Gardena FSP 15000 System Extensions Product Recommendations, Operation, Care Instructions

G

Check line voltage

Do not operate pump when there are people in the water

Swimming pools and garden ponds

Do not use power cable to carry the pump

Disconnect plug

Temperature of the liquid used

Wear and reduced output

Observe local noise prevention regulations

pump checked by our GARDENA Service Centre or by an authorised electrician.

Check line voltage. Data indicated on the type plate must match technical data of the mains supply.

The pump must not be operated when there are people in the water.

Swimming pools and garden ponds should be designed accord- ing to international and national design regulations. Please consult a professional electrician.

Do not use the power cable to carry the pump or to pull the plug out of the socket. Protect the power cable from heat, oil and sharp edges.

Please unplug the pump after operation and before carrying out any maintenance works.

The temperature of the liquid used must not be below 4 °C or above 35 °C.

Sand and other abrasive substances in the liquid cause in- creased wear and reduce the output of the pump.

Please observe the local noise prevention regulations.

G

Fitting the universal	1. Push the sleeve nut over the universal connector.
connector	2. Place the sealing ring in the sleeve nut.
	3. Screw the universal adapter and sleeve nut onto the pressure
	joints of the pump.
Positioning the pump	Position the pump on a firm base so that it is at least 20 cm
	immersed in water.
Pay attention to	Please note the maximum submersion depth (see “Technical Data”).
minimum water depth
Starting the pump	Connect the power cable to a 230 V AC socket.
	A Caution! Pump will start running immediately!
Avoid dry operation	Avoid dry operation of the pump as dry running will produce
	undesirable heat and destroy the pump.

System Extensions – Product Recommendations

Operating an external filter	To clean your pond you can connect an external filter such as the
	GARDENA Pond Filter	Art. No. 7904
	GARDENA Pond Filter with UVC-light	Art. No. 7905
	For this purpose use a hose in order to connect the Pump
	for Filters and Streams with the external filter.

Operation
	The universal fitting provides you with various possibilities
G 3/4	to fit a hose:
1”	➔ Connection via graduated nipple of
	. 25 mm (1”)- or
	. 32 mm (5/4”)- or
G 1	. 38 mm (1 1/2 ”)- hoses
5/4”	➔ Connection via GARDENA Water hose-Plug-in-system
	fittings of
1 1/2 ”	. 13 mm (1/2 ”)- or
	. 16 mm (5/8 ”)- or
	. 19 mm (3/4”)- hoses
	Recommendation:
	Fix 38 mm (1 1/2 ”)-, 32 mm (5/4”)- and 25 mm (1”)-hoses
	additionally with a hose clip.
	Cut off the parts of the universal fitting that you do not need
	with a saw.
10

	A Please observe the information on safety in the relevant
	operating instructions!
Operating a stream	The pump has been designed for streams and waterfalls:

.Large streams and waterfalls

➔Connect a 38 mm (1 1/2 ”) GARDENA Pond Hose, Art. No. 7898, and run it to the source of your stream.

.Smaller streams

➔Connect hoses with a smaller diameter correspondingly e.g.: 32 mm (5/4”)-GARDENA Pond Hose, Art. No. 7897

25 mm (1”)-GARDENA Pond Hose, Art. No. 7896.

Care Instructions

Cleaning the pump	If you use your pump frequently in dirty water you should clean
	your pump as follows:
	1. Remove the mains plug.
	2.	Take the pump out of the water.
	3.	Rinse the housing of the pump thoroughly with water.
		If necessary, also direct the water into the pressure outlet.
	4.	Put the pump back into your pond or stream.

Information: Do not use any hard objects or strong detergents!

11