

11 Install float assembly. Place float assembly on valve

body; align hole. Slide pivot pin through holes to fasten. Float should have slight up and down movement (Fig. 19).

Operating Float \

Valve Button

Body

Pivot Pin

Complete installation of water supply by first sliding plastic compression nut onto the water supply tubing. Insert brass insert into the end of water supply tubing. Insert the tubing into humidifier valve body, making sure it is fully seated. Tighten plas- tic nut securely, finger tight (no wrench) (Fig. 17).

l=[_=_ilrd

Plastic Compression Nut

[ 12 Open saddle valve and allow reservoir to fill. Check water level (Fig. 20). If adjustment is necessary, turn off water and remove float assembly. See instructions on bottom of float. To raise water level, turn float clockwise viewing bottom of float. Water should be 9/16" below the top edge of the reservoir.

t--p,ost,o

3rass Insert

Water Line

WARNING:

BrassInsert MustBe Installed

10 Install reservoir, making sure overflow drain is on

left side. Install media wheel. Be sure that media wheel is prop- erly engaged with the media motor and that media wheel shaft is in groove in plastic bearing (Fig. 18).

3 Lower top cover. Install plastic front cover by inserting

top edge up under top cover front flange, with side flanges out- side casing. Swing bottom of cover in against case and lower down against flange.

7

Image 7
Contents Kenmore Installation Maintenance Repair Parts TroubleshootingContents Typical Questions Asked Understanding HumiditySelecting a location DisassemblyInspection Fiber Plenum Ducts MotorBracketWater Supply InstallationPivot Pin LKeil,B==ilrd Wall mount Fig Install humidistat on hot air plenumHumidistat Cold air plenum mount F g21Operation MaintenanceServicing the Float Service hintsSummer Shut Down Fall Start UPKEY Part Description Repair partsKenmore 1700 Central Humidifier Model noKenmore 303.14601 Furnace Humidifier Maintenance Kenmore For the repair or replacement parts you need

1700 specifications

The Sears 1700 is a remarkable piece of technology that emerged during its heyday, capturing the attention of consumers with its innovative features and robust performance. Introduced in the late 20th century as part of Sears' commitment to offering quality products, the 1700 quickly established itself as a reliable option for those seeking an efficient and user-friendly appliance.

One of the most notable features of the Sears 1700 is its powerful motor, which allows for efficient operation across a range of tasks. Whether it’s tackling heavy laundry loads or managing daily chores, the motor ensures that it delivers consistent performance. Apart from its strength, the noise reduction technology implemented in the design helps maintain a quieter environment during operation, addressing a common complaint from users of similar appliances.

In terms of design, the Sears 1700 boasts a sleek, modern aesthetic that integrates well into any household. With a user-friendly interface, it features intuitive controls, making it accessible to users of all ages. This commitment to user experience is reflected in the layout, with clearly labeled buttons and dials for ease of use.

Another significant aspect of the Sears 1700 is its versatility. It offers multiple settings tailored to different fabric types, ensuring optimal care and cleaning for garments. This adaptability makes it an essential appliance for families, allowing users to wash everything from delicate fabrics to heavy-duty items without compromising on quality.

The technology behind the Sears 1700 also includes energy-efficient settings, allowing users to save on utility bills while reducing their environmental footprint. This focus on sustainability is part of a broader trend in the appliance industry toward energy conservation, appealing to eco-conscious consumers.

Durability is another hallmark of the Sears 1700. Constructed with high-quality materials, it is designed to withstand the rigors of daily use. This reliability, combined with a warranty for peace of mind, has led many consumers to consider the Sears 1700 a long-term investment for their household needs.

In summary, the Sears 1700 stands out due to its powerful motor, noise reduction technology, user-friendly design, versatility, energy efficiency, and durability. These features collectively position it as a quality choice for consumers looking to enhance their home appliance lineup. Whether for laundry or other household tasks, the Sears 1700 has proven to be a dependable and efficient solution for many families.