Multiquip cx400, px400 manual Operation, Hose Connections, Attaching Lifting Rope

Page 17

operation

Hose Connections

1.Connect a 2-inch hose to the discharge port on the pump as shown in Figure 11. Make sure that hose is attached correctly to the discharge port.

Attaching Lifting Rope

1.Attach a suitable lifting cable (rope) to the carrying handle (Figure 11) on the pump and lower the pump into place. For applications where there is an excessive amount of mud, grit or silt, the use of a support platform is desirable.When pumping water from swimming pool type applications where there is little or no debris, the support platform is not required.

 

 

EXTER

 

115 VAC

1Ø 115 VA

 

POWER S

 

POWER

 

 

 

PLUG

CIR

2-INCH

BRE

 

 

 

DISCHARGE

 

BLACK

 

 

HOSE

 

WHITE

 

 

GREEN

 

 

GND. B

 

POWER

 

LIFTING

CORD

 

ROPE

 

 

CARRYING

HANDLE

SUBMERSIBLE

SUBMERSIBLE

PUMP

Figure 12. Submersible Pump

Tilted Position (Incorrect)

Pump Power Connections (No Control Box)

1.

Make sure circuit breaker supplying power to pump

 

motor is in the OFF position.

2.

Insert the power cable plug (Figure 11) into the

 

appropriate power source receptable. The correct

 

source voltage for this pump is 115 VAC, 60 Hz,

 

single-phase.

SUPPORT

PUMP

3. If all of the pump's electrical requirements have been

PLATFORM

Figure 11. Submersible Pump

Upright Position (Correct)

2.Make sure the pump is always placed in an upright position (Figure 11, and not tilted (Figure 12). Never position the pump directly on a soft, loose bottom. Remember to attain maximum pumping capacity and prevent excessive wear. Position the pump so it will not burrow itself into sand or clay.

 

met, place the circuit breaker or power ON/OFF switch

 

in the ON position.

4.

Wait a few seconds and water should begin to flow

 

from the discharge hose.

5.

If water is not flowing from the discharge hose or not

 

flowing freely after a few minutes, place the circuit

 

breaker or ON/OFF switch in the OFF position and

 

check the system for leaks.

NOTICE

When connecting the pump directly to a power source (no control box), it is recommeded that personnel monitor the pump while in operation. Severe pump damge can occur if left unattended.

For unattended operation Multiquip recommends the use of the CB3 control box.

cx400/px400 Sub. pump • operation and parts manual — rev. #1 (12/03/10) — page 17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Model cx400/px400 CX400/PX400 Submersible Pump Table of ContentsChoose from three easy options SaFetY meSSageS Safety InformationSaFetY SYmbolS SymbolGeneral SaFetY „ never disconnect any emergency or Pump SaFetY„ do not attempt to thaw out a frozen pump by using Control box Safety Power Cord/Cable SafetyLiFting SaFetY Grounding SafetyPX400 DimensionsModel CX400/PX400 SpecificationModel Voltage Type UL/CSAPump Performance Curve Performance curveGeneral information Allows the pump to run dry for a limited period of time ComponentsDirect Power Operation Direct power operationMechanical Float Switch Float switchesDesign Features How It WorksMounting The Float Switches Float SwitchesCB3 Control Box Float switches control boxOperation Pump Power Connections No Control BoxHose Connections Attaching Lifting RopeSingle-Phase Power Installation Input Control Box InstallationPower Cord Requirements Control Box MountingConnecting AC Power to the CB3 Control Box Connecting Dual float Switch SW-1WOP To Control BoxConnecting AC Power to the Pump Motor ContractorManual Operation Turning On The PumpAutomatic Operation Shut-DownCleanup MaintenanceLubrication Lay pump flat on its side PX400 only as shown in FigureRemove the bolts securing the casing cover to the casing Impeller/Mechanical Seal Replacement PX400Impeller/Mechanical Seal Replacement CX400 Why perform electrical insulation testing? Electrical Insulation TestingSolution SymptomWiring Diagram Cb3 Control BoX wiring diagramExplanation of Code in Remarks Column Qty Description Suggested Spare PartsTo 3 Units CX400 pump assy Part Name QTY PX400 pump assy Part Name QTY Remarks FreigHt policY Terms and Conditions of Sale PartsPage HERE’S HOW to GET Help

px400, cx400 specifications

The Multiquip CX400 and PX400 are cutting-edge equipment designed to make tasks in construction and landscaping more efficient and effective. These models are well-regarded for their reliability, durability, and advanced features, making them suitable for a wide range of applications.

The CX400 is known for its robust construction and powerful performance. It features a heavy-duty frame, which provides excellent stability during operation. The model is equipped with a reliable engine that ensures high torque and performance, allowing it to tackle various tasks with ease. Additionally, the CX400 boasts advanced hydraulic systems that enhance its lifting capacity and operational efficiency, making it ideal for heavy lifting and material handling in various environments.

On the other hand, the PX400 is designed for versatility and efficiency. This model is particularly well-suited for urban applications and tighter spaces due to its compact design. Despite its smaller size, the PX400 doesn't compromise on power. It offers an impressive lifting capacity and is equipped with a smooth-operating hydraulic system that allows for precise control during operation.

Both models come with user-friendly controls that simplify operation and increase productivity. The ergonomic design of the operator’s platform ensures comfort during extended use. Additionally, these machines feature enhanced safety features, including a robust guarding system and emergency stop functions, ensuring the safety of operators and personnel on job sites.

Another notable characteristic of the CX400 and PX400 is their fuel efficiency. Designed with modern engines that minimize fuel consumption while maximizing output, these models can significantly reduce operational costs over time. They are also engineered for easy maintenance, featuring accessible components that make routine checks and servicing straightforward.

Moreover, the Multiquip CX400 and PX400 are compatible with various attachments, allowing users to customize their machines for specific tasks. This adaptability makes them an invaluable asset to contractors and equipment rental companies alike.

In conclusion, the Multiquip CX400 and PX400 stand out in the construction and landscaping industry due to their powerful performance, advanced technologies, user-friendly features, and versatility. They are engineered to meet the demands of modern job sites while ensuring safety, efficiency, and reliability. Whether for heavy lifting or operating in confined spaces, these machines are equipped to handle a range of tasks effectively.
Top Page Image Contents