State Industries 184748-001 instruction manual Mixing Valve Usage, Locating the NEW Water Heater

Page 6

MIXING VALVE USAGE

FIGURE 2.

Water (Potable) Heating: All models are considered suitable for

HOTTERWATERCANSCALD:

water (potable) heating only.

Water heaters are intended to produce hot water. Water heated to a

 

 

temperature which will satisfy space heating, clothes washing, dish

 

washing, and other sanitizing needs can scald and permanently injure

 

you upon contact. Some people are more likely to be permanently

 

injured by hot water than others. These include the elderly, children, the

 

infirm, or physically/mentally handicapped. If anyone using hot water in

 

your home fits into one of these groups or if there is a local code or state

 

law requiring a certain temperature water at the hot water tap, then you

 

must take special precautions. In addition to using the lowest possible

 

temperature setting that satisfies your hot water needs, a means such

 

as a *mixing valve, shall be used at the hot water taps used by these

 

people or at the water heater. Mixing valves are available local plumbing

 

contractor. Consult a Qualified Installer or Service Agency. Follow

 

mixing valve manufacturer’s instructions for installation of the valves.

 

Before changing the factory setting on the thermostat, read the

 

“Temperature Regulation” section in this manual.

LOCATING THE NEW WATER HEATER

FACTS TO CONSIDER ABOUT THE LOCATION

Carefully choose an indoor location for the new water heater, because

 

the placement is a very important consideration for the safety of the

 

 

occupants in the building and for the most economical use of the

 

appliance.

 

Whether replacing an old water heater or putting the water heater in a

 

new location, the following critical points must be observed:

 

1. Select a location indoors as close as practical or centralized to the

 

water piping system as possible. The water heater should be located

 

in an area not subject to freezing temperatures.

 

2. Selected location must provide adequate clearances (4”) for servicing

 

parts such as the thermostats, drain valve and relief valve.Adequate

 

clearance for servicing this appliance should be considered before

 

installation, such as changing the anodes, etc.

6

Image 6
Contents Residential HUD Side Plumbing Electric Safe INSTALLATION, USE and Service Important DefinitionsGeneral Safety Table of Contents IntroductionTypical Installation Mixing Valve Usage Locating the NEW Water HeaterFacts to Consider about the Location Installing the NEW Water Heater Insulation BlanketsWater Piping TEMPERATURE-PRESSURE Relief Valve Water Piping Pressure TestFilling the Water Heater Valve and Pipe Insulation On Selected Models Wiring Diagrams Wiring Temperature Regulation TemperatureadjustmentFor Your Information Operational ConditionsThermostat Removal / Replacement Periodic MaintenanceTEMPERATURE-PRESSURE Relief Valve Operation Anode ROD InspectionElement Cleaning / Replacement Page Drain Valve Washer Replacement ServiceLeakage Checkpoints Troubleshooting Guidelines Problem Cause SolutionRepair Parts List Manufactured Mobile Home Electric ModelsPage

184748-001 specifications

State Industries 184748-001 is a prominent water heater model that exemplifies advanced engineering and efficiency in residential and commercial applications. With a focus on reliability and energy savings, it is designed to meet the diverse needs of users while ensuring optimal performance.

One of the main features of the 184748-001 is its innovative insulation system. The water heater is equipped with high-density foam insulation that minimizes heat loss, which not only improves energy efficiency but also reduces operating costs. This feature makes it a suitable choice for those looking to lower their utility bills while still enjoying a consistent supply of hot water.

The 184748-001 utilizes a robust heating element that guarantees rapid recovery rates, ensuring that hot water is always available when needed. This model houses a powerful electric heating element that is designed for longevity and efficient operation. As a result, even during peak usage times, users can expect to have a steady flow of hot water, making it ideal for households with high demand or commercial applications.

In terms of capacity, the model can accommodate various needs, featuring a range of tank sizes to suit different households and facilities. Whether you're outfitting a large family home or a small business, the versatility of the 184748-001 allows it to adapt to a multitude of settings, ensuring that it meets the specific demands of each environment.

Another characteristic of this water heater is its user-friendly digital control panel. This feature allows for precise temperature adjustments, making it convenient for users to customize their hot water experience according to personal preferences. The digital interface also includes energy monitoring capabilities, providing insights into consumption patterns that help users make informed decisions regarding their energy usage.

Furthermore, State Industries has prioritized safety in the design of the 184748-001. Equipped with multiple safety features such as temperature and pressure relief valves, this model ensures that the system operates within safe parameters, reducing the risk of accidents and enhancing user confidence.

In summary, the State Industries 184748-001 water heater stands out for its combination of energy efficiency, robust performance, and user-friendly technologies. With its focus on safety and adaptability, it represents a smart investment for those seeking reliable hot water solutions for their homes or businesses.