State Industries 184748-001 instruction manual

Page 17

The water passing out of the drain valve may be extremely hot. To avoid scalding, make sure all connections are tight and that the water flow is directed away from any person.

4.Remove the two screws securing the outer door, and remove door.

FIGURE 15.

5.Remove the insulation block and pad.

FIGURE 16.

6.A. Models with lower thermostat without high limit: Lift out the tab as shown below to unclip the terminal cover from the thermostat. The terminal cover can now be removed from the thermostat.

B.Models with Upper or Lower Thermostat with High Limit: Lift out the tab as shown below to unclip the terminal cover from the thermostat. The terminal cover can now be removed from the thermostat.

FIGURE 18.

7.Disconnect the two wires on the element and unscrew the old element from the tank.

FIGURE 19.

8.Clean the area around the element opening. Remove any sediment from or around the element opening and inside the tank.

9.If you are cleaning the element you have removed, do so by scraping or soaking in vinegar or a deliming solution.

NOTE: Replacement elements must (1) be the same voltage and (2) no greater wattage than listed on the model rating plate affixed to the water heater.

10.A new gasket should be used in all cases to prevent a possible water leak. Place the new element gasket on the threaded side of the cleaned or new element and screw into tank, securing tightly using an element wrench.

FIGURE 17.

FIGURE 20.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Residential HUD Side Plumbing Electric Important Definitions Safe INSTALLATION, USE and ServiceGeneral Safety Introduction Table of ContentsTypical Installation Facts to Consider about the Location Mixing Valve UsageLocating the NEW Water Heater Water Piping Installing the NEW Water HeaterInsulation Blankets Water Piping Pressure Test TEMPERATURE-PRESSURE Relief ValveFilling the Water Heater Valve and Pipe Insulation On Selected Models Wiring Diagrams Wiring Temperatureadjustment Temperature RegulationOperational Conditions For Your InformationTEMPERATURE-PRESSURE Relief Valve Operation Periodic MaintenanceThermostat Removal / Replacement Anode ROD InspectionElement Cleaning / Replacement Page Service Drain Valve Washer ReplacementLeakage Checkpoints Problem Cause Solution Troubleshooting GuidelinesManufactured Mobile Home Electric Models Repair Parts ListPage

184748-001 specifications

State Industries 184748-001 is a prominent water heater model that exemplifies advanced engineering and efficiency in residential and commercial applications. With a focus on reliability and energy savings, it is designed to meet the diverse needs of users while ensuring optimal performance.

One of the main features of the 184748-001 is its innovative insulation system. The water heater is equipped with high-density foam insulation that minimizes heat loss, which not only improves energy efficiency but also reduces operating costs. This feature makes it a suitable choice for those looking to lower their utility bills while still enjoying a consistent supply of hot water.

The 184748-001 utilizes a robust heating element that guarantees rapid recovery rates, ensuring that hot water is always available when needed. This model houses a powerful electric heating element that is designed for longevity and efficient operation. As a result, even during peak usage times, users can expect to have a steady flow of hot water, making it ideal for households with high demand or commercial applications.

In terms of capacity, the model can accommodate various needs, featuring a range of tank sizes to suit different households and facilities. Whether you're outfitting a large family home or a small business, the versatility of the 184748-001 allows it to adapt to a multitude of settings, ensuring that it meets the specific demands of each environment.

Another characteristic of this water heater is its user-friendly digital control panel. This feature allows for precise temperature adjustments, making it convenient for users to customize their hot water experience according to personal preferences. The digital interface also includes energy monitoring capabilities, providing insights into consumption patterns that help users make informed decisions regarding their energy usage.

Furthermore, State Industries has prioritized safety in the design of the 184748-001. Equipped with multiple safety features such as temperature and pressure relief valves, this model ensures that the system operates within safe parameters, reducing the risk of accidents and enhancing user confidence.

In summary, the State Industries 184748-001 water heater stands out for its combination of energy efficiency, robust performance, and user-friendly technologies. With its focus on safety and adaptability, it represents a smart investment for those seeking reliable hot water solutions for their homes or businesses.
Top Page Image Contents