Sears 153.329264 owner manual AIR in HOT Water Faucets

Page 24

D. An excess of active hydrogen in the tank. This is caused by corrosion protective action of the anode.

Smelly water may be eliminated or reduced in some water heater models by replacing the anode rod (s) with one of less active material, and then chlorinating the water heater tank and all hot water lines. Contact the local Sears Service Center for further information concerning an Anode Replacement Kit #9001453 and this Chlorination Treatment. Anode replacement and chlorination of the tank are not covered by the water heater’s limited warranty.

If the smelly water persists after the anode replacement and chlorination treatment; then you should consider chlorinating or aerating your water supply.

Do not remove the anode leaving the tank unprotected. By doing so, all warranty on the water heater tank is voided.

“AIR” IN HOT WATER FAUCETS

HYDROGEN GAS: Hydrogen gas can be produced in a hot water system that has not been used for a long period of time (generally two weeks or more). Hydrogen gas is extremely flammable and explosive. To prevent the possibility of injury under these conditions, we recommend the hot water faucet be opened for several minutes at the kitchen sink before any electrical appliances which are connected to the hot water system are used (such as a dishwasher or washing machine). If hydrogen gas is present, there will probably be an unusual sound similar to air escaping through the pipe as the hot water faucet is opened. There must be no smoking or open flame near the faucet at the time it is open.

RUMBLING NOISE

In some water areas, scale or mineral deposits will build up on your heating elements. This buildup will cause a rumbling noise. Follow “Element Cleaning/Replacement” instructions to clean and replace the elements.

HIGH TEMPERATURE SHUT OFF SYSTEM

The water heater has a high limit shut off system with a reset button located on the thermostat.

Follow the resetting instructions which refer to the high limit behind the access panel.

NOTE: If your water heater is connected to an “Off Peak” Clock, and uses the “3 wire lead” wiring diagram in the “Wiring Diagram” section, then the water heater will have a high limit on both the upper and lower thermostats. Follow the instructions to reset the high-limit behind the upper and lower access panels.

1.Before beginning, turn “OFF” electrical power supply to the water heater.

FIGURE 44.

2.Remove the two screws securing the access panel and remove panel.

3.Remove the insulation cap with handle.

4.Reset the high limit by pushing in the red button marked “RESET”.

FIGURE 45.

5.Replace the insulation cap with handle so that it completely covers the thermostat and element.

6.Replace the access panel.

7.Turn “ON” electric power to the water heater.

If the high limit must be reset again, call Sears Service Department to find out why the high limit turned “OFF” the electric power

NOT ENOUGH OR NO HOT WATER

1.In a new installation, the water heater may not be properly connected. Make sure the cold water supply valve is open. Review and check piping installation. Make sure that the cold water line is connected to the cold water inlet to the water heater and the hot water line to the hot water outlet on the water heater.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Power Miser Electric Water Heater Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.ASafe INSTALLATION, USE and Service General Safety Table of Contents Product Specifications IntroductionAdditional Tools Needed When Sweat Soldering Materials and Basic Tools NeededMaterials Needed Basic ToolsInstallation Instructions Removing the Old Water HeaterFacts to Consider About the Location Insulation BlanketsFacts to Consider About Convertible Lower Element Water Piping Temperature-Pressure Relief Valve Valve and Pipe InsulationFilling the Water Heater Converting the Lower Element Page Wiring Page Wiring Diagrams Service and Adjustment Temperature RegulationTemperature Settings Upper and Lower Thermostat AdjustmentsTemperature-Pressure Relief Valve Operation Anode Rod InspectionDraining Thermostat Removal/Replacement Element Cleaning/ReplacementPage Page Drain Valve Washer Replacement ServiceTroubleshooting Start Up ConditionsOperational Conditions AIR in HOT Water Faucets Water is TOO HOT Leakage Checkpoints Repair Parts List Model NumbersModelnumbers Repair Parts List Page Page MY-HOME

153.329264 specifications

Sears 153.329264 is an innovative and multi-functional piece of equipment that has gained significant attention in the retail and consumer market. Designed to cater to a variety of needs, this model boasts a range of features that enhance usability and functionality for both everyday consumers and professional users alike.

One of the main characteristics of the Sears 153.329264 is its robust build quality, ensuring reliability and longevity. Constructed with durable materials, it can withstand regular use and challenging environments. This makes it an ideal choice for both home and professional projects.

Incorporating advanced technologies, the Sears 153.329264 enhances operational efficiency and user experience. The equipment features a high-performance motor that provides superior power, making it suitable for a wide range of applications. This motor is designed for optimal energy consumption, maximizing performance while minimizing electricity usage.

Another notable feature is the user-friendly interface that simplifies operation, even for those who may not be highly experienced. The intuitive controls are clearly marked, allowing users to easily adjust settings according to their requirements. Additionally, the model is equipped with safety features that protect users during operation, such as automatic shut-off capabilities and thermal overload protection.

Versatility is a key selling point for the Sears 153.329264. It comes with a range of attachments and accessories, enabling users to customize the equipment for different tasks. Whether it’s for home improvement projects, crafting, or professional use in workshops, this model can adapt to various tasks with ease.

The compact design of the Sears 153.329264 allows for easy storage and portability. Its lightweight frame facilitates transport between job sites, making it a practical choice for professionals who are frequently on the move.

In conclusion, the Sears 153.329264 stands out as a top-tier device, combining durability, advanced technology, and versatility. Its user-centric design, combined with safety features and energy efficiency, makes it suitable for a broad audience, from DIY enthusiasts to seasoned professionals. This model embodies quality and performance, solidifying its place as a reliable choice in the market.
Top Page Image Contents