State Industries 100, 101 warranty BELOW. Keep Clear of ALL Obstructions

Page 7

INSTALLATION REQUIREMENTS FOR THE COMMONWEALTH OF MASSACHUSETTS

For all side wall terminated, horizontally vented power vent, direct vent, and power direct vent gas fueled water heaters installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied:

INSTALLATION OF CARBON MONOXIDE DETECTORS At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the sidewall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors.

In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.

In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days to comply with the above requirements provided that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm shall be installed.

APPROVED CARBON MONOXIDE DETECTORS Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/UL 2034 listed and CSA certified.

SIGNAGE A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print size no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY

BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS.”

INSPECTION The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a) 1 through 4.

EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:

1.The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the Board; and

2.Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building, or structure used in whole or in part for residential purposes.

MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment and the venting system shall include:

1.Detailed instructions for the installation of the venting system design or the venting system components; and

2.A complete parts list for the venting system design or venting system.

MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies “special venting systems,” the following requirements shall be satisfied by the manufacturer:

1.The referenced “special venting system” instructions shall be included with the appliance or equipment installation instructions; and

2.The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed installation instructions.

A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Printed Ultra Force SUF 60 120 Thru SUF 100Temperature Rise Degrees F Gallons PER Hour Ultra Force SUF 120 250A ROUGH-IN-DIMENSIONSForeword Features Table of ContentsInstallation Instructions Clearances Locating the HeaterUnconfined Space Hard WaterAIR Requirements Mechanical Exhausting of Room AIRBELOW. Keep Clear of ALL Obstructions Canadian Power Vent Power VentCanadian Direct Vent Direct VentInstallation Sequence Direct Vent Terminal InstallationDirect Venting Vertical Vent Terminal Installation Selection of Materials Installation of Vent SystemVent Pipe Preparation Initial PreparationGAS Piping Controls and SwitchesAttaching gas supply pipe to gas valve inlet Connection of GAS PipeSystem Connections Heater Wiring Overview Using the Electronic ControllerOperating States Changing the Display Units Prior to Start UP Viewing the Fault HistoryOperating Instructions Adjustment ProcedureGeneral Information MaintenanceFor Your Safety Read Before Operating Models only 199/250 Models only Sediment Removal Powered Anode SystemFlushing DrainingVent System Drain Valve and Access PanelsInstallation Diagrams Page Must be Identical Heaters Pipe Relief Valve to Open Drain Page Manifold Kits TROUBLE-SHOOTING Checklist and Service InformationGAS Fails to Shut OFF Replacement PartsMotor will not RUN Motor RUNS, Burner Lights Momentarily Then Locks OUTModel SUF Limited Warranty Page Page Page Tennessee Waltz Parkway Ashland CITY, TN

100, 101 specifications

State Industries 101,100 is an innovative company that specializes in manufacturing high-quality industrial equipment and machinery. Founded with a vision to enhance productivity and efficiency across various sectors, State Industries has established itself as a trusted name in the industry. The company is known for its commitment to quality, sustainability, and cutting-edge technology, making it a preferred choice for businesses looking to elevate their operations.

One of the main features of State Industries 101,100 is its extensive product line, which includes a wide range of industrial machines, tools, and systems. The company’s offerings are designed to cater to various industries, such as manufacturing, construction, energy, and transportation. From heavy-duty machinery to precision tools, State Industries ensures that its products meet the highest standards of performance and reliability.

A key aspect of State Industries’ success is its incorporation of advanced technologies in its manufacturing processes. The company utilizes state-of-the-art machinery and techniques, including computer-aided design (CAD), robotics, and automation. These technologies enable State Industries to produce parts and equipment with exceptional precision, which ultimately leads to improved overall performance. Additionally, the company places a strong emphasis on research and development, constantly seeking new ways to innovate and enhance its product offerings.

Sustainability is another defining characteristic of State Industries 101,100. The company is deeply committed to minimizing its environmental impact by adopting eco-friendly practices throughout its operations. This includes using sustainable materials, reducing waste during production, and implementing energy-efficient technologies. State Industries also actively engages in initiatives aimed at promoting green technology, striving to contribute positively to the environment while delivering high-quality industrial solutions.

Customer satisfaction remains a top priority for State Industries. The company fosters strong relationships with its clients by offering tailored solutions, responsive customer service, and comprehensive support throughout the product lifecycle. With a focus on understanding customer needs and challenges, State Industries is dedicated to delivering exceptional value and reliability with every product.

In summary, State Industries 101,100 stands out as a forward-thinking company that combines advanced technology, a commitment to sustainability, and a customer-centric approach in its operations. As industries evolve and face new challenges, State Industries is well-positioned to continue leading the way in industrial innovation.
Top Page Image Contents