Installing the NEW Water Heater

LOCATING THE NEW WATER HEATER

Installation of the water heater must be accomplished in such a manner that if the tank or any connections should leak, the flow will not cause damage to the structure. For this reason, it is not advisable to install the water heater in an attic or upper floor. When such locations cannot be avoided, a suitable drain pan should be installed under the water heater. Drain pans are available from your local plumbing contractor. Such a drain pan must have a minimum length and width of at least 2 inches (51 mm) greater that the water heater dimensions and must be piped to an adequate drain.

Water heater life depends upon water quality, water pressure and the environment in which the water heater is installed. Water heaters are sometimes installed in locations where leakage may result in property damage, even with the use of a drain pan piped to a drain. However, unanticipated damage can be reduced or prevented by a leak detector or water shut-off device used in conjunction with a piped drain pan. These devices are available from some plumbing supply wholesalers and retailers, and detect and react to leakage in various ways:

•Sensors mounted in the drain pan that trigger an alarm or turn off the incoming water to the water heater when leakage is detected.

•Sensors mounted in the drain pan that turn off the water supply to the entire home when water is detected in the drain pan.

•Water supply shut-off devices that activate based on the water pressure differential between the cold water and hot water pipes connected to the water heater.

•Devices that will turn off the gas supply to a gas water heater while at the same time shutting off its water supply.

Also, the water heater must be located and/or protected so it is not subject to physical damage by a moving vehicle.

INSULATION BLANKETS

Insulation blankets are available to the general public for external use on electric water heaters but are not necessary with this product. The purpose of an insulation blanket is to reduce the standby heat loss encountered with storage tank heaters. Your water heater meets or exceeds the National Appliance Energy Conversation Act standards with respect to insulation and standby loss requirements, making an insulation blanket unnecessary.

Should you choose to apply an insulation blanket to this heater, you should follow these instructions below. Failure to follow these instructions can result in fire, serious personal injury, or death.

•Do not cover the temperature and pressure relief (T & P) valve with an insulation blanket.

•Do not cover the instruction manual. Keep it on the side of the water heater or nearby for future reference.

•Do obtain new warning and instruction labels for placement on the blanket directly over the existing labels.

WATER PIPING

HOTTER WATER CAN SCALD:

Water heaters are intended to produce hot water. Water heated to a temperature which will satisfy space heating, clothes washing, dish washing, cleaning and other sanitizing needs can scald and permanently injure you upon contact. Some people are more likely to be permanently injured by hot water than others. These include the elderly, children, the infirm, or physically/mentally handicapped. If anyone using hot water in your home fits into one of these groups or if there is a local code or state law requiring a certain temperature water at the hot water tap, then you must take special precautions. In addition to using the lowest possible temperature setting that satisfies your hot water needs, a means such as a *mixing valve, shall be used at the hot water

taps used by these people or at the water heater. Valves for reducing point of use temperature by mixing cold and hot water are also available.

Consult a Qualified Installer or ServiceAgency. Follow manufacturer’s instructions for installation of the valves. Before changing the factory setting on the thermostat, read the “Temperature Regulation” section in this manual.

This water heater shall not be connected to any heating systems or component(s) used with a non-potable water heating appliance.

Toxic chemicals, such as those used for boiler treatment shall not be introduced into this system.

Water supply systems may, because of such events as high line pressure, frequent cut-offs, the effects of water hammer among others, have installed devices such as pressure reducing valves, check valves, back flow preventers, etc. to control these types of problems. When these devices are not equipped with an internal by-pass, and no other measures are taken, the devices cause the water system to be closed. As water is heated, it expands (thermal expansion) and closed systems do not allow for the expansion of heated water.

184748-001 specifications

State Industries 184748-001 is a prominent water heater model that exemplifies advanced engineering and efficiency in residential and commercial applications. With a focus on reliability and energy savings, it is designed to meet the diverse needs of users while ensuring optimal performance.

One of the main features of the 184748-001 is its innovative insulation system. The water heater is equipped with high-density foam insulation that minimizes heat loss, which not only improves energy efficiency but also reduces operating costs. This feature makes it a suitable choice for those looking to lower their utility bills while still enjoying a consistent supply of hot water.

The 184748-001 utilizes a robust heating element that guarantees rapid recovery rates, ensuring that hot water is always available when needed. This model houses a powerful electric heating element that is designed for longevity and efficient operation. As a result, even during peak usage times, users can expect to have a steady flow of hot water, making it ideal for households with high demand or commercial applications.

In terms of capacity, the model can accommodate various needs, featuring a range of tank sizes to suit different households and facilities. Whether you're outfitting a large family home or a small business, the versatility of the 184748-001 allows it to adapt to a multitude of settings, ensuring that it meets the specific demands of each environment.

Another characteristic of this water heater is its user-friendly digital control panel. This feature allows for precise temperature adjustments, making it convenient for users to customize their hot water experience according to personal preferences. The digital interface also includes energy monitoring capabilities, providing insights into consumption patterns that help users make informed decisions regarding their energy usage.

Furthermore, State Industries has prioritized safety in the design of the 184748-001. Equipped with multiple safety features such as temperature and pressure relief valves, this model ensures that the system operates within safe parameters, reducing the risk of accidents and enhancing user confidence.

In summary, the State Industries 184748-001 water heater stands out for its combination of energy efficiency, robust performance, and user-friendly technologies. With its focus on safety and adaptability, it represents a smart investment for those seeking reliable hot water solutions for their homes or businesses.