State Industries 100, 101 warranty Vertical Vent Terminal Installation

Page 11

5.Glue the intake vent terminal to the section of the pipe.

6.Slide the wall plate over the pipe to stop against intake vent terminal.

7.Place a bead of caulking (not supplied) around the gap between the pipe and the wall. Place some of the caulking on the back of the plate to hold it against the wall after installation.

8.If the vent pipe is installed up to the wall, with a coupling on the end against the wall opening, the pipe with the vent terminal can be prepared for gluing before inserting through the wall. Slide the pipe through the wall and insert into coupling on the other side of the wall, making sure that the vent terminal ends up pointed in the correct position (See Figure 9).

FIGURE 9.

FIGURE 10.

VERTICAL VENT TERMINAL INSTALLATION

IMPORTANT

WHEN TERMINATING THROUGH A ROOF, THE FOLLOWING

SPECIFICATIONS PERTAINING TO TERMINAL LOCATION MUST BE FOLLOWED.

1.Proper support must be provided for all pipe protruding through the roof.

2.The vertical roof terminations should be sealed with a plumbing roof boot or equivalent flashing.

3.The intake vent termination and the exhaust vent termination must penetrate the same side of roof.

4.The center line of the intake vent termination and the center line of the exhaust vent termination must be no closer than 24" (61cm).

5.The intake vent terminal and the exhaust vent terminal must be oriented facing downward and the same direction.

The specifications are displayed in Figure 10 & 11.

NOTE: Exhaust vent terminal is installed using the same procedure.

INSTALLATION SEQUENCE

NOTE: BEFORE BEGINNING INSTALLATION OF ANY VENT PIPE, READ “VENT PIPE PREPARATION” SECTION ON PAGE 12.

1.After the points of termination have been determined, use the cover plates as templates to mark the holes for the vent pipes to be inserted through the roof.

2.Drill a pilot hole approximately 1/4" (6 mm) outside of the marked circle. This pilot hole is used as a starting point for a saws-all or sabre saw blade. Cut around the marked circle staying approximately one quarter inch outside the line. (This will allow the vent pipe to easily slide through the opening). The resulting gap will be covered by the roof boot/flashing.

3.Suspend the pipe through the center of the hole using proper support.

4.Slide roof boot or equivalent flashing over pipe and secure roof boot equivalent flashing to roof.

5.Seal around flashing.

6.Terminate intake terminal and exhaust vent terminal facing down as shown in Figure 11.

FIGURE 11.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Printed Ultra Force SUF 60 120 Thru SUF 100Foreword Ultra Force SUF 120 250A ROUGH-IN-DIMENSIONSTemperature Rise Degrees F Gallons PER Hour Features Table of ContentsInstallation Instructions Clearances Locating the HeaterUnconfined Space Hard WaterAIR Requirements Mechanical Exhausting of Room AIRBELOW. Keep Clear of ALL Obstructions Canadian Power Vent Power VentCanadian Direct Vent Direct VentDirect Venting Direct Vent Terminal InstallationInstallation Sequence Vertical Vent Terminal Installation Selection of Materials Installation of Vent SystemVent Pipe Preparation Initial PreparationGAS Piping Controls and SwitchesAttaching gas supply pipe to gas valve inlet Connection of GAS PipeSystem Connections Heater Wiring Overview Using the Electronic ControllerOperating States Changing the Display Units Prior to Start UP Viewing the Fault HistoryOperating Instructions Adjustment ProcedureGeneral Information MaintenanceFor Your Safety Read Before Operating Models only 199/250 Models only Sediment Removal Powered Anode SystemFlushing DrainingVent System Drain Valve and Access PanelsInstallation Diagrams Page Must be Identical Heaters Pipe Relief Valve to Open Drain Page Manifold Kits TROUBLE-SHOOTING Checklist and Service InformationGAS Fails to Shut OFF Replacement PartsMotor will not RUN Motor RUNS, Burner Lights Momentarily Then Locks OUTModel SUF Limited Warranty Page Page Page Tennessee Waltz Parkway Ashland CITY, TN

100, 101 specifications

State Industries 101,100 is an innovative company that specializes in manufacturing high-quality industrial equipment and machinery. Founded with a vision to enhance productivity and efficiency across various sectors, State Industries has established itself as a trusted name in the industry. The company is known for its commitment to quality, sustainability, and cutting-edge technology, making it a preferred choice for businesses looking to elevate their operations.

One of the main features of State Industries 101,100 is its extensive product line, which includes a wide range of industrial machines, tools, and systems. The company’s offerings are designed to cater to various industries, such as manufacturing, construction, energy, and transportation. From heavy-duty machinery to precision tools, State Industries ensures that its products meet the highest standards of performance and reliability.

A key aspect of State Industries’ success is its incorporation of advanced technologies in its manufacturing processes. The company utilizes state-of-the-art machinery and techniques, including computer-aided design (CAD), robotics, and automation. These technologies enable State Industries to produce parts and equipment with exceptional precision, which ultimately leads to improved overall performance. Additionally, the company places a strong emphasis on research and development, constantly seeking new ways to innovate and enhance its product offerings.

Sustainability is another defining characteristic of State Industries 101,100. The company is deeply committed to minimizing its environmental impact by adopting eco-friendly practices throughout its operations. This includes using sustainable materials, reducing waste during production, and implementing energy-efficient technologies. State Industries also actively engages in initiatives aimed at promoting green technology, striving to contribute positively to the environment while delivering high-quality industrial solutions.

Customer satisfaction remains a top priority for State Industries. The company fosters strong relationships with its clients by offering tailored solutions, responsive customer service, and comprehensive support throughout the product lifecycle. With a focus on understanding customer needs and challenges, State Industries is dedicated to delivering exceptional value and reliability with every product.

In summary, State Industries 101,100 stands out as a forward-thinking company that combines advanced technology, a commitment to sustainability, and a customer-centric approach in its operations. As industries evolve and face new challenges, State Industries is well-positioned to continue leading the way in industrial innovation.
Top Page Image Contents