AVEC VOTRE
OPERATING INSTRUCTIONS
Post-Motor Filter
The post motor filter is located on the top of the vacuum.
1.Lift the locking tab of the post motor cover remove the cover. (Fig 15)
2.Remove the post motor filter located inside the cover.
3.Wash the post motor filter in lukewarm water. A mild detergent may be used if required. (Fig. 16)
4.Let the post motor filter air dry completely before replacing into the vacuum.
Important: Do not use a washing machine to wash the filter. Do not use a hair dryer to dry. Air dry only.
Fig. 15
Fig. 16
1. | Bouton d’alimentation On/Off | 16. Réceptacle du tube télescopique |
2. | Couvercle de filtre d’échappement | 17. Tube télescopique |
3. | Bouton rétracteur de cordon | 18. Fiche du tube télescopique |
4. | Commande de succion variable | 19. Collier de réglage du tube |
5. | Compartiment à outils | télescopique |
6. | Entrée d’air | 20. Bouton de relâche de la poignée du |
7. | Réceptacle du cordon d'alimentation | tube |
8. | Poignée de transport | 21. Fiche du tube télescopique |
9. | Bouton de relâche du sac à poussière | 22. Réceptacle du bec électrique |
10. | Témoin de sac à poussière plein | 23. Bouton de relâche du tube |
11. | Cordon d’alimentation | télescopique |
12. | Boyau souple | 24. Sélecteur de hauteur de tapis |
13. | Poignée du boyau souple | 25. Témoin du bec électrique |
14. | Bouton On/Off du bec électrique | 26. Suceur plat |
15. | Commande de succion manuelle | 27. Brosse à épousseter |
|
| 28. Brosse à meubles |
|
| 29. Sacs à poussière HEPA (4) |
*Les illustrations peuvent différer du produit
Spécifications Techniques
Tension: | 120 V, 60 Hz |
Intensité: | 12 A |
TROUBLE SHOOTING GUIDE
TROUBLESHOOTING GUIDE
PROBLEM |
| POSSIBLE REASON | POSSIBLE SOLUTION | ||
|
|
| 1. | Check for blockage - | |
| 1. | Hose, wand or inlet is |
| remove it. | |
Motor runs but no |
| blocked. | 2. | HEPA dust bag is full, | |
2. | Check bag full indicator. |
| replace HEPA dust bag. | ||
suction |
| ||||
3. | Hose clamp not assembled | 3. | Insert hose clamp into hose | ||
|
| to hose inlet properly. |
| inlet until "snap" locks for | |
|
|
|
| proper assembly. | |
|
|
|
|
| |
|
|
| 1. | Pull cord out, straighten | |
Cord does not | 1. | Cord twisted. |
| and rewind again. | |
2. | Cord pulled out too far - | 2. | Holding the plug, press the | ||
rewind | |||||
| beyond "RED" mark. |
| rewind button and try to | ||
|
|
|
| rewind again. | |
|
|
|
|
| |
|
|
| 1. | Plug unit in firmly. | |
| 1. | Not firmly plugged in. | 2. | Check fuse or breaker. | |
| 3. | Replace fuse/reset | |||
| 2. | No electricity in wall outlet. | |||
Vacuum won't run |
| breaker. | |||
3. | Blown fuse/tripped breaker. |
| |||
4. | Turn vacuum off and | ||||
| 4. | Motor thermostat may have | |||
|
| unplug from outlet. Allow | |||
|
| tripped. |
| ||
|
|
| unit to cool down before | ||
|
|
|
| ||
|
|
|
| trying to switch "ON" again. | |
|
|
|
|
|
23 | 8 |