Bryant TSTATBBN2S01-C, TSTATBBNAC01-C instruction manual Check Thermostat Operation

Page 5

6.Use up and down buttons to select another Option, or press FAN button to exit configuration mode.

M.Option 19 — Equipment Present

This selection informs the thermostat of the heat, cool, and fan capabilities of the installed equipment. Select number 2, 3, or 4. Default is 4.

For equipment with both heat and cool capability and fan selection, choose 4.

For equipment with only heat or cool, but with fan selection, choose 3.

For equipment with only heat or cool and no fan selection, choose 2.

TO SELECT:

1.Enter configuration mode (if not already there).

2.Use up and down buttons to display Option 19. The SET icon should be off.

3.Press MODE button once. The SET icon will come on. The display now shows Option 19 setting.

4.Use up and down buttons to move between available Option 19 choices of 2 through 4. Factory default is 4.

5.Press MODE button again to return to Option 19. The SET icon will now be off.

6.Use up and down buttons to select another Option, or press FAN button to exit configuration mode.

N.Option 21 — Keypad Lockout

In OF (off) mode, the keypad is not locked out and has full functionality. In ON mode, the keypad is locked out and the lock icon on the display is illuminated. To unlock the keypad, the user must press and hold the up and down buttons simultaneously for approximately 5 seconds. The lock icon is turned off and the keypad will remain unlocked as long as the user presses a button at least every 30 seconds or for the entire duration of the installer test mode. If keypad remains idle for 30 seconds and the installer test mode is not in operation, the keypad will return to the locked state and the lock icon will illuminate on the screen.

TO SELECT:

1.Enter configuration mode (if not already there).

2.Use up and down buttons to display Option 21. The SET icon should be off.

3.Press MODE button once. The SET icon will come on. The display now shows Option 21 setting.

4.Use up and down buttons to move between available Option 21 choices of ON or OF. Factory default is OF.

5.Press MODE button again to return to Option 21. The SET icon will now be off.

6.Use up and down buttons to select another Option, or press FAN button to exit configuration mode.

O.Installer Test Mode

Installer test will be initiated by pressing the fan button for 20 seconds (15 seconds will enter installer setup. InS will appear on the screen and the SERVICE icon will be illuminated.

In installer test mode, pressing the MODE button will change the system operating mode. Note that AUTO mode is not available in installer test. Heating and cooling modes must be tested indepen- dently.

a.If the mode is set to HEAT, the first stage of heating will be energized for three minutes (180 seconds), and then the first and second stages (if a second stage exists) will turn on for an additional three minutes. Installer test will always attempt to run a second stage output whether it is attached or not, providing a minimum of 6 minutes of first stage operation. At the end of the 6 minute period, the MODE will return to OFF.

b.Pressing the FAN button while the heating or cooling equipment is not running will turn on the FAN relay and display the FAN icon.

c.If the mode is set to COOL, the first stage of cooling turns on for three minutes, then first and second stages (if a second stage exists) will turn on for three minutes.

d.If the mode is set to EHEAT, auxiliary heat turns on for three minutes, then the mode returns to OFF.

Terminating Installer Test

After 15 minutes of inactivity (no button presses by the installer), thermostat will automatically revert to normal operation. Pressing RESET FILTER any time during installer test will terminate installer test and return the thermostat to normal operation.

V. CHECK THERMOSTAT OPERATION

A.Fan Operation

1.Press FAN button, starting continuous fan operation. FAN icon turns on.

2.Press FAN button again, stopping fan operation. FAN icon turns off. (Some fan coils have 90 sec fan off delay, so fan may not stop immediately.)

B.Outdoor Temperature Sensor

If system is equipped with an outdoor temperature sensor, check its operation by pressing both, the temperature UP and DOWN buttons simultaneously. Outdoor temperature will be displayed for about 5 sec. If ″--″is displayed, the outdoor temperature sensor is absent or not properly connected.

C.Checklist

1.Run equipment through several heating and cooling cycles to ensure proper operation.

2.If equipment is to be left in operation, set point and operating mode must be properly selected.

3.Put away tools and instruments, and clean up debris.

4.Review Homeowner’s Guide with owner.

5.Leave literature packet with owner.

—5—

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Installation Considerations Safety ConsiderationsInstallation Thermostat Location IntroductionIII. Install Thermostat Model Selection and Wiring Diagram ChartIV. SET Thermostat Configuration Option 01-Anticipator AdjustmentOption 05 HP and 2S / AC Configuration Option 02-Clean Filter TimerOption 07-Zoning On/Off Configuration Option 03-Fahrenheit/Celsius SelectionOption 15-Auto Mode On/Off Selection Option 13-Room Temperature OffsetOption 18 Backlight Configuration Option 08-High Ambient Auxiliary Heat LockoutCheck Thermostat Operation Single-Speed Air Conditioner With Typical Fan Coil NON-PROGRAMMABLE -C Thermostat Quick ReferenceA98455 See notes 2, 4, 6, 10Model 2S 01-C W2/BA98463 See note 10See notes 5, 6, 7, 8, 10 , A04011A98466 A04012See notes 7 , 10 and 1 A04013Wiring Diagram Notes Operational Information Thermostat TroubleshootingA04105 NON-PROGRAMMABLE Thermostat Configuration Record

TSTATBBN2S01-C, TSTATBBNAC01-C specifications

The Bryant TSTATBBNAC01-C and TSTATBBN2S01-C are advanced thermostats designed to enhance comfort and energy efficiency in residential and commercial settings. These models stand out for their user-friendly interfaces and a plethora of features aimed at providing precise temperature control and convenience.

One of the main features of both models is their smart programming capability. They allow homeowners to set schedules that adjust heating and cooling according to daily routines. This can lead to significant energy savings, as the systems can optimize temperature settings during periods when a home is unoccupied. Both thermostats are compatible with multi-stage heating and cooling applications, including traditional HVAC systems and heat pumps, making them versatile choices for various climate control setups.

The TSTATBBNAC01-C and their counterpart, the TSTATBBN2S01-C, utilize advanced technology that enables remote access. Users can control their home environment through mobile apps, providing the flexibility to modify settings on the go. This feature is particularly useful for those who want to return to a comfortable home after being away for an extended period.

In terms of compatibility, both thermostats support integration with leading HVAC systems, ensuring a seamless setup for users. They are designed to work with both gas and electric systems, enhancing their functionality across different heating and cooling environments. The connection capabilities extend to Wi-Fi networks, allowing real-time updates and software upgrades that improve performance over time.

The sleek, modern design of the TSTATBBNAC01-C and TSTATBBN2S01-C makes them aesthetically pleasing and easy to read. They feature intuitive touchscreens that display temperature, humidity levels, and other critical information at a glance. This clarity aids users in making informed decisions about their heating and cooling needs.

Energy efficiency is a cornerstone of both thermostat models. By integrating features such as auto-optimization and energy use history, they empower users to reduce their energy consumption. This not only leads to lower utility bills but also contributes to a more sustainable lifestyle.

Overall, the Bryant TSTATBBNAC01-C and TSTATBBN2S01-C thermostats epitomize the modern home’s need for comfort and efficiency. With their advanced programming, remote access capabilities, and sleek designs, they are a worthy investment for anyone looking to enhance their living or working environment.
Top Page Image Contents