BEA 80.0240.04 manual Cup, Master Slave

LO-LINX	BLACK	BLACK	24 V	RED
Patent Pending
	RED	BLACK	TRANSFORMER	RED

			MTR	STALL	SENSORS	AUX
						BEAM	SWITCH TO CTRL	PWR	SETUP
						TX RX					ON
										RED
											Pre-wired
										BLACK	OFF switch
										WHITE	assembly
		LO-LINX MOTOR HARNESS									HOLD OPEN
		p/n: 70.5076
			SEE NOTE #2							LO-LINX POWER HARNESS p/n: 70.5095
		SEE NOTE #1								LO-LINX HOLD SWITCH HARNESS p/n: 70.5078
MOTOR	+ RED
	-	RED								LO-LINX CONTROL HARNESS p/n: 70.5097
							SEE NOTE #3
											SEE NOTE #5
							N/O
							COM			BROWN
										SEE NOTE #4
EAGLE 1		BODYGUARD 1							BODYGUARD 2	EAGLE 2
						LO-LINX BODYGUARD				BLUE
						DUAL-EGRESS HARNESS				WHITE
						p/n: 20.5083
										GREEN
			LO-LINX							YELLOW
			BODYGUARD								SYNC CABLE
			HARNESS
			p/n: 70.5082							CUP	CUP
		LO-LINX EAGLE HARNESS p/n: 70.5096
										MASTER	SLAVE
		LO-LINX SUPERSCAN HARNESS						LO-LINX SUPERSCAN HARNESS
		p/n: 70.5071							p/n: 70.5071

DOOR MTD SENSOR	DOOR MTD SENSOR	DOOR MTD SENSOR	DOOR MTD SENSOR
APPROACH SIDE	SAFETY SIDE	APPROACH SIDE	SAFETY SIDE

NOTES:

1.MOTOR CONNECTION IS TIED IN PARALLEL TO EXISTING MOTOR LEADS. NO RESPECT TO POLERITY IS REQUIRED.

2.LEAVE THE FACTORY INSTALLED JUMPERS IN PLACE.

3.THE KNOWING ACT SWITCH IS CONNECTED AT THE AUX INPUT AND CAN BE ANY DRY CONTACT DEVICE SUCH AS A PUSHPLATE, CARD READER, ETC. THE AUX INPUT IS REQUIRED FOR ALL INITIAL ACTIVATION WHEN FUNCTION FA ON THE LO-LINX IS SET TO '01'.

4.THE SECOND BODYGUARD AND EAGLE ARE PRIMARILY USED IN DUAL-EGRESS APPLICATIONS. IF A SECOND BODYGUARD IS REQUIRED, USE A "Y" HARNESS (20.5083).

5.SET CONTROL FUNTIONS WITH PMD 20 = A, 11 = DEGREE AT WHICH TO INHIBIT SUPERSCAN DEPENDING ON APPLICATION 65-75 DEGREES TYPICALY; 17 = 00; 18 = 00

IF AFTER TROUBLESHOOTING A PROBLEM, A SATISFACTORY SOLUTION CANNOT BE ACHIEVED, PLEASE CALL B.E.A., INC. FOR FURTHER ASSISTANCE DURING EASTERN STANDARD TIME @ 1-800-523-2462 FROM 8AM - 5PM. FOR AFTER-HOURS, CALL EAST COAST: 1-866-836-1863 OR 1-800-407-4545 / MID-WEST: 1-888-308-8843 /

WEST COAST:1-888-419-2564. DO NOT LEAVE ANY PROBLEM UNRESOLVED. IF YOU MUST WAIT FOR THE FOLLOWING WORKDAY TO CALL B.E.A., LEAVE THE DOOR INOPERABLE UNTIL SATISFACTORY REPAIRS CAN BE MADE. NEVER SACRIFICE THE SAFE OPERATION OF THE AUTOMATIC DOOR OR GATE FOR AN INCOMPLETE SOLUTION.WEB: WWW.BEASENSORS.COM

100 ENTERPRISE DRIVE PITTSBURGH, PA 15275 PHONE: (412) 249-4100 FAX: (412) 249-4101 EMAIL: www.beasensors.com

TITLE: BESAM CUP/MP W/LO-LINX

	DRAWN BY:	REV BY:	PART NO:
SIZE:			80.0245.03
	TUC	TUC
B	SCALE:	DATE:	SHEET
	NONE	05/17/2007	1 OF 1