Multiquip manual ST-1500 Series SUB. PUMP- Control BOX Installation, Control Box Mounting

Page 16

ST-1500 SERIES SUB. PUMP— CONTROL BOX INSTALLATION

DANGER

The ST-1500 series submersible pumps are also designed to work with a control box (Model CB3).This control box contains the necessary

electronics (float switch connections) to operate the pump. Remember this control box contains hazardous voltages. Disconnect all sources of power before installing or servicing. There exists the possibility of electrocution, electric shock or burn, which can cause severe bodily harm or even death!

CAUTION

This control box should only be installed or serviced by a licensed electrician or qualified personnel.

Control Box Mounting

Mount thecontrol box in anupright vertical position.Makesure the control box is securely fastened to a flat surface, that is free of dust, dirt, moisture or any elements that may contaminate or erode the electronic components of the control box.

Single-Phase Power Installation (Input)

All ST-1500 series submersible pumps require 115 V, 60 Hz., single-phase power for normal operation.

If you cannot determine what your pump's power requirements are, look at the vendor supplied identification name tag attached to the pump or please contact Multiquip's Service/Technical Assistance department.

CAUTION

Applying incorrect power (voltage phasing) to the submersible pump can cause severe damage to the pump. Please make sure that the correct voltage and phase are transferred to the pump at all times.

Power Cord Requirements

When routing the 115 VAC, 60 Hz., single phase power via a power cord to the control box, ALWAYS use the correct wire size. Please reference Table 4 below (Cord Length/Wire Size) to determine the correct wire size. Incorrect wire size can adversely affect the performance of the pump.

TABLE 4. CORD LENGTH AND WIRE SIZES

AMPS

50 FT.

100 FT.

150 FT.

 

 

 

 

6

16 AWG

16 AWG

14 AWG

 

 

 

 

8

16 AWG

14 AWG

12 AWG

 

 

 

 

10

16 AWG

14 AWG

12 AWG

 

 

 

 

12

14 AWG

14 AWG

12 AWG

 

 

 

 

14

14 AWG

12 AWG

10 AWG

 

 

 

 

16

12 AWG

12 AWG

10 AWG

 

 

 

 

Connecting Dual float Switch (SW-1WOP) To Control Box

1.Remove the float switch input connector housing, then route the float switch wires through the cable gland on the control box. Attach the wires of the float switch to the terminal block as indicated by Table 5 and Figure 6.

TABLE 5. FLOAT SWITCH CONNECTIONSS

FLOAT SWITCH

TERMINAL BLOCK

NUMBER

 

 

 

START

TERMINAL 1 (BLACK)

TERMINAL 2 (WHITE)

 

 

 

STOP

TERMINAL 7 (WHITE)

TERMINAL 8 (BLACK)

 

 

 

2.Tighten the connector housing to ensure a tight fit between the cord and the connector body.This will prevent the cable from pulling out of the terminal block and also prevent moisture from entering the control box.

3.Determine the length of the float switch wires, then secure float switch wires to pump discharge hose. See Figures 3 and 6 and Table 3 to determine the pumping range.

PAGE 16 — ST-1500 SERIES SUBMERSIBLE PUMPS — OPERATION & PARTS MANUAL — REV. #0 (10/04/04)

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Submersible Pumps Model ST-1500 Series Heres HOW to GET Help ST-1500 Series SUB. Pump Table of Contents ST-1500 Series SUB. Pump Parts Ordering Procedures When ordering parts Please supply the following informationST-1500 Series SUB. Pump Safety Message Alert Symbols For Your Safety and the Safety of OthersGeneral Safety ST-1500 Series SUB. Pump Rules for Safe OperationMaintenance Safety EmergenciesST-1500 Series SUB. Pump Dimensions ST-1500 Series SUB. Pump Specifications SpecificationsControl Box Installation Warnings IntroductionST-1500 Series SUB. Pump Components Submersible Pump ComponentsDesign Features Float Switch TheoryHow It Works Float Switch ST-1500 Series SUB. Pump Float Switch PIGGY-BACKMounting The Float Switch ST-1500 Series SUB. Pump Float Switch Control BOX Control Box CB3Pump Power Connections Piggy-Back Cord Only ST-1500 Series SUB. Pump OperationHose Connections Attaching Lifting RopeST-1500 Series SUB. PUMP- Control BOX Installation Single-Phase Power Installation InputPower Cord Requirements Connecting Dual float Switch SW-1WOP To Control BoxConnecting AC Power to the Control Box Connecting AC Power to the PumpST-1500 Series SUB. Pump CLEAN-UP Pump Shut-Down/Clean-upST-1500 Series SUB. Pump Maintenance Checking Hydraulic OilST-1500 Series SUB. Pump -TROUBLESHOOTING ST-1500 Series SUB. Pump Performance Curves Pump Performance CurvesST-1500 Series SUB. Pump Wiring Diagrams Page ST-1500 Series SUB. Pump Explanation of Code in Remarks Without noticeST-1500 Series SUB. Pump Suggested Spare Parts ST-1503A Electric Submersible Pump Assy Part Name 299 SUC Cover ST-1503CUL Electric Submersible Pump Assy 0201503001 ST-1503CUL Electric Submersible Pump Assy 176 0201503176 ST-1503A/CUL Electric Motor Assy ST-1503A/CUL Electric Motor Assy Effective October 1, 2002 Terms and Conditions of Sale Parts Page Your Local Dealer is

ST-1500 specifications

The Multiquip ST-1500 is a versatile and powerful equipment designed for various applications in construction and landscaping. This machine excels in its category due to its combination of efficiency, durability, and ease of use. Whether you are tackling small landscaping tasks or larger grading projects, the ST-1500 has the features to meet your needs.

One of the standout features of the Multiquip ST-1500 is its robust engine. Equipped with a reliable gasoline-powered engine, it delivers impressive performance while ensuring fuel efficiency. This allows operators to work longer hours without the constant need for refueling, making it ideal for extensive job sites.

The ST-1500 also boasts an advanced hydrostatic transmission system. This technology provides smooth and precise control over speed and direction. Operators can effortlessly maneuver the machine in tight spaces and on uneven terrain. The variable speed control allows for a tailored approach to different tasks, further enhancing productivity.

Safety is paramount in any construction equipment, and the Multiquip ST-1500 addresses this concern with well-thought-out design features. It includes a sturdy roll-over protection structure (ROPS) and operator presence controls to prevent accidental operation. These safety features ensure that users can operate the machine with confidence.

In terms of versatility, the ST-1500 can be outfitted with various attachments, making it suitable for a range of applications. From digging and grading to lifting and transporting materials, this machine can adapt to the specific demands of each job. Additionally, its compact size allows it to navigate through narrow passages and deliver performance in restricted spaces.

The ST-1500 is also designed for low maintenance, which is a significant advantage for contractors and landscapers. Its accessible components make routine checks and maintenance straightforward, minimizing downtime and keeping projects on schedule.

In conclusion, the Multiquip ST-1500 is a well-engineered machine that combines power, safety, and versatility in one compact package. With its innovative technologies and user-friendly design, it stands out as an essential tool for professionals in the construction and landscaping industries, capable of tackling a variety of tasks with ease and efficiency. Whether you are working on grading, landscaping, or material handling, the ST-1500 is engineered to deliver reliable performance that professionals can depend on.
Top Page Image Contents