State Industries 184748-001 instruction manual Element Cleaning / Replacement

Page 16

1.Turn “OFF” the electric power supply to the water heater.

2.Remove the outer door, insulation block and pad in the order they are installed.

3.A. Models with lower thermostat without high limit: Lift out the tab as shown below to unclip the terminal cover from the thermostat. The terminal cover can now be removed from the thermostat.

FIGURE 11.

B.Models with Upper or Lower Thermostat with High Limit: Lift out the tab as shown below to unclip the terminal cover from the thermostat. The terminal cover can now be removed from the thermostat.

FIGURE 12.

4.Remove the two wires attached to the thermostat.

5.Remove the thermostat from behind the thermostat bracket.

6.Disconnect wires from thermostat and slide out of the bracket.

7.Place the new lower thermostat in the bracket making sure it fits firmly against the tank.

8.Attach the wires to the new thermostat.

NOTE: Some of the terminals may require straight-in wiring through an eye-opening. If wires are now looped, recut and strip wire 3/8” to a straight length and insert.

9.Put plastic terminal cover back in place.

10.Replace the insulation block and pad to cover the thermostat.

11.Replace outer door then turn the electric power “ON”.

ELEMENT CLEANING / REPLACEMENT

NOTE: These instructions are written for element cleaning and element replacement for the lower element.

To remove the element from the tank in order to clean or replace it:

1.Before beginning turn “OFF” the electric power supply to the water heater.

2.Turn off the water supply to the water heater at the water shut-off valve or water meter.

FIGURE 13.

3.Attach a hose to the water heater drain valve and put the other end in a floor drain or outdoors. Open the water heater drain valve. Open a nearby hot water faucet which will relieve pressure in the water heater and speed draining.

FIGURE 14.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Residential HUD Side Plumbing Electric Safe INSTALLATION, USE and Service Important DefinitionsGeneral Safety Table of Contents IntroductionTypical Installation Locating the NEW Water Heater Mixing Valve UsageFacts to Consider about the Location Insulation Blankets Installing the NEW Water HeaterWater Piping TEMPERATURE-PRESSURE Relief Valve Water Piping Pressure TestFilling the Water Heater Valve and Pipe Insulation On Selected Models Wiring Diagrams Wiring Temperature Regulation TemperatureadjustmentFor Your Information Operational ConditionsPeriodic Maintenance TEMPERATURE-PRESSURE Relief Valve OperationThermostat Removal / Replacement Anode ROD InspectionElement Cleaning / Replacement Page Drain Valve Washer Replacement ServiceLeakage Checkpoints Troubleshooting Guidelines Problem Cause SolutionRepair Parts List Manufactured Mobile Home Electric ModelsPage

184748-001 specifications

State Industries 184748-001 is a prominent water heater model that exemplifies advanced engineering and efficiency in residential and commercial applications. With a focus on reliability and energy savings, it is designed to meet the diverse needs of users while ensuring optimal performance.

One of the main features of the 184748-001 is its innovative insulation system. The water heater is equipped with high-density foam insulation that minimizes heat loss, which not only improves energy efficiency but also reduces operating costs. This feature makes it a suitable choice for those looking to lower their utility bills while still enjoying a consistent supply of hot water.

The 184748-001 utilizes a robust heating element that guarantees rapid recovery rates, ensuring that hot water is always available when needed. This model houses a powerful electric heating element that is designed for longevity and efficient operation. As a result, even during peak usage times, users can expect to have a steady flow of hot water, making it ideal for households with high demand or commercial applications.

In terms of capacity, the model can accommodate various needs, featuring a range of tank sizes to suit different households and facilities. Whether you're outfitting a large family home or a small business, the versatility of the 184748-001 allows it to adapt to a multitude of settings, ensuring that it meets the specific demands of each environment.

Another characteristic of this water heater is its user-friendly digital control panel. This feature allows for precise temperature adjustments, making it convenient for users to customize their hot water experience according to personal preferences. The digital interface also includes energy monitoring capabilities, providing insights into consumption patterns that help users make informed decisions regarding their energy usage.

Furthermore, State Industries has prioritized safety in the design of the 184748-001. Equipped with multiple safety features such as temperature and pressure relief valves, this model ensures that the system operates within safe parameters, reducing the risk of accidents and enhancing user confidence.

In summary, the State Industries 184748-001 water heater stands out for its combination of energy efficiency, robust performance, and user-friendly technologies. With its focus on safety and adaptability, it represents a smart investment for those seeking reliable hot water solutions for their homes or businesses.
Top Page Image Contents